The following issues were resolved in ExtremeXOS 16.2.3. ExtremeXOS 16.2.3 includes all fixes up to and including ExtremeXOS 11.6.5.3, and earlier, ExtremeXOS 12.0.5, ExtremeXOS 12.1.7, ExtremeXOS 12.2.2-patch1-12, ExtremeXOS 12.3.6, ExtremeXOS 12.4.5, ExtremeXOS 12.5.5, ExtremeXOS 12.6.3, ExtremeXOS 12.6.5, ExtremeXOS 12.7.1, ExtremeXOS 15.1.5, ExtremeXOS 15.2.4, ExtremeXOS 15.3.3, ExtremeXOS 15.4.1, ExtremeXOS 15.5.1, ExtremeXOS 15.5.2, ExtremeXOS 15.6.1, ExtremeXOS 15.6.2, ExtremeXOS 15.7.1, ExtremeXOS 16.1, ExtremeXOS 16.1.2, ExtremeXOS 16.1.3, ExtremeXOS 16.2, and ExtremeXOS 16.2.2. For information about those fixes, see the release notes for the specific release.
Resolved Issues, Platform-Specific, and Feature Change Requests (CRs) in ExtremeXOS 16.2.3
| CR Number | Description |
|---|---|
| General | |
| xos0067463 | Traffic does not distribute across LSPs and LAG after enabling L2VPN sharing feature. |
| xos0052786 | BGP aggregation command demands global unicast addresses (GUA) and does not work with IPv6 unicast addresses. |
| xos0054222 | Unable to add second IPv6 address prefix to the network-zone after adding IPv4 address. |
| xos0064727 |
On DHCPv6 clients, sometimes the IPv6 address is not removed even after disabling
the client, and after rebooting, the IPv6 address is saved and this causes the
client to go into a stopped state with the following error message appearing:
<Erro:vlan.AddIPAddrFail> Failed to add IP addr 8001::4aa6:dd38:9b32:e7b/128 from DHCPv6 to VLAN client, DHCPv6 configured IPv6 address already exist on interface client |
| xos0064806 | Switch session stops responding after configuring SSH2 pre-generated private key with a length greater than 4,064 characters. |
| xos0066590 | In an MLAG peer when its MLAG port is down, the following error appears: "Group <ip> not found for VLAN". |
| xos0067055 | Log message "Process exsshd sends hello too often" appears when SSH is enabled in the switch. |
| xos0067194 | Topology change notification is not generated for the STP domain dot1d mode when there is change in the topology. |
| xos0067203 | Multicast packets are flooded on EAPS-blocked ports after removing and then adding ports configured with PSTAG. |
| xos0064672 | Incorrect state observed for DHCPv6 client when restarting the nettools process or rebooting the switch. |
| xos0064864 |
Switch can go into reboot loop if the length of configured SSH private key is different from the actual key stored in EEPROM. This can happen when you attempt to configure an invalid key or when loading a .cfg file containing an SSH private key from another switch onto a new switch with default setting. To recover, at the console prompt, halt the image loading operation at the bootrom prompt, and then execute config none to bypass loading the configuration file containing the invalid or incorrect SSH private key. Workaround: If you want to use a backup configuration (.cfg) file containing an SSH private key from a different switch, then open the configuration file in any editor and remove the “xos-module-exsshd†configuration lines. Use this edited configuration file for loading onto the new switch, and then enable SSH. |
| xos0066030 | L2PT is not working properly after path switchover in VPWS. |
| xos0066386 | The show configuration commands stops responding and produces an error when there is a loop in the network. |
| xos0066813 | Service VLAN ARP packets are lifted to the CPU during MPLS swap operation when service a VLAN is configured with the IP address of the provider switch. |
| xos0067138 | BFD is not working for IP static multicast route. |
| xos0063856 | On enabling SSH2, switch displays key generation time as approximately 15 minutes whereas it actually takes less than one minute. |
| xos0067328 | If you load a configuration file containing an SSH key length lesser than the actual key size stored in the switch EEPROM, the following message appears during bootup: "Enter passphrase:". |
| xos0063261 | Warning message to "restart process exsshd" should appear when configuring SSH2 key. |
| Summit X480 Series Switches | |
| xos0066630 | In Summit X480 stacking, the LED for stacking port 4 is not lit even when link is active. |
| Summit X670 Series Switches | |
| xos0066991 | In X670V-48T switches, combo ports link up with 100 Mbps speed, which is not supported. |
| BlackDiamond 8800 Series Switches | |
| xos0063558 | With 8900-XL modules acting as PE nodes, traffic destined to VPLS FDB entries is flooded periodically. |
| SummitStack | |
| xos0067253 | IPv4 packets ingressing a non-master stack node can be dropped when the port number of the destination's ARP entry is unknown, such as when the destination is using Network Load Balancing (NLB). |
Print
this page
Email this topic
Feedback
View PDF
Download EPUB