This chapter summarizes the supported limits in ExtremeXOS 30.6.1-Patch1-4.
For more information about licenses, see ExtremeXOS 30.6 Feature License Requirements .
The following tables summarize tested metrics for a variety of features, as measured in a per-system basis unless otherwise noted. These limits may change, but represent the current status. The contents of this table supersede any values mentioned in the ExtremeXOS books.
The scaling and performance information shown in the following tables is provided for the purpose of assisting with network design. It is recommended that network architects and administrators design and manage networks with an appropriate level of network scaling “head room.” The scaling and performance figures provided have been verified using specific network topologies using limited switch configurations. There is no guarantee that the scaling and performance figures shown are applicable to all network topologies and switch configurations and are provided as a realistic estimation only. If you experience scaling and performance characteristics that you feel are sufficiently below what has been documented, contact Extreme Networks technical support for additional assistance.
The route limits shown in the following tables for IPv4 and IPv6 routing protocols are software limits only. The actual hardware limits may be higher or lower than the software limits, based on platform. The hardware limits for specific platforms are specified as "IPv4/IPv6 routes (LPM entries in hardware)" in the following tables.
In the Extended Edge Switching architecture, Layer-2, Layer-3, and multicast packet forwarding and filtering operations take place on the controlling bridge. The controlling bridge switch and attached BPEs (V400 Virtual Port Extenders) constitute a single, extended switch system. Therefore, the Extended Edge Switching system assumes the scale and limits from the specific controlling bridge model (for example, Extended Edge Switching X670-G2 series switches) in use. For applicable limits, see the following tables for the controlling bridge you are using.
The following table shows supported limits for features in the Value Edge License.
| Metric | Product | Limit |
|---|---|---|
| AAA (local)—maximum number of admin and local user accounts. | ExtremeSwitching X435 | 16 |
| Access lists (meters)—maximum number of meters. | ExtremeSwitching X435 | 512 ingress |
| Access lists (policies)—suggested maximum number of lines in a single policy file. | ExtremeSwitching X435 | 300,000 |
| Access lists (policies)—maximum number of rules in a single policy file.a | ExtremeSwitching X435 |
1,024 ingress 0 egress |
| Access lists (slices)—number of ACL slices. | ExtremeSwitching X435 | 8 ingress only |
| ACL Per Port Meters—number of meters supported per port. | ExtremeSwitching X435 | 8 |
| ACL port ranges | ExtremeSwitching X435 | 32 |
| Meters Packets-Per-Second Capable | ExtremeSwitching X435 | Yes |
| AVB (audio video bridging)—maximum number of active streams. | ExtremeSwitching X435 | 512 |
| BOOTP/DHCP relay—maximum number of BOOTP or DHCP servers per virtual router. | ExtremeSwitching X435 | 8 |
| BOOTP/DHCP relay—maximum number of BOOTP or DHCP servers per VLAN. | ExtremeSwitching X435 | 8 |
| BOOTP/DHCP relay—maximum number of DHCPv4/v6 relay agents. | ExtremeSwitching X435 | 30 |
| Connectivity fault management (CFM)—maximum number or CFM domains. | ExtremeSwitching X435 | 8 |
| CFM—maximum number of CFM associations. | ExtremeSwitching X435 | 256 |
| CFM—maximum number of CFM up end points. | ExtremeSwitching X435 | 32 |
| CFM—maximum number of CFM down end points. | ExtremeSwitching X435 | 32 |
| CFM—maximum number of CFM remote end points per up/down end point. | ExtremeSwitching X435 | 2,000 |
| CFM—maximum number of dot1ag ports. | ExtremeSwitching X435 | 128 |
| CFM—maximum number of CFM segments. | ExtremeSwitching X435 | 1,000 |
| CFM—maximum number of MIPs. | ExtremeSwitching X435 | 256 |
| DHCPv6 Prefix Delegation Snooping—Maximum number of DHCPv6 prefix delegation snooped entries. | ExtremeSwitching X435 | 30 (with static routes) |
| DHCP snooping entries—maximum number of DHCP snooping entries. | ExtremeSwitching X435 | 30 |
| Dynamic ACLs—maximum
number of ACLs processed per second. Note: Limits are load-dependent.
|
ExtremeSwitching X435
|
|
| EAPS domains—maximum number of EAPS domains. | ExtremeSwitching X435 | 4 |
| EAPSv1 protected VLANs—maximum number of protected VLANs. | ExtremeSwitching X435 | 1,000 |
| ERPS domains—maximum number of ERPS domains with or without CFM configured. | ExtremeSwitching X435 | 4 |
| ERPSv1 protected VLANs—maximum number of protected VLANs. | ExtremeSwitching X435 | 1,000 |
| ELSM (vlan-ports)—maximum number of VLAN ports. | ExtremeSwitching X435 | 2,000 |
| Forwarding rate—maximum L3 software forwarding rate. | ExtremeSwitching X435 | 9,000 pps |
| FDB (unicast blackhole entries)—maximum number of unicast blackhole FDB entries. | ExtremeSwitching X435 | 16,019 |
| FDB (multicast blackhole entries)—maximum number of multicast blackhole FDB entries. | ExtremeSwitching X435 | 16,384 |
| FDB (maximum L2 entries)—maximum number of MAC addresses. | ExtremeSwitching X435 | 16,384 g |
| FDB (maximum L2 entries)—maximum number of multicast FDB entries. | ExtremeSwitching X435 | 512 |
| Identity management—maximum number of Blacklist entries. | ExtremeSwitching X435 | 512 |
| Identity management—maximum number of Whitelist entries. | ExtremeSwitching X435 | 512 |
| Identity management—maximum number of roles that can be created. | ExtremeSwitching X435 | 64 |
| Identity management—maximum role hierarchy depth allowed. | ExtremeSwitching X435 | 5 |
| Identity management—maximum number of attribute value pairs in a role match criteria. | ExtremeSwitching X435 | 16 |
| Identity management—maximum number of child roles for a role. | ExtremeSwitching X435 | 8 |
| Identity management—maximum number of policies/dynamic ACLs that can be configured per role. | ExtremeSwitching X435 | 8 |
| Identity management—maximum number of LDAP servers that can be configured. | ExtremeSwitching X435 | 8 |
| Identity management—maximum number of Kerberos servers that can be configured. | ExtremeSwitching X435 | 20 |
| Identity management—maximum database memory size. | ExtremeSwitching X435 | 512 |
| Identity
management—recommended number of identities per switch. Note: Number of identities per switch is for a default identity
management database size (512 Kbytes) across all platforms.
|
ExtremeSwitching X435 | 100 |
| Identity
management—recommended number of ACL entries per identity. Note: Number of ACLs per identity, based on system ACL
limitation.
|
ExtremeSwitching X435 | 20 |
| Identity management—maximum number of dynamic ACL entries configured as an individual dynamic rule, or as an ACL entry in a policy file. | ExtremeSwitching X435 | 500 |
| IGMP snooping per VLAN filters—maximum number of VLANs supported in per-VLAN IGMP snooping mode. | ExtremeSwitching X435 | 500 |
| IGMPv2 subscriber—maximum number of IGMPv2 subscribers per port.n | ExtremeSwitching X435 | 2,500 |
| IGMPv2 subscriber—maximum number of IGMPv2 subscribers per switch.n | ExtremeSwitching X435 | 12,500 |
| IGMPv3 maximum source per group—maximum number of source addresses per group. | ExtremeSwitching X435 | 250 |
| IGMPv3 subscriber—maximum number of IGMPv3 subscribers per port.n | ExtremeSwitching X435 | 1,000 |
| IGMPv3 subscriber—maximum number of IGMPv3 subscribers per switch.n | ExtremeSwitching X435 | 10,000 |
| IP ARP entries in
software—maximum number of IP ARP entries in software. Note: Might be limited by hardware capacity of FDB (maximum L2
entries).
|
ExtremeSwitching X435 | 20,424 |
| IPv4 ARP entries in hardware with minimum LPM routes—maximum recommended number of IPv4 ARP entries in hardware, with minimum LPM routes present. Assumes number of IP route reserved entries is 100 or less. | ExtremeSwitching X435 | 509 h |
| IPv4 ARP entries in hardware with maximum LPM routes—maximum recommended number of IPv4 ARP entries in hardware, with maximum LPM routes present. Assumes number of IP route reserved entries is “maximum.” | ExtremeSwitching X435 | 500 h |
| IPv4 remote hosts in hardware with zero LPM routes—maximum recommended number of IPv4 remote hosts (hosts reachable through a gateway) in hardware when LPM routing is not used. Assumes number of IP route reserved entries is 0, and number of IPv4 ARP entries present is 100 or less. | ExtremeSwitching X435 | 3,100 h |
| IPv4 routes—maximum number of static IPv4 routes in software (combination of unicast and multicast routes). | ExtremeSwitching X435 | 32 |
| IPv4 routes (LPM entries in hardware)— number of IPv4 routes in hardware. | ExtremeSwitching X435 | 32 |
| IPv6 addresses on an interface—maximum number of IPv6 addresses on an interface. | ExtremeSwitching X435 | 15 |
| IPv6 addresses on a switch—maximum number of IPv6 addresses on a switch. | ExtremeSwitching X435 | 15 |
| IPv6 host entries in hardware—maximum number of IPv6 neighbor entries in hardware. | ExtremeSwitching X435 | 500 |
| IPv6 routes in software—maximum number of static IPv6 routes in software. | ExtremeSwitching X435 | 16 |
| IPv6 routes (LPM entries in hardware)—maximum number of IPv6 routes in hardware. | ExtremeSwitching X435 | 16 |
| IP router interfaces—maximum number of VLANs performing IPv4 and/or IPv6 routing. Excludes sub-VLANs. | ExtremeSwitching X435 | 30 |
| IP unicast static routes—maximum number of permanent IP unicast routes. | ExtremeSwitching X435 | 32 |
| IP multinetting (secondary IP addresses)—maximum number of secondary IP addresses per VLAN. | ExtremeSwitching X435 | 30 |
| Jumbo frames—maximum size supported for jumbo frames, including the CRC. | ExtremeSwitching X435 | 9,216 |
| Layer-2 IPMC forwarding
caches—(IGMP/MLD/PIM snooping) in mac-vlan mode. Note:
|
ExtremeSwitching X435 | 5,000 |
| Layer-3 IPv4
Multicast—maximum number of <S,G,V> entries installed in the hardware (IP
multicast compression enabled). Note:
|
ExtremeSwitching X435 | 1,500 |
| Layer-3 IPv6
Multicast—maximum number of <S,G,V> entries installed in the hardware (IP
multicast compression enabled). Note:
|
ExtremeSwitching X435 | 700 |
| Load sharing—maximum
number of load sharing groups. Note: The actual number of load-sharing groups that can
be configured is limited by the number of physical ports present in the switch or
SummitStack.
