AP630 Hardware User Guide

Safety Guidelines

Safety Guidelines

The information in this section applies to AP630 devices.

The following safety icons are used in these guidelines to identify the type of precaution:

	This icon indicates a general caution. Failure to comply with a caution notification can result in damage to equipment.
	This icon indicates an electrical caution. Failure to comply with an electrical notification can result in serious injury or death, and extensive damage to equipment.
	This icon indicates a laser caution. Failure to comply with a laser caution can result in serious injury.
The following table lists the safety precautions you should follow when installing your AP630 devices.
	Extreme Networks devices must be installed by a professional installer who is certified to install these types of devices and to ensure that they are properly grounded and meet applicable local and national electrical codes.
	These devices are intended for indoor use only.
	Do not install the device in an environment where the operating ambient temperature might exceed the recommended ranges.
	For products available in the USA/Canada market, for the 2.4 GHz band, only channels 1-11 can be operated. Selection of other channels is not possible.
	Changes or modifications made to this device that are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
	Use only attachments and accessories specified by Extreme Networks.
	These devices are not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or with lack of experience of knowledge unless they are given supervision or instruction concerning use of the devices by a person who is responsible for their safety. Children should be supervised to ensure that they do not play with the devices.
	Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs when electronic components are improperly handled and can result in complete or intermittent failures. Be sure to follow ESD-prevention procedures when handling electronic components and equipment.
	During operation, the surfaces of the AP630 can become hot. Use caution when handling.
	To meet federal radiation exposure requirements, these devices should be installed at a minimum distance of 11" (28 cm) from people or animals.

Install the AP

The following sections describe how to mount your AP on a dropped ceiling track or to a wall.

Shipping Carton Contents

The AP630 access point shipping carton contains the following items:

• AP630 chassis
• AP630 mounting bracket
• Read Me card

You can mount the AP630 on a flat surface or wall, or on the rails of a standard dropped ceiling grid. There is also an accessory mounting bracket that allows you to install the device in Armstrong-style dropped ceilings (ordered separately).

The following sections describe how to install your AP630 devices and connect them to the network.

Use the following illustration to install the mounting bracket to a dropped ceiling rail.

Install the AP on a Ceiling Track

The AP630 ships with a mounting bracket that lets you easily install it on the rail of a standard dropped ceiling grid.

Once the bracket is secure, you can install the AP by aligning the red dot on the bracket with the red dot on the AP. Keeping the dots aligned, raise the AP up until the bracket fits into the circular depression in the bottom of the AP. When the AP is firmly seated, rotate it clockwise until it clicks in to place as shown here.

Mount the AP on a Wall

Use the holes in the bracket as a template to mark the wall. Drill holes in the wall and attach the bracket to the wall using wall screws and wall anchors if necessary. Attach the AP to the bracket in the same manner as shown in the previous section.

Connect the AP to the Network

Follow these steps to connect your AP630 to PoE (Power over Ethernet) power and to the network.

1. Connect a standard RJ45 Ethernet cable from ETH0 on the AP to a switch that provides PoE power, or use a PoE injector (see "Ethernet Ports").
2. After the AP receives power, it automatically tries to get network settings and contact ExtremeCloud IQ. This process takes about five minutes. When you see the AP listed on the Devices page in the Manage section of the ExtremeCloud IQ GUI, the initial setup is complete and you can begin managing the AP with ExtremeCloud IQ.

Hardware Components

You can see the hardware components of the AP630 in the illustration below and read about them in the sections that follow.

Component Descriptions

Status Light

The round status light on the top corner of the device conveys operational states for system power, firmware updates, Ethernet and wireless interface activity, and major alarms. The AP630 has a round status light on the top right corner of the chassis. At setup, this light cycles through the following sequence:

• Steady Amber: The device is initializing.
• Slow-blinking White: The device is receiving 802.3af power, instead of 802.3at power.
• Fast-blinking White: The device is looking for a mesh neighbor from which to obtain a password.
• Slow-blinking Amber (AF power mode only): The device is attempting to establish a connection or has established a CAPWAP connection with ExtremeCloud IQ.
• Fast-blinking Amber: The device is performing a IQ Engine or ExtremeCloud IQ upgrade.
• Steady White: The device has successfully established a CAPWAP connection and is operating normally.

