The following defects are closed in EFA 2.4.0.
| Parent Defect ID: | EFA-2857 | Issue ID: | EFA-2857 |
| Reason Code: | Will Not Fix | Severity: | S3 - Medium |
| Product: | Extreme Fabric Automation | Reported in Release: | EFA 2.2.0 |
| Symptom: | Addition of fabric ports and MCT ports to the tenant succeeds even though these ports cannot be used to connect to any endpoints. | ||
| Condition: | Addition of fabric ports (ports connecting leaf to spine, spine to super-spine etc) and MCT ports (ports connecting the multi-homed leaf) to the tenant. | ||
| Workaround: | Fabric ports and MCT ports to be not added to the tenant. | ||
| Parent Defect ID: | EFA-4045 | Issue ID: | EFA-4045 |
| Reason Code: | Not Reproducible | Severity: | S2 - High |
| Product: | Extreme Fabric Automation | Reported in Release: | EFA 2.1.0 |
| Symptom: | MCT configuration of two leafs on already Configured fabric was modified manually by replacing the existing MCT ports with a different ports and later updating inventory causing the Leaf devices to go into refresh error, expectation was to push the config of old MCT ports to new | ||
| Workaround: |
Configure the fabric with force efa fabric configure --name <> --force |
||
| Recovery: | Reconfigure fabric with force | ||
| Parent Defect ID: | EFA-5590 | Issue ID: | EFA-5590 |
| Reason Code: | Already Reported | Severity: | S2 - High |
| Product: | Extreme Fabric Automation | Reported in Release: | EFA 2.2.0 |
| Symptom: | EFA CLI behavior on pressing <tab> following a complete command will execute the command handler or will get stuck in cli if waiting on user input on background | ||
| Condition: |
(efa:root)root@ubuntu:~/efa/efa_40# efa inventory rma execute --ip 10.24.95.157 --co<tab> - cli gets stuck and needs ^C^C to exit, as it is waiting on user input on backend (efa:extreme)extreme@tpvm2:~$ efa fabric create --name fab4 – <tab> - this creates a fabric |
||
| Workaround: | These can be avoided by using ‘?‘ before the tab and using the complete command options. In most cases this behavior will not cause an issue, but issue may be seen in cases where there are multiple optional keywords eg in fabric-create, rma execute, fabric add bulk , etc. | ||
| Recovery: | Press ^C^C to exit a command thats stuck on cli. Reverse any command executed as above, if it is not intended. | ||
| Parent Defect ID: | EFA-5689 | Issue ID: | EFA-5689 |
| Reason Code: | Feature/Function Not Supported | Severity: | S2 - High |
| Product: | Extreme Fabric Automation | Reported in Release: | EFA 2.2.0 |
| Symptom: | VRF Backup routing configuration on the SLXOS-9140 will be inadequate and hence the backup routing functionality will not work on SLXOS-9140. | ||
| Condition: | L3 EPG create or update operation with the member ports residing on SLXOS-9140. | ||
| Workaround: | Backup routing needs to be disabled at the fabric setting level if the fabric has SLXOS-9140 devices. | ||
| Recovery: | Backup routing needs to be disabled at the fabric setting level if the fabric has SLXOS-9140 devices. | ||
| Parent Defect ID: | EFA-5952 | Issue ID: | EFA-5952 |
| Reason Code: | Design Limitation | Severity: | S3 - Medium |
| Product: | Extreme Fabric Automation | Reported in Release: | EFA 2.2.0 |
| Symptom: | While executing drift-reconcile port-channels created between MCT pairs and are part of EPG's will be shown as drifted even though the SLX running config is in sync. | ||
| Condition: | This happens when drift is executed while SLX is in maintenance mode. | ||
| Recovery: | Turn off maintenance mode and execute inventory device update which will sync the right status. | ||
| Parent Defect ID: | EFA-6835 | Issue ID: | EFA-6835 |
| Reason Code: | Already Implemented | Severity: | S2 - High |
| Product: | Extreme Fabric Automation | Reported in Release: | EFA 2.3.0 |