|
ExtremeSwitching X435 | 8 |
| Load sharing—maximum number of ports per load-sharing group. | ExtremeSwitching X435 (standalone only) | 8 |
| Logged messages—maximum number of messages logged locally on the system. | ExtremeSwitching X435 | 20,000 |
| MAC-based security—maximum number of MAC-based security policies. | ExtremeSwitching X435 | 1,024 |
| MAC Locking—Maximum number of MAC locking stations that can be learned on a port. | ExtremeSwitching X435 |
64 (static MAC locking stations) 600 (first arrival MAC locking stations) |
| Meters—maximum number of meters. | ExtremeSwitching X435 | 512 |
| Maximum mirroring instances. | ExtremeSwitching X435 | 1 (egress) |
| Mirroring
(filters)—maximum number of mirroring filters. Note: This is the number of filters across all the active mirroring
instances.
|
ExtremeSwitching X435 | 128 |
| Mirroring, one-to-many
(filters)—maximum number of one-to-many mirroring filters. Note: This is the number of filters across all the active mirroring
instances.
|
ExtremeSwitching X435 | 128 |
| Mirroring, one-to-many (monitor port)—maximum number of one-to-many monitor ports. | ExtremeSwitching X435 | 1 |
| Multicast listener discovery (MLD) snooping per-VLAN filters—maximum number of VLANs supported in per-VLAN MLD snooping mode. | ExtremeSwitching X435 | 63 |
| Multicast listener discovery (MLD)v1 subscribers—maximum number of MLDv1 subscribers per port.n | ExtremeSwitching X435 | 2,500 |
| Multicast listener discovery (MLD)v1 subscribers—maximum number of MLDv1 subscribers per switch.n | ExtremeSwitching X435 | 12,500 |
| Multicast listener discovery (MLD)v2 subscribers—maximum number of MLDv2 subscribers per port.n | ExtremeSwitching X435 | 2,000 |
| Multicast listener discovery (MLD)v2 subscribers—maximum number of MLDv2 subscribers per switch.n | ExtremeSwitching X435 | 10,000 |
| Multicast listener discovery (MLD)v2 maximum source per group—maximum number of source addresses per group. | ExtremeSwitching X435 | 200 |
| Network Login—maximum number of clients being authenticated on MAC-based VLAN enabled ports. | ExtremeSwitching X435 | 1,024 |
| Network Login—maximum number of dynamic VLANs. | ExtremeSwitching X435 | 1,024 |
| Network Login VLAN VSAs—maximum number of VLANs a client can be authenticated on at any given time. | ExtremeSwitching X435 | 10 |
| Network Service Identifiers (NSI)/VLAN mappings—maximum number of VLANs to NSI mappings. | ExtremeSwitching X435 | 94 |
| ONEPolicy Roles/Profiles—maximum number of policy roles/profiles. | ExtremeSwitching X435 | 63 |
| ONEPolicy Rules per Role/Profile—maximum number of rules per role/policy. | ExtremeSwitching X435 |
IPv4 Rules: 128 L2 Rules: 56 |
| ONEPolicy Authenticated Users
per Switch—maximum number of authenticated users per switch with TCI-Overwrite
disabled. Note: The maximum values assume 75% utilization of VLAN-XLATE hash
table.
|
ExtremeSwitching X435 | 192 |
| ONEPolicy Authenticated Users
per Port per Switch— maximum number of authenticated users per port per switch
with TCI overwrite disabled. Note: The maximum values assume 75% utilization of VLAN-XLATE hash
table.
|
ExtremeSwitching X435 | 187 |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—total maximum number of unique permit/deny traffic classification rules types (system/stack). | ExtremeSwitching X435 | 184 |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique IPv4 permit/deny traffic classification rules (typesipsource / ipdest / ipfrag / udpsourceportIP / udpdestportIP / tcpsourceportIP / tcpdestportIP / ipttl / iptos / iptype). | ExtremeSwitching X435 | 128 |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique Layer 2 permit/deny traffic classification rules (ethertype/port). | ExtremeSwitching X435 | 56 |
| Policy-based routing (PBR) redundancy—maximum number of flow-redirects. | ExtremeSwitching X435 | 256o |
| Policy-based routing (PBR) redundancy—maximum number of next hops per each flow-direct. | ExtremeSwitching X435 | 32o |
| Private VLANs—maximum number of subscribers. Assumes a minimum of one port per network and subscriber VLAN. | ExtremeSwitching X435 | 15 |
| Private VLANs—maximum
number of private VLANs with an IP address on the network VLAN. Note: This limit is dependent on the maximum number of private
VLANs in an L2-only environment if the configuration has tagged and translated ports.
|
ExtremeSwitching X435 | 15 |
| Private VLANs—maximum number of private VLANs in an L2-only environment. | ExtremeSwitching X435 | 15 |
| Route policies—suggested maximum number of lines in a route policy file. | ExtremeSwitching X435 | 10,000 |
| Spanning Tree (maximum STPDs)—maximum number of Spanning Tree Domains on port mode EMISTP. | ExtremeSwitching X435 | 16 |
| Spanning Tree
PVST+—maximum number of port mode PVST domains. Note: For all platforms, the maximum number of active ports per PVST
domain depends on the maximum number of spanning tree ports supported on given platform. For
example, ExtremeSwitching X670-G2 supports 256 PVST domains (maximum), and 4,096 STP ports
(maximum), so the maximum number of active ports per PVST domain would be 16 ports (4,096 ÷
256).
|
ExtremeSwitching X435 | 128 |
| Spanning Tree—maximum number of multiple spanning tree instances (MSTI) domains. | ExtremeSwitching X435 | 16 |
| Spanning Tree—maximum
number of VLANs per MSTI. Note: Maximum number of 10 active ports per VLAN when all
100 VLANs are in one MSTI.
|
ExtremeSwitching X435 | 100 |
| Spanning Tree—maximum number of VLANs on all MSTP instances. | ExtremeSwitching X435 | 256 |
| Spanning Tree (802.1d domains)—maximum number of 802.1d domains per port. | ExtremeSwitching X435 | 1 |
| Spanning Tree (number of ports)—maximum number of ports including all Spanning Tree domains. | ExtremeSwitching X435 | 1,024 |
| Spanning Tree (maximum VLANs)—maximum number of STP-protected VLANs (dot1d and dot1w). | ExtremeSwitching X435 | 256 |
| SSH (number of sessions)—maximum number of simultaneous SSH sessions. | ExtremeSwitching X435 | 8 |
| Static MAC multicast FDB entries—maximum number of permanent multicast MAC entries configured into the FDB. | ExtremeSwitching X435 | 1,024 |
| Syslog servers—maximum number of simultaneous Syslog servers that are supported. | ExtremeSwitching X435 | 16 |
| Syslog targets—maximum number of configurable Syslog targets. | ExtremeSwitching X435 | 16 |
| Telnet (number of sessions)—maximum number of simultaneous Telnet sessions. | ExtremeSwitching X435 | 8 |
| Virtual routers—maximum number of user-created virtual routers that can be created on a switch. | ExtremeSwitching X435 | 16 (local-only VRs) |
| Virtual router forwarding
(VRFs)—maximum number of VRFs that can be created on a switch. Note: * Subject to other system limitations.
|
ExtremeSwitching X435 | 16 (local-only VRFs) |
| VLAN aggregation—maximum number of port-VLAN combinations on any one superVLAN and all of its subVLANs. | ExtremeSwitching X435 | 1,000 |
| VLANs—includes all VLANs. | ExtremeSwitching X435 | 4,094 |
| VLANs (Layer 2)—maximum number of Layer 2 VLANs. | ExtremeSwitching X435 | 4,094 |
| VLANs (Layer 3)—maximum number of VLANs performing IPv4 and/or IPv6 routing. Excludes sub-VLANs. | ExtremeSwitching X435 |
IPv4: 30 IPv6: 15 |
| VLANs (maximum active port-based)—maximum active ports per VLAN when 1,000 VLANs are configured with default license. | ExtremeSwitching X435 | 28 |
| VLAN Port Interfaces (VPIF)—maximum number of VLAN port interfaces. | ExtremeSwitching X435 | 38,400 |
| VLANs (maximum active protocol-sensitive filters)—number of simultaneously active protocol filters in the switch. | ExtremeSwitching X435 |
16 |
| VLAN translation—maximum number of translation VLANs. Assumes a minimum of one port per translation and member VLAN. | ExtremeSwitching X435 | 15 |
| VLAN translation—maximum
number of translation VLAN pairs with an IP address on the translation VLAN. Note: This limit is dependent on the maximum number of
translation VLAN pairs in an L2-only environment if the configuration includes tagged and
translated ports.
|
ExtremeSwitching X435 | 15 |
| VLAN translation—maximum number of translation VLAN pairs in an L2-only environment. | ExtremeSwitching X435 | 15 |
| XML requests—maximum
number of XML requests per second. Note: Limits are dependent on load and type of XML request. These
values are dynamic ACL data requests.
|
ExtremeSwitching X435 | 10 with 100 DACLs |
The following table shows supported limits for features in the Edge License.