Ethernet Ports

The AP630 has two RJ45 Ethernet ports (Eth0 and Eth1) that automatically negotiate half- and full-duplex connections with the connecting device. The ports are autosensing and adjust to straight-through and crossover standard Cat2, Cat5, Cat5e, or Cat6 Ethernet cables automatically. The AP receives power through an Ethernet connection to the ETH0 port from PSE (power sourcing equipment) that is compatible with the 802.3at and 802.3at standards.

Console Port

The AP630 has one RJ45 Console port. Use this port to make a serial connection between your management system and the AP. The management station from which you connect to the device must have a VT100 emulation program, such as Tera Term Pro © (a free terminal emulator) or Hilgraeve HyperTerminal ® (provided with Windows ® operating systems from XP forward). The serial connection settings are: 9600 bits per second, 8 data bits, no parity, 1 stop bit, no flow control.

USB Port

The AP630 has a USB port that you can use to connect USB-based beacons (iBeacon, for example) and IoT (Internet of Things) devices. To access the port, remove the screw that secures the protective cover.

Reset Button

Use the Reset button to reset the device or restore the factory default settings. Insert a paper clip or similar tool into the Reset pinhole and press the button. To reboot the device, press the button for 5 seconds. To return the configuration to the factory default settings, press it for at least 10 seconds. After releasing the button, the indicator light goes dark, and then glows steady amber while the firmware loads and the system performs a self-test. After the software finishes loading and the AP has connected to ExtremeCloud IQ, the status indicator glows steady white.

To prevent the reset button from resetting the configuration, enter this command:

no reset-button reset-config-enable

When this command is enabled, pressing the button for 5 seconds will still reboot the AP, but pressing it for more than 10 seconds will not reset its configuration.

Security Lock Slot

You can secure the AP using a Kensington® lock in the lock slot on the the device, or you can use a security bracket and a crosshead screw or a security screw. Security brackets and screws can be ordered separately from Extreme Networks (not available in Brazil).

Extreme Networks recommends a variety of Kensington locks. For more information, contact your sales representative.

Hardware Specifications

The following sections list radio, device, power, and environmental specifications for the AP630.

Radio Specifications

Bluetooth BLE Beacon

• 2402 - 2480 MHz
• Frequency Hopping Spread-spectrum (FHSS)

802.11a

• 5.150-5.350, 5.470 - 5.850 GHz operating frequency
• Orthogonal Frequency Division Multiplexing (OFDM) modulation
• Rates (Mbps): 54, 48, 36, 24, 12, 9, 6 with auto fallback

802.11b

• 2.4-2.48 GHz operating frequency
• Direct-Sequence Spread-Spectrum (DSSS) modulation
• Rates (Mbps): 11, 5.5, 2.1 with auto fallback

802.11g

• 2.4-2.48 GHz operating frequency
• Orthogonal Frequency Division Multiplexing (OFDM) modulation
• Rates (Mbps): 54, 48, 36, 24, 12, 9, 6 with auto fallback

802.11n

• 2.4-2.48 and 5.150-5.350, 5.470 - 5.850 GHz operating frequency
• 802.11n modulation
• Rates: MCS0 - MCS7
• 4x4 MIMO radio
• HT20/HT40 support
• A-MPDU and A-MSDU frame aggregation

802.11ac

• 802.11ac modulation (256-QAM)
• 2.4 - 2.48 GHz MCS0-9, NSS=1-4
• 5.150-5.350, 5.470 - 5.850 GHz operating frequency
• Rates: MCS0 - MCS9, NSS = 1-4
• 4x4 MIMO radio
• VHT20/VHT40/VHT80 support

802.11ax

• 5.150-5.350, 5.470 - 5.850 GHz operating frequency

• 2.4 – 2.48 GHz operating frequency

• 802.11ax modulation (1024-QAM)
• Rates: MCS0 - MCS11, NSS = 1-4
• OFDMA support
• 4x4 MU-MIMO
• HE20/HE40/HE80/HE160 support

Transmit Power and Sensitivity Specifications

Note

Output power may be limited by regulatory requirements.

