Manual Configuration Example

The following example shows how to manually set up a controlling bridge (CB) with three attached bridge port extenders (BPEs) in a two-tier structure (see CB with Two-Tier BPEs Topology).

Attach BPEs.
On the CB, enable VPEX mode:
```
X465.1 # enable vpex
X465.1 # reboot
Are you sure you want to reboot the switch? (y/N) Yes
Slot-1 VPEX X465.1 #
```
Note
After reboot, command prompt changes to show that you are in VPEX mode.

Create LAGs between CB and first-tier BPEs:

Slot-1 VPEX X465.1 # enable sharing 1:10 group 1:10-1:11 lacp
Slot-1 VPEX X465.2 # enable sharing 1:20 group 1:20-1:21 lacp

Configure slot identifiers associated with the first-tier BPEs:

Slot-1 VPEX X465.1 # configure vpex port 1:10 slot 110
WARNING: This command will remove VLAN membership from the
         port 1:10.
         Do you want to continue? (y/N)Yes

Slot-1 VPEX X465.2 # configure vpex port 1:20 slot 120
WARNING: This command will remove VLAN membership from the
         port 1:20.
         Do you want to continue? (y/N)Yes

Slot-1 VPEX X465.3 # show slot
Slots    Type                 Configured           State       Ports   Flags
--------------------------------------------------------------------------------
Slot-1   X465        X465        Operational   64    M
Slot-110 V400-48p-10GE4                            Operational   52
Slot-120 V400-48p-10GE4                            Operational   52
Flags : M - Backplane link to Master is Active
        B - Backplane link to Backup is also Active
        D - Slot Disabled
        I - Insufficient Power (refer to "show power budget")

Slot-1 VPEX X465.9 # show vpex
Virtual Port Extender: Enabled
Cascade
Port     Slot
=============
1:10     110
1:20     120

Note

Observe that the show slot command shows the CB as slot 1 with the two BPEs as slots 110 and 120.

Note

Observe that the show vpex command shows that ports 1:10 and 1:20 are the cascade ports connecting to the BPEs.

Create LAG between first-tier and second-tier BPEs:
```
Slot-1 VPEX X465.1 # enable sharing 110:49 group 110:49, 110:50 lacp
```

Configure slot identifier associated with the second-tier BPE:

Slot-1 VPEX X465.1 # configure vpex port 110:49 slot 130
WARNING: This command will remove VLAN membership from the
         port 110:49.
         Do you want to continue? (y/N)Yes

Slot-1 VPEX X465.3 # show slot
Slots    Type                 Configured           State       Ports   Flags
--------------------------------------------------------------------------------
Slot-1   X465        X465         Operational   64    M
Slot-110 V400-48p-10GE4                            Operational   52
Slot-120 V400-48p-10GE4                            Operational   52
Slot-130 V400-48p-10GE4                            Operational   52
Flags : M - Backplane link to Master is Active
        B - Backplane link to Backup is also Active
        D - Slot Disabled
        I - Insufficient Power (refer to "show power budget")

Slot-1 VPEX X465.9 # show vpex
Virtual Port Extender: Enabled
Cascade
Port     Slot
=============
1:10     110
1:20     120
110:49   130

Apply Layer 2 configuration:

Slot-1 VPEX X465.1 # configure vlan Default delete port all
Slot-1 VPEX X465.2 # create vlan v100 tag 100
Slot-1 VPEX X465.3 # configure vlan v100 add port 130:1-2, 120:1-2, 1:7 tagged

If required, you can use standard show commands to troubleshoot the network from the CB using the counters:

Slot-1 VPEX X465.3 # show port 130:49-50, 120:49-50, 1:7 statistics no-refresh
Port   Link  Tx Pkt    Tx Byte    Rx Pkt    Rx Byte  Rx Pkt Rx Pkt  Tx Pkt Tx Pkt
       State  Count      Count     Count      Count   Bcast  Mcast   Bcast  Mcast
====== ===== ======= ========== ========= ========== ======= ====== ======= ======
130:1  A   97045942 6209457963         0          0       0      0       0     35
130:2  R          0          0         0          0       0      0       0      0
120:1  A         36       4715  97001731 6206623104       0      0       0     35
120:2  A   95802538 6897726741  95784987 7279063658       0    512       0    697
1:7     A   97045942       4715  97001731 6206623104       0      0       0      0
====== ===== ======== ========= ========= ========== ====== ====== ======= ======
          > in Port indicates Port Display Name truncated past 8 characters
          > in Count indicates value exceeds column width. Use 'wide' option or '0' to clear.
          Link State: A-Active, R-Ready, NP-Port Not Present, L-Loopback

Slot-1 VPEX X465.13 # show port 130:49-50, 120:49-50, 1:7 qosmonitor no-refresh
Port Qos Monitor
Port          QP1       QP2       QP3       QP4       QP5       QP6       QP7       QP8
              Pkt       Pkt       Pkt       Pkt       Pkt       Pkt       Pkt       Pkt
             Xmts      Xmts      Xmts      Xmts      Xmts      Xmts      Xmts      Xmts
========================================================================================
130:49   119682459         0         0         0         0         0         0        45
130:50           0         0         0         0         0         0         0         0
120:49           0         0         0         0         0         0         0        45
120:50   119803233         0         0         0         0         0         0       923
1:7      119803233         0         0         0         0         0         0       923