| Metric | Product | Limit |
|---|---|---|
| AAA (local)—maximum number of admin and local user accounts. | All platforms, except X435 | 16 |
| Access lists (meters)—maximum number of meters. | ExtremeSwitching X620, X440-G2 | 1,024 ingress 256 egress |
| ExtremeSwitching X670-G2, X450-G2, X460-G2 | 1,024 ingress 512 egress |
|
| ExtremeSwitching X870, X690, X590, X465 | 2,048 ingress 512 egress |
|
| ExtremeSwitching X695 | 6,000 ingress 2,000 egress |
|
| Access lists (policies)—suggested maximum number of lines in a single policy file. | All platforms, except X435 | 300,000 |
| Access lists (policies)—maximum number of rules in a single policy file.a | ExtremeSwitching X460-G2, X450-G2, X670-G2 | 4,096 ingress 1,024 egress |
| ExtremeSwitching X620, X440-G2 | 2,048 ingress 512 egress |
|
| ExtremeSwitching X870 | 3,072 ingress 1,024 egress |
|
| ExtremeSwitching X690, X590, X465, X695 | 8,192 ingress 1,024 egress |
|
| Access lists (policies)—maximum number of rules in a single policy file in first stage (VFP). | ExtremeSwitching X450-G2, X460-G2 | 2,048 ingress only |
| ExtremeSwitching X670-G2, X870, X690, X695 | 1,024 ingress only | |
|
ExtremeSwitching X620, X440-G2 |
512 ingress only |
|
| ExtremeSwitching X590, X465 | 2,048 ingress only | |
| Access lists (slices)—number of ACL slices. | ExtremeSwitching X460-G2, X450-G2 | 16 ingress 4 egress |
| ExtremeSwitching X670-G2, X690, X590, X465, X695 | 12 ingress 4 egress |
|
| ExtremeSwitching X440-G2, X620 | 8 ingress 4 egress |
|
| ExtremeSwitching X870 | 4 ingress 4 egress |
|
| Access lists (slices)—number of ACL slices in first stage (VFP). | ExtremeSwitching X450-G2, X460-G2, X670-G2, X465, X620, X440-G2, X870, X690, X590, X695 | 4 ingress only |
| ACL Per Port Meters—number of meters supported per port. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 16 |
| ACL port ranges. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 32 |
| Meters Packets-Per-Second Capable. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | Yes |
| AVB (audio video bridging)—maximum number of active streams. | ExtremeSwitching X450-G2, X460-G2, X620, X440-G2 | 1,024 |
| ExtremeSwitching X670-G2 | 4,096 | |
| ExtremeSwitching X590, X690, X870, X695 | N/A | |
| BFD sessions (Software Mode)—maximum number of BFD sessions. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2, X620, X870, X690, X590, X465, X695 (default timers—1 sec) | 512 |
| ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2, X620, X870, X690, X590, X465, X695 (minimal timers—100 msec) | 10c | |
| BFD IPv4 sessions (Hardware Assisted)—maximum number of IPv4 BFD sessions. | ExtremeSwitching X460-G2, X870, X690, X590, X465, X695 | 900 (PTP not enabled) 425 (PTP enabled) 256 (with 3 ms transmit interval) |
| BFD IPv6 sessions (Hardware Assisted)—maximum number of IPv6 BFD sessions. | ExtremeSwitching X460-G2, X870, X690, X590, X465, X695 | 425 (PTP not enabled) |
| BOOTP/DHCP relay—maximum number of BOOTP or DHCP servers per virtual router. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2 , X465, X620, X870, X690, X590, X695 | 8 |
| BOOTP/DHCP relay—maximum number of BOOTP or DHCP servers per VLAN. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2, X465, X620, X870, X690, X590, X695 | 8 |
| BOOTP/DHCP relay—maximum number of DHCPv4/v6 relay agents | ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2 , X465, X620, X870, X690, X590, X695 | 4,000 |
| Connectivity fault management (CFM)—maximum number or CFM domains. Note: With Advanced Edge license or higher.
|
ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2, X620, X870, X690, X590, X465, X695 | 8 |
| CFM—maximum number of CFM associations. Note: With Advanced Edge license or higher.
|
ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2, X620, X870, X690, X590, X465, X695 | 256 |
| CFM—maximum number of CFM up end points. Note: With Advanced Edge license or higher.
|
ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2, X620, X870, X690, X590, X465, X695 | 32 |
| CFM—maximum number of CFM down end points. Note: With Advanced Edge license or higher.
|
ExtremeSwitching X670-G2, X450-G2, X440-G2, X620, X870, X690, X590, X465, X695 | 32 |
| ExtremeSwitching X460-G2 | 256 (non-load shared ports) 32 (load shared ports) |
|
| CFM—maximum number of CFM remote end points per up/down end point. Note: With Advanced Edge license or higher.
|
ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2, X620, X870, X690, X590, X465, X695 | 2,000 |
| CFM—maximum number of dot1ag ports. Note: With Advanced Edge license or higher.
|
ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2, X620, X870, X690, X590, X465, X695 | 128 |
| CFM—maximum number of CFM segments. Note: With Advanced Edge license or higher.
|
ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2, X620, X870, X690, X590, X465, X695 | 1,000 |
| CFM—maximum number of MIPs. Note: With Advanced Edge license or higher.
|
ExtremeSwitching X460-G2, X670-G2, X450-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 256 |
| CLEAR-Flow—total number of rules supported. The ACL rules plus CLEAR-Flow rules must be less than the total number of supported ACLs. | ExtremeSwitching X460-G2, X670-G2, X450-G2 | 4,094 |
| ExtremeSwitching X440-G2, X620 | 1,024 | |
| ExtremeSwitching X870 | 3,072 | |
| ExtremeSwitching X690, X590, X465, X695 | 8,192 | |
| Data Center Bridging eXchange (DCBX) protocol Type Length Value (TLVs)—maximum number of DCBX application TLVs. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2, X620, X870, X690, X590, X465, X695 | 8 |
| DHCPv6 Prefix Delegation Snooping—Maximum number of DHCPv6 prefix delegation snooped entries. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 256 (with underlying protocol RIPng) 128 (with underlying protocol OSPFv3) 1,024 (with static routes) |
| DHCP snooping entries—maximum number of DHCP snooping entries. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 2,048 |
| Dynamic ACLs—maximum number of ACLs processed per second.
Note: Limits are load-dependent.
|
ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | |
|
|
|
| EAPS domains—maximum number of EAPS domains. Note: An EAPS ring that is being spatially reused cannot have
more than four configured EAPS domains.
Note: You can increase the number of domains by upgrading to the
Advanced Edge license.
|
ExtremeSwitching X670-G2, X450-G2, X460-G2, X440-G2, X620, X870, X690, X590, X465, X695 | 4 |
| EAPSv1 protected VLANs—maximum number of protected VLANs. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2 | 1,000 |
| ExtremeSwitching X870, X690, X590, X465, X695 | 2,000 | |
| ERPS domains—maximum number of ERPS domains with or without CFM
configured. Note: You can increase the number of domains by upgrading to the
Advanced Edge license.
|
ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 4 |
| ERPSv1 protected VLANs—maximum number of protected VLANs. | ExtremeSwitching X870, X690, X590, X465, X695 | 2,000 |
| ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2 | 1,000 | |
| ERPSv2 protected VLANs—maximum number of protected VLANs. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690 , X590, X465, X695 | 2,000 |
| ExtremeSwitchingX620, X440-G2 | 500 | |
| ELSM (vlan-ports)—maximum number of VLAN ports. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X870, X690, X590 , X465, X695 |
5,000 |
| ExtremeSwitching X440-G2 | 4,000 | |
| Extended Edge Switching maximum BPEs—maximum number of attached bridge port extenders (BPEs). | ExtremeSwitching X465, X590, X670-G2, X690 | 48 |
| Extended Edge Switching maximum cascade ports—maximum number of upstream ports on bridge port extenders (BPEs). | ExtremeSwitching X465, X590, X670-G2, X690 |
2 on V400-24 and V300 models 4 on V400-48 models |
| Extended Edge Switching maximum tiers—maximum number of cascade levels (tiers) of bridge port extenders (BPEs). | ExtremeSwitching X465, X590, X670-G2, X690 | 4 (except for V300-8P-2T-W, which support 1 tier) |
| Extended Edge Switching maximum ring BPEs—maximum number of bridge port extenders (BPEs) in a ring topology. | ExtremeSwitching X465, X590, X670-G2, X690 | 8 |
| Extended Edge Switching VLAN+ port memberships—maximum number of VLAN+ (extended) port memberships. | ExtremeSwitching X465, X590, X670-G2, X690 |
12,000 in hash mode (default) 131,000 in port-group mode |
| Forwarding rate—maximum L3 software forwarding rate. | ExtremeSwitching X690, X590, X465, X695 | 30,000 pps |
| ExtremeSwitching X870 | 32,000 pps | |
| ExtremeSwitching X450-G2 | 16,000 pps | |
| ExtremeSwitching X460-G2 | 17,000 pps | |
| ExtremeSwitching X620 | 10,000 pps | |
| ExtremeSwitching X670-G2 | 15,000 pps | |
| ExtremeSwitching X440-G2 | 9,000 pps | |
| FDB (unicast blackhole entries)—maximum number of unicast blackhole FDB entries. | ExtremeSwitching X460-G2 | 49,152f |
| ExtremeSwitching X670-G2 | 294,912f | |
| ExtremeSwitching X450-G2 | 34,816f | |
| ExtremeSwitching X620, X440-G2 | 16,384f | |
| ExtremeSwitching X870 | 139,264f | |
| ExtremeSwitching X690, X590, X465 | 278,528f | |
| ExtremeSwitching X695 | 294,912 f | |
| FDB (multicast blackhole entries)—maximum number of multicast blackhole FDB entries. | ExtremeSwitching X460-G2, X450-G2, X440-G2, X620 | 1,024 |
| ExtremeSwitching X670-G2, X870, X690, X590, X465, X695 | 4,096 | |
| FDB (maximum L2 entries)—maximum number of MAC addresses. | ExtremeSwitching X460-G2 | 98,300g |
| ExtremeSwitching X670-G2 | 294,912g | |
| ExtremeSwitching X450-G2 | 68,000g | |
| ExtremeSwitching X620, X440-G2 | 16,384 | |
| ExtremeSwitching X870 | 139,264g | |
| ExtremeSwitching X690, X590, X465, X695 | 278,528g | |
| ExtremeSwitching X695 | 294,912 g | |
| FDB (maximum L2 entries)—maximum number of multicast FDB entries. | ExtremeSwitching X670-G2, X870, X690, X590, X465, X695 | 4,096 |
| ExtremeSwitching X450-G2, X460-G2, X620, X440-G2 | 1,024 | |
| Identity management—maximum number of Blacklist entries. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 512 |
| Identity management—maximum number of Whitelist entries. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 512 |
| Identity management—maximum number of roles that can be created. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 64 |
| Identity management—maximum role hierarchy depth allowed. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 5 |
| Identity management—maximum number of attribute value pairs in a role match criteria. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 16 |
| Identity management—maximum number of child roles for a role. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 8 |
| Identity management—maximum number of policies/dynamic ACLs that can be configured per role. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 8 |
| Identity management—maximum number of LDAP servers that can be configured. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 8 |
| Identity management—maximum number of Kerberos servers that can be configured. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 20 |
| Identity management—maximum database memory size. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 512 |
| Identity management—recommended number of identities per switch. Note: Number of identities per switch is for a default identity
management database size (512 Kbytes) across all platforms.
|
ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 100 |
| Identity management—recommended number of ACL entries per identity.