2.4 G:

Device Specifications

• Chassis dimensions: 8.1” W 8.1” H 1.46” D (205 mm x 205 mm x 37 mm)
• Weight: 1.98 pounds (0.9 kilograms)
• Four dual-band internal WiFi antennas and one BLE internal antenna

• Console serial port: RJ45 (9600 bits per second, 8 data bits, parity: none, 1 stop bit, no flow control

• Eth0 Ethernet port: autosensing 10/100/1000Base-T/TX Mbps, with 802.3at-compliant PoE

• Eth1 Ethernet port: autosensing 10/100/1000Base-T/TX Mbps

Antenna Gain

• 2.4 GHz: 4.2 dBi gain
• 5 GHz: 5.4 dBi gain

Power Specifications

• PoE input voltage range: 37-57 V
• Typical PoE power consumption is 22 W
• RJ45 power input pins: Wires 4, 5, 7, 8 or 1, 2, 3, and 6

Environmental Specifications

• Operating temperature: 32° to 104° F (0° to 40° C)

• Storage temperature: -40° to 185° F (-40° to 85° C)

• Relative Humidity: 5 to 95% RH (noncondensing)

Regulatory Compliance Statements

The regulatory compliance statements in this section apply to Extreme NetworksAP630 devices.

Japan Indoor Use

Note

For Japan, the AP630 is restricted for indoor use in the 5150-5350 MHz band only.

Compliance Statement - Europe

EU Declaration of Conformity

View full CE Declaration of Compliance and this information online at www.aerohive.com/support/regulatory-compliance

Extreme Networks, Inc. declares that this device complies with the essential requirements of the Radio Eqiupment Directive 2014/53/EU.

• Bulgarian [български]: [Extreme Networks] С настоящото [Extreme Networks] декларира, че този тип радиосъоръжение [AP630] е в съответствие с Директива 2014/53/ЕU.
• Croatian [hrvatski]: [Extreme Networks] ovime izjavljuje da je radijska oprema tipa [AP630] u skladu s Direktivom 2014/53/EU. 
• Czech [Česky]: [Extreme Networks] Tímto [jméno výrobce] prohlašuje, že typ rádiového zařízení [AP630] je v souladu se směrnicí 2014/53/EU.
• Danish [Dansk]: Hermed erklærer [Extreme Networks], at radioudstyrstypen [AP630] er i overensstemmelse med direktiv 2014/53/EU.
• Dutch [Nederland]Hierbij verklaar ik, [Extreme Networks], dat het type radioapparatuur [AP630] conform is met Richtlijn 2014/53/EU.
• English: Hereby, [Extreme Networks], declares that this [ Atom AP30] is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
• Estonian [Eesti]: Käesolevaga deklareerib [Extreme Networks], et käesolev raadioseadme tüüp [AP630] vastab direktiivi 2014/53/EL nõuetele.
• Finnish [Suomi]: [Extreme Networks] vakuuttaa, että radiolaitetyyppi [AP630] on direktiivin 2014/53/EU mukainen..
• French [Français]: Le soussigné, [Extreme Networks], déclare que l'équipement radioélectrique du type [AP630] est conforme à la directive 2014/53/UE.
• German [Deutsch]: Hiermit erklärt [Extreme Networks], dass der Funkanlagentyp [AP630] der Richtlinie 2014/53/EU entspricht.
• Greek [Ελληνική]: ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [Extreme Networks] ΔΗΛΩΝΕΙ ΟΤΙ [ AP630] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 2014/53/EU.
• Hungarian [Magyar]: [Extreme Networks] igazolja, hogy a [AP630] típusú rádióberendezés megfelel a 2014/53/EU irányelvnek.

• Italian [Italiano]: Il fabbricante, [Extreme Networks], dichiara che il tipo di apparecchiatura radio [AP630] è conforme alla direttiva 2014/53/UE.
• Latvian [Latviski]: Ar šo [Extreme Networkss] deklarē, ka radioiekārta [AP630] atbilst Direktīvai 2014/53/ES.
• Lithuanian [Lietuvių]: Aš, [Extreme Networks], patvirtinu, kad radijo įrenginių tipas [AP630s] atitinka Direktyvą 2014/53/ES.
• Maltese [Malti]: B'dan, [Extreme Networks], niddikjara li dan it-tip ta' tagħmir tar-radju [AP630] huwa konformi mad-Direttiva 2014/53/UE.
• Polish [Polski]: [Extreme Networks] niniejszym oświadcza, że typ urządzenia radiowego [AP630] jest zgodny z dyrektywą 2014/53/UE.
• Portuguese [Português]: O(a) abaixo assinado(a) [Extreme Networks] declara que o presente tipo de equipamento de rádio [AP630] está em conformidade com a Diretiva 2014/53/UE.
• Romanian [Romania]: Prin prezenta, [Extreme Networks] declară că tipul de echipamente radio [AP630] este în conformitate cu Directiva 2014/53/UE.
• Slovak [Slovensky]: [Extreme Networks] týmto vyhlasuje, že rádiové zariadenie typu [AP630] je v súlade so smernicou 2014/53/EÚ.
• Slovenian [Slovenija]: [Extreme Networks] potrjuje, da je tip radijske opreme [AP630] skladen z Direktivo 2014/53/EU.
• Spanish [Español]: Por la presente, [Extreme Networks] declara que el tipo de equipo radioeléctrico [AP630] es conforme con la Directiva 2014/53/UE.
• Swedish [Sverige]: Härmed försäkrar [Extreme Networks] att denna typ av radioutrustning [AP630] överensstämmer med direktiv 2014/53/EU.

