show ipv6 pim interface

Displays information about the IPv6 PIM-SM interface configuration on the switch.

Syntax

Command Parameters

gigabitEthernet {slot/port[/sub-port][-slot/port[/sub-port]][,...][slot/all][all]}

Identifies the slot and port in one of the following formats:

  • a single slot and port (slot/port)

  • a range of slots and ports (slot/port-slot/port)

  • a series of slots and ports (slot/port,slot/port,slot/port)

  • all ports on the same slot (slot/all)

  • all ports on the switch (all)

If the platform supports channelization and the port is channelized, you must also specify the sub-port in the format slot/port/sub-port.

vlan <1-4059>

Specifies the VLAN ID in the range of 1 to 4059. By default, VLAN IDs 1 to 4059 are configurable and the system reserves VLAN IDs 4060 to 4094 for internal use. On switches that support the vrf-scaling and spbm-config-mode boot configuration flags, if you enable these flags, the system also reserves VLAN IDs 3500 to 3998. VLAN ID 1 is the default VLAN and you cannot create or delete VLAN ID 1.

Default

None

Command Mode

User EXEC

Command Output

The show ipv6 pim interface command displays the following information:

Output field

Description

IF

Indicates the slot and port number or VLAN ID of the interface where PIM is enabled.

MODE

Indicates the configured mode of this interface. The valid modes are SSM and Sparse.

HLINT

Specifies how long to wait (in seconds) before the PIM router sends out the next hello message to neighboring switches. The default hello interval is 30 seconds.

JPINT

Specifies how long to wait (in seconds) before the PIM router sends out the next join or prune message to its upstream neighbors. The default join and prune interval is 60 seconds.

OPSTAT

Indicates the status of PIM on this interface: up or down.

INTF TYPE

Indicates the PIM interface type. The PIM interface type is active.

VLAN-ID or PORT-NUM

Indicates the slot and port number or VLAN ID of the interface where PIM is enabled.

PIM ENABLE

Indicates the administrative status of PIM.

MODE

Indicates the configured mode of this interface. The valid modes are SSM and Sparse.

HELLOINT

Specifies how long to wait (in seconds) before the PIM router sends out the next hello message to neighboring switches. The default hello interval is 30 seconds.

JPINT

Specifies how long to wait (in seconds) before the PIM router sends out the next join or prune message to its upstream neighbors. The default join and prune interval is 60 seconds.

INTF TYPE

Indicates the PIM interface type. The PIM interface type is active.

Example

The command displays information about the IPv6 PIM-SM interface configuration on the switch.

Switch:1>show ipv6 pim interface
======================================================================
                          Pim Interface - GlobalRouter

======================================================================
IF               MODE        HLINT     JPINT     OPSTAT    INTF TYPE
----------------------------------------------------------------------
Vlan2            sparse      30         60        up       active   
    ADDR/MASK :  fe80:0:0:0:12cd:aeff:fe6a:1902/64
    DR        :  fe80:0:0:0:12cd:aeff:fe6a:1902                

Vlan7            sparse      30         60        up       active   
    ADDR/MASK :  fe80:0:0:0:12cd:aeff:fe6a:1903/64
    DR        :  fe80:0:0:0:b647:5eff:fe3a:8582                

Vlan10           sparse      30         60        up       active   
    ADDR/MASK :  fe80:0:0:0:12cd:aeff:fe6a:1900/64
    DR        :  fe80:0:0:0:12cd:aeff:fe6a:1900                

Vlan20           sparse      30         60        up       active   
    ADDR/MASK :  fe80:0:0:0:12cd:aeff:fe6a:1901/64
    DR        :  fe80:0:0:0:12cd:aeff:fe6a:1901                


Total PIM  Interface Entries:  4/0
----------------------------------------------------------------------