Note: Number of ACLs per identity, based on system ACL
limitation.
|
ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 20 |
| Identity management—maximum number of dynamic ACL entries configured as an individual dynamic rule, or as an ACL entry in a policy file. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 500 |
| IGMP snooping per VLAN filters—maximum number of VLANs supported in per-VLAN IGMP snooping mode. | ExtremeSwitching X460-G2, X870 | 1,500 |
| ExtremeSwitching X450-G2 | 2,048 | |
| ExtremeSwitching X670-G2 , X695 | 2,000 | |
| ExtremeSwitching X620, X440-G2 | 1,000 | |
| ExtremeSwitching X690, X590, X465 | 4,000 | |
| IGMPv1/v2 SSM-map entries—maximum number of IGMPv1/v2 SSM mapping entries. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 500 |
| IGMPv1/v2 SSM-map entries—maximum number of sources per group in IGMPv1/v2 SSM mapping entries. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 50 |
| IGMPv2 subscriber—maximum number of IGMPv2 subscribers per port.n | ExtremeSwitching X670-G2, X460-G2, X450-G2 | 4,000 |
| ExtremeSwitching X440-G2, X620 | 3,500 | |
| ExtremeSwitching X870, X690, X590, X465, X695 | 4,000 | |
| IGMPv2 subscriber—maximum number of IGMPv2 subscribers per switch.n | ExtremeSwitching X670-G2 | 30,000 |
| ExtremeSwitching X460-G2, X450-G2 | 20,000 | |
| ExtremeSwitching X620, X440-G2 | 17,500 | |
| ExtremeSwitching X465, X870, X690, X590, X695 | 45,000 | |
| IGMPv3 maximum source per group—maximum number of source addresses per group. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X770, X620, X440-G2, X870, X690, X590, X465, X695 | 250 |
| IGMPv3 subscriber—maximum number of IGMPv3 subscribers per port.n | ExtremeSwitching X670-G2, X460-G2, X450-G2 | 4,000 |
| ExtremeSwitching X440-G2, X620 | 3,500 | |
| ExtremeSwitching X870, X690, X590, X465, X695 | 4,000 | |
| IGMPv3 subscriber—maximum number of IGMPv3 subscribers per switch.n | ExtremeSwitching X460-G2, X450-G2 | 20,000 |
| ExtremeSwitching X670-G2 | 30,000 | |
| ExtremeSwitching X620, X440-G2 | 17,500 | |
| ExtremeSwitching X870, X690, X590, X465, X695 | 45,000 | |
| IP ARP entries
in software—maximum number of IP ARP entries in software. Note: Might be limited by hardware capacity of FDB (maximum L2
entries).
|
ExtremeSwitching X670-G2 | 131,072 (up to)h |
| ExtremeSwitching X460-G2 | 57,344 (up to)h | |
| ExtremeSwitching X450-G2 | 47,000 (up to)h | |
| ExtremeSwitching X440-G2, X620 | 20,480 | |
| ExtremeSwitching X870 | 94,206 (up to)h | |
| ExtremeSwitching X690, X590, X465 | 157,694 (up to) h | |
| ExtremeSwitching X695 | 184,318 (up to) h | |
| IPv4 ARP entries in hardware with minimum LPM routes—maximum recommended number of IPv4 ARP entries in hardware, with minimum LPM routes present. Assumes number of IP route reserved entries is 100 or less. | ExtremeSwitching X870 | 74,000 (up to)h |
| ExtremeSwitching X460-G2 | 50,000 (up to)h | |
| ExtremeSwitching X670-G2 | 108,000 (up to)h | |
| ExtremeSwitching X450-G2 | 39,000 (up to)h | |
| ExtremeSwitching X620 | 1,500 | |
| ExtremeSwitching X440-G2 | 1,000 | |
| ExtremeSwitching X690, X590, X465 | 119,000 (up to) h | |
| ExtremeSwitching X695 | 46,000 (up to) h | |
| IPv4 ARP entries in hardware with maximum LPM routes—maximum recommended number of IPv4 ARP entries in hardware, with maximum LPM routes present. Assumes number of IP route reserved entries is “maximum.” | ExtremeSwitching X870 | 64,000 (up to)h |
| ExtremeSwitching X460-G2 | 43,000 (up to)h | |
| ExtremeSwitching X670-G2 | 98,000 (up to)h | |
| ExtremeSwitching X450-G2 | 29,000 (up to)h | |
| ExtremeSwitching X620 | 1,500 | |
| ExtremeSwitching X440-G2 | 1,000 | |
| ExtremeSwitching X690, X590, X465 | 109,000 (up to) h | |
| ExtremeSwitching X695 | 125,000 (up to) h | |
| IP flow information export (IPFIX)—number of simultaneous flows. | ExtremeSwitching X460-G2 | 2,048 ingress 2,048 egress |
| ExtremeSwitching X450-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | N/A | |
| IPv4 remote hosts in hardware with zero LPM routes—maximum recommended number of IPv4 remote hosts (hosts reachable through a gateway) in hardware when LPM routing is not used. Assumes number of IP route reserved entries is 0, and number of IPv4 ARP entries present is 100 or less. | ExtremeSwitching X870 | 120,000 (up to)h |
| ExtremeSwitching X460-G2 | 73,000h | |
| ExtremeSwitching X670-G2 | 176,000 (up to)h | |
| ExtremeSwitching X450-G2 | 61,000 (up to)h | |
| ExtremeSwitching X440-G2, X620 | 3,500 | |
| ExtremeSwitching X690, X590, X465 | 216,000 (up to) h | |
| ExtremeSwitching X695 | 241,000 (up to) h | |
| IPv4 routes—maximum number of IPv4 routes in software (combination of unicast and multicast routes), including static and from all routing protocols. | ExtremeSwitching X460-G2, X450-G2, X440-G2, X620 | 25,000 |
| ExtremeSwitching X670-G2, X690, X870, X590, X465, X695 | 131,000 | |
| IPv4 routes (LPM entries in hardware)— number of IPv4 routes in hardware. | ExtremeSwitching X460-G2 | 12,000 |
| ExtremeSwitching X450-G2 | 16,000 | |
| ExtremeSwitching X670-G2, X690, X870, X590, X465, X695 | 131,000 q | |
| ExtremeSwitching X620, X440-G2 | 480 | |
| IPv6 6in4 tunnel—maximum number of IPv6 6in4 tunnels. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590, X465, X695 | 255 |
| ExtremeSwitching X440-G2, X620 | N/A | |
| IPv6 6to4 tunnel—maximum number of IPv6 6to4 tunnels. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590, X465, X695 | 1 (per virtual router) |
| ExtremeSwitching X440-G2, X620 | N/A | |
| IPv6 addresses on an interface—maximum number of IPv6 addresses on an interface. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 255 |
| IPv6 addresses on a switch—maximum number of IPv6 addresses on a switch. | ExtremeSwitching X670-G2, X460-G2, X450-G2, X870, X690, X590, X465, X695 | 2,048 |
| ExtremeSwitching X620, X440-G2 | 510 | |
| IPv6 host entries in hardware—maximum number of IPv6 neighbor entries in hardware. | ExtremeSwitching X670-G2 | 36,750h |
| ExtremeSwitching X460-G2 | 22,000h | |
| ExtremeSwitching X450-G2 | 12,000h | |
| ExtremeSwitching X440-G2 | 1,000 | |
| ExtremeSwitching X620 | 1,500 | |
| ExtremeSwitching X690, X590, X465 | 24,500h | |
| ExtremeSwitching X870 | 22,000h | |
| ExtremeSwitching X695 | 57,000 h | |
| IPv6 routes in software—maximum number of IPv6 routes in software, including static routes and routes from all routing protocols. | ExtremeSwitching X450-G2, X460-G2, X620, X440-G2 | 25,000 |
| ExtremeSwitching X670-G2, X690, X870, X590, X465, X695 | 65,000q | |
| IPv6 routes (LPM entries in hardware)—maximum number of IPv6 routes in hardware. | ExtremeSwitching X460-G2 | 6,000 |
| ExtremeSwitching X450-G2 | 8,000 | |
| ExtremeSwitching X670-G2, X690, X870, X590, X465, X695 |
65,000q |
|
| ExtremeSwitching X620, X440-G2 | 240 | |
| IPv6 routes with a mask greater than 64 bits in hardware—maximum number of such IPv6 LPM routes in hardware. | ExtremeSwitching X670-G2, X690, X870, X590, X465, X695 | 8,192r |
| ExtremeSwitching X440-G2, X620 | 1,024 | |
| ExtremeSwitching X450-G2, X460-G2 | 2,048 | |
| IPv6 route sharing in hardware—route mask lengths for which ECMP is supported in hardware. | ExtremeSwitching X460-G2, X450-G2, X620 |
0–64 >64 single path only |
| ExtremeSwitching X670-G2, X690, X870, X590, X465, X695 | 0–128r | |
| ExtremeSwitching X440-G2 | Not supported | |
| IP router interfaces—maximum number of VLANs performing IPv4 and/or IPv6 routing. Excludes sub-VLANs. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X690, X590, X465, X695 | 2,048 |
| ExtremeSwitching X620, X440-G2 | 510 | |
| IP multicast static routes—maximum number of permanent multicast IP routes. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X690, X590, X465, X695 | 1,024 |
| IP unicast static routes—maximum number of permanent IP unicast routes. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X690, X590, X465, X695 | 1,024 |
| ExtremeSwitching X620, X440-G2 | 480 | |
| IP route sharing (maximum gateways)—Configurable maximum number of gateways used by equal cost multipath OSPF, BGP, IS-IS, static routes, or L2VPNs. Static routes, OSPF, and BGP are limited to 64 ECMP gateways per destination, while IS-IS is limited to 8. L2VPNs are limited to 16 LSPs per pseudowire on platforms that support 32 gateways, and 64 LSPs per pseudowire on platforms that support 64 gateways. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X620, X870, X690, X590, X465, X695 | 2, 4, 8, 16, 32, or 64 |
| ExtremeSwitching X440-G2 | N/A | |
| IP route sharing (total combinations of gateway sets)—maximum number of combinations of sets of adjacent gateways used by multipath OSPF, BGP, IS-IS, or static routes. | ExtremeSwitching X670-G2 | |
|
|
|
| ExtremeSwitching X460-G2, X450-G2 | ||
|
|
|
| ExtremeSwitching X620 | ||
|
|
|
| ExtremeSwitching X690, X590, X465, X695 | ||
Note: The values here represent the maximum attainable ECMP
groups of which, due to the RIOT feature, half are reserved for overlay and half for underlay
routing. For more information about RIOT, see the
ExtremeXOS 30.6 User Guide
.