Radio Specifications

Bluetooth BLE Beacon

• 2402 - 2480 MHz
• Frequency Hopping Spread-Spectrum (FHSS)

USA and Canada Radio Frequency Bands

a. USA

b. Canada

EU Radiation Warning Statement

To meet radiation exposure requirements, these devices should be installed at a minimum distance of 12" (30 cm) from people or animals.

Restrictions: 5150-5350 MHz for indoor use only.

Bulgarian [български]: За да отговарят на изискванията за излагане на радиация, тези устройства трябва да бъдат инсталирани на минимално разстояние от 30 см от хората или животните.

Ограничения: 5150-5350 MHz само за вътрешна употреба.

Croatian [hrvatski]: Da bi zadovoljili zahtjeve izloženosti zračenju, ti uređaji trebaju biti instalirani na minimalnoj udaljenosti od 30 cm od ljudi ili životinja.

Ograničenja: 5150-5350 MHz samo za unutarnju uporabu.

Czech [Česky]: Aby byly splněny požadavky na ozáření, měly by být tato zařízení instalována v minimální vzdálenosti 30 cm od lidí nebo zvířat.

Omezení: 5150-5350 MHz pouze pro vnitřní použití.

Danish [Dansk]: For at opfylde kravene til strålingseksponering skal disse enheder installeres i mindst 12" (30 cm) afstand fra mennesker eller dyr.

Restriktioner: 5150-5350 MHz kun til indendørs brug.

Dutch [Nederland]: Om aan stralingsblootstelling te voldoen, dienen deze apparaten op een minimumafstand van 12" (30 cm) van mensen of dieren te worden geïnstalleerd.

Beperkingen: 5150-5350 MHz alleen voor gebruik binnenshuis.

English: To meet radiation exposure requirements, these devices should be installed at a minimum distance of 12" (30 cm) from people or animals.

Restrictions: 5150-5350 MHz for indoor use only.

Estonian [Eesti]: Et rahuldada kiirituse nõuetele, need seadmed tuleb paigaldada minimaalselt 12" (30 cm) inimestelt või loomadelt.

Piirangud: 5150-5350 MHz sisetingimustele.

Finnish [Suomi]: Säteilytysvaatimusten täyttämiseksi nämä laitteet on asennettava vähintään 12" (30 cm) etäisyydelle ihmisistä tai eläimistä.

Rajoitukset: 5150-5350 MHz vain sisäkäyttöön.

French [Français]: Pour répondre aux exigences d'exposition aux rayonnements, ces appareils devraient être installés à une distance minimale de 12" (30 cm) des personnes ou des animaux.

Restrictions: 5150-5350 MHz pour usage intérieur seulement.

German [Deutsch]: Um die Anforderungen an die Strahlenbelastung zu erfüllen, sollten diese Geräte in einem Abstand von 12" (30 cm) von Personen oder Tieren installiert werden.

Einschränkungen: 5150-5350 MHz nur für den Innenbereich.

Greek [Ελληνική]: Για την κάλυψη των απαιτήσεων έκθεσης σε ακτινοβολία, οι συσκευές αυτές πρέπει να τοποθετούνται σε απόσταση τουλάχιστον 30 cm από ανθρώπους ή ζώα.

Περιορισμοί: 5150-5350 MHz μόνο για εσωτερική χρήση.

Hungarian [Magyar]: A sugárterhelési követelmények teljesítése érdekében ezeket az eszközöket legalább 12" (30 cm) távolságra kell felszerelni az emberek vagy az állatoktól.

Korlátozások: 5150-5350 MHz csak beltéri használatra.

Italian [Italiano]: Per soddisfare i requisiti di esposizione alle radiazioni, questi dispositivi devono essere installati ad una distanza minima di 30 cm da persone o animali.

