There is no new hardware supported for Release 10.7.5.
This release of ExtremeCloud IQ Engine includes various compliance updates.
| Feature ID | New feature | Description |
|---|---|---|
| HOS-20193 | Real-Time Troubleshooting (RTTS) and Packet Capture over Inlets | IQ Engine supports near Real-Time Troubleshooting and datastream on the 6E access points, including AP3000/X, AP5010, and AP5050U/D. |
| HOS-20268 | Support 802.3az Green Ethernet for AP5020 | IQ Engine supports Energy-Efficient Ethernet (EEE) or IEEE 802.3az on the AP5020. Enable EEE to permit the network port to switch between an active mode (during data transmission) and idle mode (when there is no Ethernet traffic). With this feature, physical layer transmitters consume less power when they are in a state of idleness or low data activity. |
| HOS-20481 | Hotspot 2.0 Configuration Support for IQ Engine | IQ Engine supports Hotspot 2.0 configuration. |
| HOS-21081 | AFC: Change of channel or power notifications | IQ Engine provides notifications for AFC change of channel or power requests, where the change disables radio, and also for the initial enabling of an AFC controlled radio. |
| HOS-21083 | Generic Scan: Chorus and HTTP Post support for Universal HW 6E APs | IQ Engine supports Chorus and HTTP Post for all Wi-Fi 6E-capable APs. |
| HOS-21182 | WiFi 6 and 6E AP IOT Scans: Remove duplicate entries in HTTP post as default | By default, BLE scans have unique BLE entries. IQ Engine supports a CLI option to remove duplicates that must be turned OFF if you prefer to receive multiple entries for same tag. On WiFi 6E APs this feature supports iBeacon and Generic BLE scans. On WiFi 6 APs, this feature supports iBeacon scans only. |
| HOS-21196 | AP5020/AP4020 IOT Scans: Option to remove duplicate entries in HTTP post | By default, BLE scans have unique BLE entries. IQ Engine supports a CLI option to remove duplicates that must be turned OFF if you prefer to receive multiple entries for same tag. On AP5020 and AP4020, this feature supports iBeacon, Eddystone and Generic BLE scans. |
| HOS-21205 | AP5020: Increase tag entries for HTTP-Post batch reporting | Up to 300 BLE entries are reported per batch interval in HTTP Post. On AP5020, this feature supports iBeacon, Eddystone and Generic BLE scans. |
| HOS-21208 | AP5020 - Upgrade eSDK to 7.1.2 | The AP5020 supports eSDK 7.1.2. |
| HOS-21284 | "RegreSSHion" Vulnerability in OpenSSH | CVE-2024-6387, also known as the "regreSSHion" vulnerability is patched in this release. |
| HOS-21355 | WiFi 6/6E AP: Increase tag entries for HTTP-Post batch reporting | Up to 300 BLE entries are reported per batch interval in HTTP Post. On WiFi 6E APs this feature supports iBeacon and Generic BLE scans. And on WiFi 6 APs this feature supports iBeacon scans only. |
| HOS-21535 | VLAN Counters support on AP5020 | IQ Engine supports the Show Interface Vlan Counters command for AP5020. |
| HOS-21701 | HotSpot 2.0 Configuration In IQ Engine—11ax support | To support the ExtremeCloud IQ Hotspot 2.0 feature, the 802.11ax APs (AP305C/X, AP410C, AP510C/X, AP460C/S6C/S12C) must run IQ Engine 10.7.5, or later. |
| HOS-21829 | Fabric-Attach (Autosense) IQ Engine new Default LLDP Handling (3000/X, AP5010, AP5050) | IQ Engine 10.7.5 enables LLDP by default, for AP3000/X, AP5010, and AP5050U/D models. |
| HOS-21847 | Add Port Description (TLV) to LLDP Neighbor (302W & 6E APs) | The Show lldp neighbor command includes the Port Description field. |
| Issue ID | Description |
|---|---|
| CFD-11844 (02871771) | We resolved an issue where 802.1x authentication would reoccur on Eth0. |
| CFD-12152 (02991956, 02994867, 02995713,02993534, 03007447, 03001635, 03053431) | We resolved an issue where PPSK user authentication failed with incorrect password logs, in 10.7r2 with 802.11r enabled. |
| CFD-12418 (03007758) | We resolved an issue where, under certain conditions, the DCD Daemon was not running and causing errors on the AP5010. |
| CFD-12492 (03004220, 03016826) | We resolved an issue where Fabric Attach configurations were being removed on reboot after save config in sCLI. |
| CFD-12675 (02668167) | We resolved an issue where the CRC firmware check was failing. |
| CFD-12722 (03022452) | We resolved an issue where users were not receiving credentials after registering for the Guest network through the Captive Web Portal. |
| CFD-12747 (02928391) | We resolved an issue where one-way audio occurred on the AP5010. |
| CFD-12756 (02998905, 03051701) | We resolved an issue where Wireshark could not parse gratuitous ARP from AP as an LLC frame. |
| CFD-12869 (03036308) | We resolved an issue where the Logging flash was full of unnecessary logs, making it difficult to troubleshoot other issues. In releases earlier than 10.7.5, SNMP queries such as snmpwalk -c hivecommunity -v 1 10.254.157.99 .1.3.6.1.4.1.26928.1.2.7.0 generated logs similar to ah_dcd: application: handle_ahUptime sec = 1333, msec = 490. |
| CFD-12871 (03036165) | We resolved an issue where, under certain conditions, AP5020s would become unresponsive and performance would degrade. |
| CFD-13093 (02928391) | We resolved an issue where Spectralink VoIP phones displayed an Insufficient Bandwidth message after a roam. |
| HOS-21436, HOS-21437, HOS-21439, HOS-21440, HOS-21441 | We resolved various issues where the enhanced packet capture filters did not work. |
| HOS-21840 | We resolved an issue where Wireless clients disconnected from the AP5020 when packet captures were run. |
| HOS-21941 | We resolved an issue where packet captures were unexpectedly ending at 30 seconds on the AP5020. |