|
|
|
| ExtremeSwitching X870 | ||
|
|
|
| ExtremeSwitching X440-G2 | N/A | |
| IP multinetting (secondary IP addresses)—maximum number of secondary IP addresses per VLAN. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 255 |
| Jumbo frames—maximum size supported for jumbo frames, including the CRC. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 9,216 |
| L2 VPN: VCCV (pseudowire Virtual Circuit Connectivity Verification) VPNs per switch—maximum number of VCCV enabled VPLS VPNs. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465 | 16 |
| ExtremeSwitching X450-G2, X620, X440-G2, X695 | N/A | |
| L2 VPN: VPLS MAC addresses—maximum number of MAC addresses learned by a switch. | ||
| ExtremeSwitching X670-G2, X690, X590, X465 | 140,000 | |
| ExtremeSwitching X460-G2 | 55,000 | |
| ExtremeSwitching X870 | 65,000 | |
| ExtremeSwitching X450-G2, X620, X440-G2, X695 | N/A | |
| L2 VPN: VPLS VPNs—maximum number of VPLS virtual private networks per switch. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465 | 1,023 |
| ExtremeSwitching X450-G2, X620, X440-G2, X695 | N/A | |
| L2 VPN: VPLS peers—maximum number of VPLS peers per VPLS instance. | ExtremeSwitching X670-G2, X460-G2, X870, X690, X590, X465 | 64 |
| ExtremeSwitching X450-G2, X620, X440-G2, X695 | N/A | |
| L2 VPN: LDP pseudowires—maximum number of pseudowires per switch. | ExtremeSwitching X670-G2, X460-G2, X870, X690, X590, X465 | 7,000 |
| ExtremeSwitching X450-G2, X620, X440-G2, X695 | N/A | |
| L2 VPN: static pseudowires—maximum number of static pseudowires per switch. | ExtremeSwitching X670-G2, X460-G2, X870, X690, X590, X465 | 7,000 |
| ExtremeSwitching X450-G2, X620, X440-G2, X695 | N/A | |
| L2 VPN: Virtual Private Wire Service (VPWS) VPNs—maximum number of virtual private networks per switch. | ExtremeSwitching X670-G2, X870, X690, X590, X465 | 4,090 |
| ExtremeSwitching X460-G2 | 1,023 | |
| ExtremeSwitching X450-G2, X620, X440-G2, X695 | N/A | |
| Layer-2 IPMC forwarding caches—(IGMP/MLD/PIM snooping) in
mac-vlan mode. Note:
|
ExtremeSwitching X670-G2, X695 | 73,000 |
| ExtremeSwitching X460-G2 | 24,000 | |
| ExtremeSwitching X450-G2 | 14,000 | |
| ExtremeSwitching X620, X440-G2 | 5,000 | |
| ExtremeSwitching X870 | 36,000 | |
| ExtremeSwitching X690, X590, X465 | 67,000 | |
| Layer-3 IPv4
Multicast—maximum number of <S,G,V> entries installed in the hardware
(IP multicast compression enabled). Note:
|
ExtremeSwitching X460-G2 | 26,000 |
| ExtremeSwitching X450-G2 | 21,000 | |
| ExtremeSwitching X670-G2 | 77,500 | |
| ExtremeSwitching X620, X440-G2 | 1,500 | |
| ExtremeSwitching X870 | 52,000 | |
| ExtremeSwitching X690, X590, X465 | 93,000 | |
| ExtremeSwitching X695 | 104,000 | |
| Layer-3 IPv6
Multicast—maximum number of <S,G,V> entries installed in the hardware
(IP multicast compression enabled). Note:
|
ExtremeSwitching X670-G2 | 30,000 |
| ExtremeSwitching X460-G2 | 14,000 | |
| ExtremeSwitching X450-G2 | 10,000 | |
| ExtremeSwitching X620, X440-G2 | 700 | |
| ExtremeSwitching X870 | 18,000 | |
| ExtremeSwitching X690, X590, X465 | 48,000 | |
| ExtremeSwitching X695 | 52,000 | |
| Load sharing—maximum number of load sharing groups. Note: The actual number of load-sharing groups that can
be configured is limited by the number of physical ports present in the switch or
SummitStack.
|
ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 128 |
| Load sharing—maximum number of ports per load-sharing group. | For standalone and stacked: ExtremeSwitching X620, X440-G2 | 8 |
| For standalone: ExtremeSwitching X670-G2, X460-G2, X450-G2, X870, X690, X590, X465, X695 | 32 | |
| For stacked: ExtremeSwitching X670-G2, X460-G2, X450-G2, X670-G2, X870, X690, X590, X465, X695 | 64 | |
| Logged messages—maximum number of messages logged locally on the system. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 20,000 |
| MAC-based security—maximum number of MAC-based security policies. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 1,024 |
| MAC Locking—Maximum number of MAC locking stations that can be learned on a port. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 |
64 (static MAC locking stations) 600 (first arrival MAC locking stations) |
| Meters—maximum number of meters supported. | ExtremeSwitching X460-G2, X450-G2, X670-G2, X440-G2, X620, X870, X690, X590 , X465, X695 | 2,048 |
| Maximum mirroring instances. | ExtremeSwitching
X450-G2, X460-G2, X670-G2, X870, X690, X590, X465, X695 Note: Only two or four mirroring
instances will be active at a time, depending on the mirroring filter added to it. There are
four hardware resource slots. Each single instance uses one such slot, while each ingress plus
egress instance uses two slots. You can use a total of four slots, while there are no more
than two egress instances. The maximum possible combination for mirroring instances:
|
16 (including default mirroring instance) |
| ExtremeSwitching X620, X440-G2 Note: For stacks containing X620 or X440-G2, maximum supported egress
mirror instances is 1.
|
1 (egress) | |
| Mirroring (filters)—maximum number of mirroring filters. Note: This is the number of filters across all the active mirroring
instances.
|
ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 128 |
| Mirroring, one-to-many (filters)—maximum number of one-to-many mirroring
filters. Note: This is the number of filters across all the active mirroring
instances.