| Symptom: | EFA CLIs did not respond following bulk add of devices | ||
| Condition: | Register more 7 devices into EFA at same time using add-bulk fabric CLI in HA multi-node setup. | ||
| Workaround: | Register less then 5 devices in EFA at same time. | ||
| Recovery: | Restart the EFA sever by reloading the Switch. | ||
| Parent Defect ID: | EFA-7237 | Issue ID: | EFA-7237 |
| Reason Code: | Already Reported | Severity: | S3 - Medium |
| Product: | Extreme Fabric Automation | Reported in Release: | EFA 2.3.0 |
| Symptom: |
EFA system backup is generated using efa system backup command. Undeply EFA and install fresh EFA Restore EFA backup generated earlier using "efa system restore" command The restore process preserves the config backup interval and count. However the auto config backup process is not taking backups as configured. |
||
| Condition: | Auto Config backup process does not take expected number of backups as configured. | ||
| Workaround: | User can take config backup manually using "efa inventory config-backup execute". | ||
| Recovery: | Fresh install or restart of EFA application would start the auto config backup process | ||
| Parent Defect ID: | EFA-7264 | Issue ID: | EFA-7264 |
| Reason Code: | Not Reproducible | Severity: | S2 - High |
| Product: | Extreme Fabric Automation | Reported in Release: | EFA 2.3.0 |
| Symptom: | After SLX Switch reload, Configuration drift in port channel members do not get reconciled by EFA | ||
| Condition: |
Below are the steps when the configuration drift created does not get reconciled by EFA: - Configuration of fabric/tenant/po/vrf/epg - 'maintenance mode enable-on-reboot ' enabled on the switch - Drift in configuration created by deleting port channel - Reloading of the switch - As part of reconcilation, port channel was created but Eth <port> was not aggregated to channel-group. |
||
| Workaround: | None | ||
| Recovery: |
Execute manual Drift and Reconcile using this command: " efa inventory drift-reconcile execute --ip <IP of device> --reconcile " |
||
| Parent Defect ID: | EFA-7326 | Issue ID: | EFA-7326 |
| Reason Code: | Cannot Fix | Severity: | S3 - Medium |
| Product: | Extreme Fabric Automation | Reported in Release: | EFA 2.3.0 |
| Symptom: | VRF used in EndpointGroup having invalid Target Network cause Drift & Reconcile operation to fail with error- "Target network is invalid" | ||
| Condition: |
1) VRF is created with Invalid Target Network in earlier version of EFA (before EFA 2.3.0) 2) EndpointGroup is created with same VRF in earlier version of EFA (before EFA 2.3.0) 3) Drift and Reconcile operation is performed |
||
| Workaround: | NA | ||
| Recovery: |
1) Delete EndpointGroup using VRF having invalid Target Network 2) Delete VRF 3) Recreate VRF with valid Target Network 4) Recreate EndpointGroup with new VRF |
||
| Parent Defect ID: | EFA-7389 | Issue ID: | EFA-7389 |
| Reason Code: | Will Not Fix | Severity: | S3 - Medium |
| Product: | Extreme Fabric Automation | Reported in Release: | EFA 2.3.0 |
| Symptom: | In a very rare scenario, http daemon may not start | ||
| Workaround: | Reload SLX device | ||
| Parent Defect ID: | EFA-7406 | Issue ID: | EFA-7406 |
| Reason Code: | Working as Designed | Severity: | S3 - Medium |
| Product: | Extreme Fabric Automation | Reported in Release: | EFA 2.3.1 |
| Symptom: | When EPG deleted during admin-down for any device, after admin-up for that device app-state changed to cfg-refreshed | ||
| Condition: |
1) Configure non-clos fabric 2) Create tennat, vrf, po and epg's 3) Make any of the device to admin down 4) During admin-down, delete one of the epg's created 5) Make same device admin-up 6) EPG app-state moved to cfg-refreshed instead of cfg-in-sync |
||
| Workaround: | NA | ||
| Recovery: | Delete epg once device admin state is up. | ||