Restrizioni: 5150-5350 MHz solo per uso interno.

Latvian [Latviski]: Lai apmierinātu starojuma iedarbības prasībām, šīs ierīces ir uzstādītas pie minimālo attālumu 12" (30 cm) no cilvēkiem vai dzīvniekiem.

Ierobežojumi: 5150-53250 MHz izmantot tikai telpās.

Lithuanian [Lietuvių]: Siekiant patenkinti SPINDULIAVIMĄ reikalavimus, šie įtaisai turi būti įrengiami ne arčiau kaip 12" (30 cm) nuo žmonių ar gyvūnų.

Apribojimai: 5150-5350 MHz naudoti tik patalpose.

Maltese [Malti]: Biex jilħqu l-ħtiġiet ta 'espożizzjoni tar-radjazzjoni, dawn il-mezzi għandhom jiġu installati f'distanza minima ta' 12" (30 ċm) minn nies jew annimali.

Restrizzjonijiet: MHz 5150-5350 għall-użu fuq ġewwa biss.

Polish [Polski]: Aby spełnić wymagania dotyczące narażenia na promieniowanie, urządzenia te powinny być instalowane w odległości minimum 12" (30 cm) od ludzi lub zwierząt.

Ograniczenia: 5150-5350 MHz tylko do użytku wewnętrznego.

Portuguese [Português]: Para atender aos requisitos de exposição à radiação, esses dispositivos devem ser instalados a uma distância mínima de 30 cm (12") de pessoas ou animais.

Restrições: 5150-5350 MHz para uso interno apenas.

Romanian [Romania]: Pentru a îndeplini cerințele de expunere la radiații, aceste dispozitive ar trebui instalate la o distanță minimă de 28 cm de la oameni sau animale.

Restricții: 5150-5350 MHz numai pentru uz intern.

Slovak [Slovensky]: Ak chcete splniť požiadavky na vystavenie žiareniu, mali by byť tieto zariadenia inštalované v minimálnej vzdialenosti od ľudí alebo zvierat od minimálnej vzdialenosti 30 cm.

Obmedzenia: 5150-5350 MHz iba pre vnútorné použitie.

Slovenian [Slovenija]: Da bi zadovoljili zahteve izpostavljenosti sevanja, morajo biti te naprave nameščene na razdalji najmanj 12" (30 cm) iz ljudi ali živali.

Omejitve: 5150-5350 MHz samo za uporabo v zaprtih prostorih.

Spanish [Español]: Para cumplir con los requisitos de exposición a la radiación, estos dispositivos deben instalarse a una distancia mínima de 12" (30 cm) de personas o animales.

Restricciones: 5150-5350 MHz sólo para uso en interiores.

Swedish [Sverige]: För att uppfylla kraven på strålningsexponering bör dessa enheter installeras på minst 12" (30 cm) från människor eller djur.

Restriktioner: 5150-5350 MHz endast för inomhusbruk.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the antenna of the receiving devices.
• Increase the separation between this equipment and receiving equipment.
• Connect this equipment into an outlet on a circuit different from that to which the receiving equipment is connected.
• Consult the dealer or an experienced radio or TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 11" (28 cm) between the radiator and people or animals.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Country Code selection feature to be disabled for products marketed to the US/CANADA.

Este equipamento não tem direito à proteção contra inteferência prejudicial e não pode causar interferência em sistemas devidamente autorizados.

La operación de este equipo está sujeta a las siguientes dos condiciones

(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y

(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.

The operation of this equipment is subject to the following two conditions:

(1) it is possible that this equipment or device does not cause disruptive interference and

(2) this equipment or device must accept any interference, including interference that may cause undesired operation).

Industry Canada Statement:

This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions:

• This device may not cause interference, and
• This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :

• l'appareil ne doit pas produire de brouillage, et
• l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Caution:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

Avertissement:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;

Dynamic Frequency Selection (DFS):

Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz.

Sélection dynamique de fréquences (DFS):

Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and people or animals.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et des personnes ou des animaux.

Taiwan Compliance Information

Extreme Networks AP630

第十二條→經型式認證合格之低功率射頻電機，非經許可，公司，商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條→低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用。

無線資訊傳設備的製造廠商應確保頻率穩定性，如依製造廠商使用手冊上所述正常操作，發射的信號應維持於操作頻帶中。

Taiwan MPE Warning

電磁波曝露量MPE標準值(MPE) 1mW/cm²，送測產品實值為0.734 mW/cm²