|
ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 128 |
| Mirroring, one-to-many (monitor port)—maximum number of one-to-many monitor ports. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 16 |
| MLAG ports—maximum number of MLAG ports allowed. | ExtremeSwitching X670-G2, X690, X695 | 71 |
| ExtremeSwitching X440-G2, X450-G2 | 51 | |
| ExtremeSwitching X460-G2 | 53 | |
| ExtremeSwitching X620 | 15 | |
| ExtremeSwitching X870 | 127 | |
| ExtremeSwitching X590, | 35 | |
| ExtremeSwitching X465 | 55 | |
| MLAG peers—maximum number of MLAG peers allowed. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 2 |
| MPLS RSVP-TE interfaces—maximum number of interfaces. | ExtremeSwitching X460-G2, X670-G2, X590, X465, X870 | 32 |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| MPLS RSVP-TE ingress LSPs—maximum number of ingress LSPs. | ExtremeSwitching X460-G2, X670-G2, X870, X590,X690, X465 | 2,000 |
| ExtremeSwitching X450-G2, X440-G2, X620 X590, X465 | N/A | |
| MPLS RSVP-TE egress LSPs—maximum number of egress LSPs. | ExtremeSwitching X460-G2, X670-G2, X870, X690 X590, X465 | 2,000 |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| MPLS RSVP-TE transit LSPs—maximum number of transit LSPs. | ExtremeSwitching X460-G2, X670-G2 | 2,000 |
| ExtremeSwitching X870, X690, X590, X465 | 4,000 | |
| ExtremeSwitching X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS RSVP-TE paths—maximum number of paths. | ExtremeSwitching X460-G2 | 1,000 |
| ExtremeSwitching X670-G2, X870, X690, X590, X465 | 2,000 | |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| MPLS RSVP-TE profiles—maximum number of profiles. | ExtremeSwitching X460-G2 | 1,000 |
| ExtremeSwitching X670-G2, X870, X690 X590, X465 | 2,000 | |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| MPLS RSVP-TE EROs—maximum number of EROs per path. | ExtremeSwitching X460-G2, X670-G2, X870, X690 X590, X465 | 64 |
| ExtremeSwitching X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS LDP peers—maximum number of MPLS LDP peers per switch. | ||
| ExtremeSwitching X670-G2, X460-G2, X870, X690 X590, X465 | 128 | |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| MPLS LDP adjacencies—maximum number of MPLS LDP adjacencies per switch. | ExtremeSwitching X460-G2 | 50 |
| ExtremeSwitching X670-G2, X870, X690 X590, X465 | 64 | |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| MPLS LDP ingress LSPs—maximum number of MPLS LSPs that can originate from a switch. | ExtremeSwitching X670-G2, X460-G2, X870, X690 X590, X465 | 2,048 |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| MPLS LDP-enabled interfaces—maximum number of MPLS LDP configured interfaces per switch. | ||
| ExtremeSwitching X670-G2, X460-G2, X870, X690 X590, X465 | 128 | |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| MPLS LDP transit LSPs—maximum number of MPLS transit LSPs per switch. | ExtremeSwitching X670-G2, X460-G2, X870, X690 X590, X465 | 4,000 |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| MPLS LDP egress LSPs—maximum number of MPLS egress LSPs that can terminate on a switch. | ExtremeSwitching X670-G2, X460-G2, X870, X690 X590, X465 | 4,000 |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| MPLS static egress LSPs—maximum number of static egress LSPs. | ExtremeSwitching X460-G2 | 7,116 |
| ExtremeSwitching X870, X690, X590, X465, X670-G2 | 8,000 | |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| MPLS static ingress LSPs—maximum number of static ingress LSPs. | ExtremeSwitching X460-G2, X870, X690 X590, X465 | 4,000 |
| ExtremeSwitching X670-G2 | 2,048 | |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| MPLS static transit LSPs—maximum number of static transit LSPs | ExtremeSwitching X670-G2, X460-G2, X870, X690 X590, X465 | 4,000 |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| Multicast listener discovery (MLD) snooping per-VLAN filters—maximum number of VLANs supported in per-VLAN MLD snooping mode. | ExtremeSwitching X460-G2, X670-G2, X870 | 768 |
| ExtremeSwitching X450-G2 | 508 | |
| ExtremeSwitching X620, X440-G2 | 256 | |
| ExtremeSwitching X690, X590, X465, X695 | 1,500 | |
| Multicast listener discovery (MLD)v1 subscribers—maximum number of MLDv1 subscribers per port.n | ExtremeSwitching X670-G2, X450-G2, X460-G2 | 4,000 |
| ExtremeSwitching X620, X440-G2 | 3,500 | |
| ExtremeSwitching X870, X690, X590, X465, X695 | 4,000 | |
| Multicast listener discovery (MLD)v1 subscribers—maximum number of MLDv1 subscribers per switch.n | ExtremeSwitching X460-G2, X450-G2, X620, X440-G2 | 10,000 |
| ExtremeSwitching X670-G2 | 30,000 | |
| ExtremeSwitching X870, X690, X590, X465, X695 | 45,000 | |
| Multicast listener discovery (MLD)v2 subscribers—maximum number of MLDv2 subscribers per port.n | ExtremeSwitching X670-G2, X460-G2, X450-G2 | 4,000 |
| ExtremeSwitching X620, X440-G2 | 3,500 | |
| ExtremeSwitching X870, X690, X590, X465, X695 | 4,000 | |
| Multicast listener discovery (MLD)v2 subscribers—maximum number of MLDv2 subscribers per switch.n | ExtremeSwitching X670-G2 | 30,000 |
| ExtremeSwitching X460-G2, X450-G2, X620, X440-G2 | 10,000 | |
| ExtremeSwitching X870, X690, X590, X465, X695 | 45,000 | |
| Multicast listener discovery (MLD)v2 maximum source per group—maximum number of source addresses per group. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465 , X695 | 200 |
| Multicast listener discovery (MLD) SSM-map entries—maximum number of MLD SSM mapping entries. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590, X465, X695 | 500 |
| ExtremeSwitching X440-G2, X620 | 50 | |
| Multicast listener discovery (MLD) SSM-MAP entries—maximum number of sources per group in MLD SSM mapping entries. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 50 |
| Network Login—maximum number of clients being authenticated on MAC-based VLAN enabled ports. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 1,024 |
| Network Login—maximum number of clients being authenticated with policy mode enabled with TCI overwrite enabled. | ExtremeSwitching X450-G2, X460-G2, X590, X465 | 1,024 |
| ExtremeSwitching X670-G2, X870, X690, X695 | 512 | |
| ExtremeSwitching X620, X440-G2 | 256 | |
| Network Login—maximum number of dynamic VLANs. | ExtremeSwitching X460-G2, X450-G2, X670-G2, X870, X690, X590, X465, X695 | 2,000 |
| ExtremeSwitching X440-G2, X620 | 1,024 | |
| Network Login VLAN VSAs—maximum number of VLANs a client can be authenticated on at any given time. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 10 |
| Network Service Identifiers (NSI)/VLAN mappings—maximum number of VLANs to NSI mappings. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 94 |
| Node Alias—maximum number of entries per slot. | ExtremeSwitching X450-G2, X460-G2, X670-G2 X620, X440-G2, X870, X690, X590, X465, X695 | 8,192 |
| ONEPolicy Roles/Profiles—maximum number of policy roles/profiles. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 63 |
| ONEPolicy Rules per Role/Profile—maximum number of rules per role/policy. | ExtremeSwitching X450-G2, X460-G2 | IPv6 rules: 256 IPv4 rules: 256 L2 Rules: 184 MAC Rules: 256 |
| ExtremeSwitching X670-G2, X870 | IPv6 Rules: 256 L2 Rules: 184 MAC Rules: 256 IPv4 Rules: 256 |
|
| ExtremeSwitching X620, X440-G2 | IPv6 and Mac Rules: 0 Ipv4 Rules: 256 (per switch) L2 Rules: 184 (per switch) |
|
| ExtremeSwitching X465, X690, X590, X695 |
IPv4 Rules: 512 IPv6 Rules: 512 MAC Rules: 512 L2 Rules: 440 |
|
| ONEPolicy Authenticated Users per Switch—maximum number of authenticated users per switch only with TCI-Overwrite enabled. | ExtremeSwitching X450-G2, X460-G2, X590, X465 | 1,024 |
| ExtremeSwitching X670-G2, X690, X870, X695 | 512 | |
| ExtremeSwitching X620, X440-G2 | 256 | |
| Stacking | Depends on the stack nodes, but the maximum is 65,535. | |
| ONEPolicy Authenticated Users per Switch—maximum number of
authenticated users per switch with TCI-Overwrite disabled. Note: The maximum values assume 75% utilization of VLAN-XLATE hash
table.
|
ExtremeSwitching X690, X590, X465 | 24,576 |
| ExtremeSwitching X670-G2, X460-G2, X870, X695 | 12,288 | |
| ExtremeSwitching X450-G2 | 6,144 | |
| ExtremeSwitching X620, X440-G2 | 1,536 | |
| Stacking | 1,536–65,534 | |
| ONEPolicy Authenticated Users per Port per
Switch— maximum number of authenticated users per port per switch with TCI
overwrite disabled. Note: The maximum values assume 75% utilization of VLAN-XLATE hash
table.
|
ExtremeSwitching X450-G2 | 6,144 |
| ExtremeSwitching X460-G2, X670-G2, X870, X695 | 12,288 | |
| ExtremeSwitching X690, X590, X465 | 24,576 | |
| ExtremeSwitching X440-G2, X620 | 1,536 | |
| ONEPolicy Authenticated Users per Port per Switch— maximum number of authenticated users per port with only with TCI-Overwrite enabled. | ExtremeSwitching X450-G2, X460-G2, X590, X465 | 1,024 |
| ExtremeSwitching X670-G2, X870, X690, X695 | 512 | |
| ExtremeSwitching X620, X440-G2 | 256 | |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—total maximum number of unique permit/deny traffic classification rules types (system/stack). | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870 | 952 |
| ExtremeSwitching X620, X440-G2 | 440 | |
| ExtremeSwitching X690, X590, X465, X695 | 1,976 | |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique MAC permit/deny traffic classification rules types (macsource/macdest). | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870 | 256 |
| ExtremeSwitching X620, X440-G2 | N/A | |
| ExtremeSwitching X690, X590, X465, X695 | 512 | |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique IPv6 permit/deny traffic classification rules types (ipv6dest). | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870 | 256 |
| ExtremeSwitching X620, X440-G2 | N/A | |
| ExtremeSwitching X690, X590, X465, X695 | 512 | |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique IPv4 permit/deny traffic classification rules (typesipsource / ipdest / ipfrag / udpsourceportIP / udpdestportIP / tcpsourceportIP / tcpdestportIP / ipttl / iptos / iptype). | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870 | 256 |
| ExtremeSwitching X690, X590, X465, X695 | 512 | |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique Layer 2 permit/deny traffic classification rules (ethertype/port). | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870 | 184 |
| ExtremeSwitching X620, X440-G2 | 184 | |
| ExtremeSwitching X690, X590, X465, X695 | 440 | |
| Policy-based routing (PBR) redundancy—maximum number of flow-redirects. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590 , X465 , X695 |
256o |
| Policy-based routing (PBR) redundancy—maximum number of next hops per each flow-direct. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590 , X465, X695 |
32o |
| Private VLANs—maximum number of subscribers. Assumes a minimum of one port per network and subscriber VLAN. | ||
| ExtremeSwitching X670-G2 | 63 | |
| ExtremeSwitching X460-G2 | 53 | |
| ExtremeSwitching X450-G2 | 51 | |
| ExtremeSwitching X440-G2 | 47 | |
| ExtremeSwitching X620 | 15 | |
| ExtremeSwitching X870 | 127 | |
| ExtremeSwitching X690, X695 | 71 | |
| ExtremeSwitching X590, X465 | 31 | |
| Private VLANs—maximum number of private VLANs with an IP
address on the network VLAN. Note: This limit is dependent on the maximum number of private
VLANs in an L2-only environment if the configuration has tagged and translated ports.
|
ExtremeSwitching X670-G2, X460-G2, X870, X690, X590, X465, X695 | 1,024 |
| ExtremeSwitching X450-G2 | 510 | |
| ExtremeSwitching X440-G2 | 255 | |
| ExtremeSwitching X620 | 510 | |
| Private VLANs—maximum number of private VLANs in an L2-only environment. | ExtremeSwitching X670-G2, X460-G2, X870, X690, X590, X465, X695 | 1,280 |
| ExtremeSwitching X450-G2 | 597 | |
| ExtremeSwitching X440-G2, X620 | 255 | |
| PTP/1588v2 Clock Ports | ExtremeSwitching X460-G2, X670-G2 | 32 for boundary clock 1 for ordinary clock |
| ExtremeSwitching X440-G2, X465, X620, X870, X690, X590, X695 | N/A | |
| PTP/1588v2 Clock Instances | ExtremeSwitching X670-G2, X460-G2 | 2 combinations:
|
| ExtremeSwitching X440-G2, X465, X620, X870, X690, X590 , X695 | N/A | |
| PTP/1588v2 Unicast Static Slaves | ExtremeSwitching X670-G2, X460-G2 | 40 entries per clock port |
| ExtremeSwitching X440-G2, X465, X620, X870, X690, X590 , X695 | N/A | |
| PTP/1588v2 Unicast Static Masters | ExtremeSwitching X670-G2, X460-G2 | 10 entries per clock type |
| ExtremeSwitching X440-G2, X465, X620, X870, X690, X590, X695 | N/A | |
| Route policies—suggested maximum number of lines in a route policy file. | ExtremeSwitching X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465 , X695 |
10,000 |
| RIP Learned Routes—maximum number of RIP routes supported without aggregation. | ExtremeSwitching X670-G2, X460-G2, X440-G2, X620, X870, X690, X590 , X465 , X695 |
10,000 |
| RIP interfaces on a single router—recommended maximum number of RIP routed interfaces on a switch. | ExtremeSwitching X670-G2, X460-G2, X450-G2, X870, X690, X590 , X465, X695 | 256 |
| ExtremeSwitching X440-G2, X620 | 128 | |
| RIPng learned routes—maximum number of RIPng routes. | ExtremeSwitching X670-G2, X460-G2, X450-G2, X870, X690, X590 , X465, X695 | 3,000 |
| ExtremeSwitching X440-G2, X620 | N/A | |
| Spanning Tree (maximum STPDs)—maximum number of Spanning Tree Domains on port mode EMISTP. | ExtremeSwitching X450-G2, X670-G2, X460-G2, X620, X870, X690, X590 , X465, X695 | 64 |
| ExtremeSwitching X440-G2 | 32 | |
| Spanning Tree PVST+—maximum number of port mode PVST
domains. Note: For all platforms, the maximum number of active ports per PVST
domain depends on the maximum number of spanning tree ports supported on given platform. For
example, ExtremeSwitching X670-G2 supports 256 PVST domains (maximum), and 4,096 STP ports
(maximum), so the maximum number of active ports per PVST domain would be 16 ports (4,096 ÷
256).
|
ExtremeSwitching X670-G2, X620 | 256 |
| ExtremeSwitching X460-G2, X450-G2, X440-G2 | 128 | |
| ExtremeSwitching X870, X690, X590 , X465, X695 | 384 | |
| Spanning Tree—maximum number of multiple spanning tree instances (MSTI) domains. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X870, X690, X590 , X465, X695 | 64 |
| ExtremeSwitching X440-G2 | 32 | |
| Spanning Tree—maximum number of VLANs per MSTI. Note: Maximum number of 10 active ports per VLAN when all
500 VLANs are in one MSTI.
|
ExtremeSwitching X670-G2 | 500 |
| ExtremeSwitching X460-G2, X450-G2, X620, X870, X690, X590 , X465, X695 | 600 | |
| ExtremeSwitching X440-G2 | 256 | |
| Spanning Tree—maximum number of VLANs on all MSTP instances. | ExtremeSwitching X670-G2, X460-G2, X450-G2, X620, X870, X690, X590 , X465, X695 | 1,024 |
| ExtremeSwitching X440-G2 | 512 | |
| Spanning Tree (802.1d domains)—maximum number of 802.1d domains per port. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590 , X465, X695 |
1 |
| Spanning Tree (number of ports)—maximum number of ports including all Spanning Tree domains. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X870, X690, X590, X465, X695 | 4,096 |
| ExtremeSwitching X440-G2 | 2,048 | |
| Spanning Tree (maximum VLANs)—maximum number of STP-protected VLANs (dot1d and dot1w). | ExtremeSwitching X670-G2, X460-G2, X450-G2, X620, X870, X690, X590, X465, X695 | 1,024 |
| ExtremeSwitching X440-G2 | 600 | |
| SSH (number of sessions)—maximum number of simultaneous SSH sessions. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 8 |
| Static MAC multicast FDB entries—maximum number of permanent multicast MAC entries configured into the FDB. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 1,024 |
| Syslog servers—maximum number of simultaneous Syslog servers that are supported. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 16 |
| Syslog targets—maximum number of configurable Syslog targets. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 16 |
| Telnet (number of sessions)—maximum number of simultaneous Telnet sessions. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465 , X695 | 8 |
| Virtual routers—maximum number of user-created virtual routers that can be created on a switch. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X690, X590 , X465, X695 | 63 |
| ExtremeSwitching X440-G2, X620 | 16 (local-only VRs) | |
| Virtual router forwarding (VRFs)—maximum number of VRFs
that can be created on a switch. Note: * Subject to other system limitations.
|
ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X690, X590 , X465, X695 | 960 * |
| ExtremeSwitching X440-G2, X620 | 16 (local-only VRFs) | |
| Virtual router protocols per VR—maximum number of routing protocols per VR. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X690, X590, X465, X695 | 8 |
| ExtremeSwitching X440-G2, X620 | N/A | |
| Virtual router protocols per switch—maximum number of VR protocols per switch. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X690, X590, X465, X695 | 64 |
| ExtremeSwitching X440-G2, X620 | N/A | |
| VLAN aggregation—maximum number of port-VLAN combinations on any one superVLAN and all of its subVLANs. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 1,000 |
| VLANs—includes all VLANs. Note: ExtremeXOS supports only 4,092 user-configurable VLANs.
(VLAN 1 is the default VLAN, and 4,095 is the management VLAN, and you may not configure
them.)
|
ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590 , X465, X695 | 4,094 |
| VLANs (Layer 2)—maximum number of Layer 2 VLANs. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590 , X465, X695 | 4,094 |
| VLANs (Layer 3)—maximum number of VLANs performing IPv4 and/or IPv6 routing. Excludes sub-VLANs. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X690, X590, X465, X695 | 2,048 |
| ExtremeSwitching X440-G2, X620 | 510 | |
| VLAN Port Interfaces (VPIF)—maximum number of VLAN port interfaces. | ExtremeSwitching X440-G2, X450-G2, X460-G2, X465, , X590, X670-G2, X620, X690, X870, X695 | 131,585 |
| VLANs (maximum active port-based)—maximum active ports per VLAN when 4,094 VLANs are configured with the default license. | ExtremeSwitching X670-G2, X870, X690, X590 , X465, X695 | 32 |
| ExtremeSwitching X440-G2 | 28 | |
| ExtremeSwitching X460-G2 | 26 | |
| ExtremeSwitching X620 | 16 | |
| ExtremeSwitching X450-G2 | 29 | |
| ExtremeSwitching X460-G2 | 24 | |
| VLANs (maximum active protocol-sensitive filters)—number of simultaneously active protocol filters in the switch. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2. X870, X690, X590 , X465, X695 |
16 |
| VLAN translation—maximum number of translation VLANs. Assumes a minimum of one port per translation and member VLAN. | ||
| ExtremeSwitching X670-G2 | 63 | |
| ExtremeSwitching X460-G2 | 53 | |
| ExtremeSwitching X450-G2 | 51 | |
| ExtremeSwitching X620 | 15 | |
| ExtremeSwitching X440-G2 | 47 | |
| ExtremeSwitching X870 | 127 | |
| ExtremeSwitching X690, X695 | 71 | |
| ExtremeSwitching X590, X465 | 31 | |
| VLAN translation—maximum number of translation VLAN pairs
with an IP address on the translation VLAN. Note: This limit is dependent on the maximum number of
translation VLAN pairs in an L2-only environment if the configuration includes tagged and
translated ports.
|
ExtremeSwitching X670-G2, X465, X870, X690, X590, X695 | 1,024 |
| ExtremeSwitching X450-G2 | 512 | |
| ExtremeSwitching X620 | 510 | |
| ExtremeSwitching X440-G2 | 255 | |
| VLAN translation—maximum number of translation VLAN pairs in an L2-only environment. | ExtremeSwitching X450-G2, X670-G2, X460-G2, X870, X690, X590, X465, X695 | 2,046 |
| ExtremeSwitching X440-G2, X620 | 255 | |
| XML requests—maximum number of XML requests per second. Note: Limits are dependent on load and type of XML request. These
values are dynamic ACL data requests.
|
ExtremeSwitching X460-G2, X670-G2, X450-G2, X440-G2, X620, X870, X690, X590, X465, X695 | 10 with 100 DACLs |
| XNV authentication—maximum number of VMs that can be processed (combination of local and network VMs). | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 2,048 |
| ExtremeSwitching X450-G2, X440-G2, X620 | 1,024 | |
| XNV database entries—maximum number of VM database entries (combination of local and network VMs). | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 16,000 |
| XNV database entries—maximum number of VPP database entries (combination of local and network VPPs). | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 2,048 |
| XNV dynamic VLAN—Maximum number of dynamic VLANs created (from VPPs /local VMs). | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 2,048 |
| XNV local VPPs—maximum number of XNV local VPPs. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 |
2,048 ingress 512 egress |
| XNV policies/dynamic ACLs—maximum number of policies/dynamic ACLs that can be configured per VPP. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 |
8 ingress 4 egress |
| XNV network VPPs—maximum number of XNV network VPPs.p | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 |
2,048 ingress 512 egress |
The following table shows supported limits for features in the Advanced Edge License.
| Metric | Product | Limit |
|---|---|---|
| BGP auto-peering—maximum number of auto-peering nodes and VTEPs. | ExtremeSwitching X670-G2, X690, X870, X590, X465, X695 | 64 |
| BGP auto-peering attached IPv4 hosts— maximum number of attached IPv4 hosts. | ExtremeSwitching X670-G2 | 16,000 |
| ExtremeSwitching X870, X690, X590, X465, X695 | 64,000 | |
| BGP auto-peering attached IPv6 hosts— maximum number of attached IPv6 hosts. | ExtremeSwitching X670-G2 | 254 |
| ExtremeSwitching X870, X690, X590, X465, X695 | 8,000 | |
| BGP auto-peering
ECMP—maximum number of equal cost multipath for auto-peering. Note: * Subject to the limitation imposed by the number of
physical ports on a switch.
|
ExtremeSwitching X670-G2, ExtremeSwitching X690, X870, X590, X465, X695 | 16* |
| BGP auto-peering maximum IPv4 prefixes with ECMP—Maximum number of IPv4 Network prefixes with ECMP. | ExtremeSwitching X670-G2, ExtremeSwitching X690, X870, X590, X465, X695 | 64,000 |
| BGP auto-peering maximum IPv6 prefixes with ECMP—Maximum number of IPv6 Network prefixes with ECMP. | ExtremeSwitching X670-G2, X690, X870, X590, X465, X695 | 8,000 |
| BGP auto-peering MLAG peers—maximum MLAG peers per AutoBGP node. | ExtremeSwitching X670-G2, X690, X870, X590, X465, X695 | 1 |
| BGP auto-peering VRFs—maximum number of VRFs. | ExtremeSwitching X670-G2, X690, X870, X590, X465, X695 | 64 |
| BGP auto-peering EVPN instances—maximum EVPN instances. | ExtremeSwitching X670-G2, X690, X870, X590, X465, X695 | 1,024 |
| EAPS
domains—maximum number of EAPS domains. Note: An EAPS ring that is being spatially reused cannot have
more than four configured EAPS domains.
|
ExtremeSwitching X870, X690, X590, X465, X695 | 128 |
| ExtremeSwitching X670-G2, X450-G2, X460-G2 | 64 | |
| ExtremeSwitching X440-G2, X620 | 32 | |
| EAPSv2 protected VLANs—maximum number of protected VLANs. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X440-G2, X620 | 500 |
| ExtremeSwitching X870, X690, X590, X465, X695 | 2,000 | |
| ERPS domains—maximum number of ERPS domains without CFM configured. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 32 |
| ERPS domains—maximum number of ERPS domains with CFM configured. | ExtremeSwitching X450-G2, X670-G2, X620, X870, X690, X590, X465, X695 | 16 |
| ExtremeSwitching X460-G2 | 32 | |
| ERPSv1 protected VLANs—maximum number of protected VLANs. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590, X465, X695 | 2,000 |
| ExtremeSwitching X620, X440-G2 | 1,000 | |
| ERPSv2 protected VLANs—maximum number of protected VLANs. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590, X465, X695 | 2,000 |
| ExtremeSwitching X620, X440-G2 | 500 | |
| ESRP groups—maximum number of ESRP groups | ExtremeSwitching X450-G2, X460-G2, X670-G2, X440-G2, X620, X870, X690, X590, X465, X695 | 32 |
| ESRP domains—maximum number of ESRP domains. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 64 |
| ESRP L2 VLANs—maximum number of ESRP VLANs without an IP address configured. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 1,000 |
| ESRP L3 VLANs—maximum number of ESRP VLANs with an IP address configured. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 511 |
| ESRP (maximum ping tracks)—maximum number of ping tracks per VLAN. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 8 |
| ESRP (IP route tracks)—maximum IP route tracks per VLAN. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 8 |
| ESRP (VLAN tracks)—maximum number of VLAN tracks per VLAN. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 1 |
| OSPFv2/v3 ECMP—maximum number of equal cost multipath OSPFv2 and OSPFv3. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X690, X590, X465, X695 | 64 |
| ExtremeSwitching X620 | 4 | |
| ExtremeSwitching X440-G2 | N/A | |
| OSPFv2 areas—as an ABR, how many OSPF areas are supported within the same switch. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 8 |
| ExtremeSwitching X450-G2, X440-G2, X620 | 4 | |
| OSPFv2 external routes—recommended maximum number of external routes contained in an OSPF LSDB. | ExtremeSwitching X870, X690, X590, X465, X695 | 10,000 |
| ExtremeSwitching X670-G2, X460-G2 | 5,000 | |
| ExtremeSwitching X450-G2, X440-G2, X620 | 2,400 | |
| OSPFv2 inter- or intra-area routes—recommended maximum number of inter- or intra-area routes contained in an OSPF LSDB with one ABR in OSPF domain. | ExtremeSwitching X870, X690, X590, X465, X695 | 4,000 |
| ExtremeSwitching X670-G2, X460-G2 | 2,000 | |
| ExtremeSwitching X450-G2, X440-G2, X620 | 1,000 | |
| OSPFv2 interfaces—recommended maximum number of OSPF interfaces on a switch (active interfaces only). | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 4 |
| OSPFv2 links—maximum number of links in the router LSA. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 400 |
| ExtremeSwitching X450-G2, X620, X440-G2 | 4 | |
| OSPFv2 neighbors—maximum number of supported OSPF adjacencies. | ExtremeSwitching X450-G2, X670-G2, X460-G2, X440-G2, X620, X870, X690, X590, X465, X695 | 4 |
| OSPFv2 routers in a single area—recommended maximum number of routers in a single OSPF area. | ExtremeSwitching X870, X690, X590, X465, X695 | 100 |
| ExtremeSwitching X670-G2, X460-G2 | 50 | |
| ExtremeSwitching X450-G2, X440-G2, X620 | 4 | |
| OSPFv2 virtual links—maximum number of supported OSPF virtual links. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 32 |
| ExtremeSwitching X450-G2, X440-G2, X620 | 4 | |
| OSPFv3 areas—as an ABR, the maximum number of supported OSPFv3 areas. | ExtremeSwitching X870, X690, X590, X465, X695 | 100 |
| ExtremeSwitching X460-G2, X670-G2 | 16 | |
| ExtremeSwitching X450-G2, X440-G2, X620 | 4 | |
| OSPFv3 external routes—recommended maximum number of external routes. | ExtremeSwitching X670-G2, X460-G2, X870, X690, X590, X465, X695 | 10,000 |
| ExtremeSwitching X450-G2, X440-G2, X620 | 1,200 | |
| OSPFv3 inter- or intra-area routes—recommended maximum number of inter- or intra-area routes. | ExtremeSwitching X870, X690, X590, X465, X695 | 4.000 |
| ExtremeSwitching X670-G2, X460-G2 | 3,000 | |
| ExtremeSwitching X450-G2, X440-G2, X620 | 500 | |
| OSPFv3 interfaces—maximum number of OSPFv3 interfaces (active interfaces only). | ExtremeSwitching X670-G2, X460-G2, X450-G2, X870, X690, X440-G2, X620, X590, X465, X695 | 4 |
| OSPFv3 neighbors—maximum number of OSPFv3 neighbors. | ExtremeSwitching X450-G2, X670-G2, X460-G2, X870, X690, X440-G2, X620, X590, X465, X695 | 4 |
| OSPFv3 virtual links—maximum number of OSPFv3 virtual links supported. | ExtremeSwitching X670-G2, X460-G2, X870, X690, X590, X465, X695 | 16 |
| ExtremeSwitching X450-G2, X440-G2, X620 | 4 | |
| PIM IPv4 (maximum interfaces)—maximum number of PIM active interfaces. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X440-G2, X620, X690, X590, X465, X695 | 4 |
| PIM IPv4 Limits—maximum number of multicast groups per dynamic rendezvous point. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465 , X695 |
180 |
| PIM IPv4 Limits—maximum number of multicast groups per static rendezvous point. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465 , X695 |
3,000 (depends on policy file limits) |
| PIM IPv4 Limits—maximum number of multicast sources per group. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X690, X590 , X465, X695 | 5,000 |
| ExtremeSwitching X440-G2, X620 | 1,500 | |
| PIM IPv4 Limits—maximum number of dynamic rendezvous points per multicast group. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590 , X465 , X695 |
145 |
| PIM IPv4 Limits—static rendezvous points. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590 , X465 , X695 |
32 |
| PIM IPv6 (maximum interfaces)—maximum number of PIM active interfaces. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X440-G2, X620, X690, X590 , X465, X695 | 4 |
| PIM IPv6 Limits—maximum number of multicast sources per group. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590 , X465, X695 | 1,750 |
| ExtremeSwitching X450-G2 | 1,500 | |
| ExtremeSwitching X440-G2, X620 | 550 | |
| PIM IPv6 Limits—maximum number of multicast groups per dynamic rendezvous point. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465 , X695 |
70 |
| PIM IPv6 Limits—maximum number of multicast groups per static rendezvous point. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465 , X695 |
3,000 (depends on policy file limits) |
| PIM IPv6 Limits—maximum number of dynamic rendezvous points per multicast group. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465 , X695 |
64 |
| PIM IPv6 Limits—maximum number of secondary addresses per interface. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590 , X465 , X695 |
70 |
| PIM IPv6 Limits—static rendezvous points. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590 , X465 , X695 |
32 |
| Port-specific VLAN tags—maximum number of port-specific VLAN tags. | ExtremeSwitching X460-G2, X670-G2, X770, X870, X690, X590 , X465, X695 | 1,023 |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| Port-specific VLAN tags—maximum number of port-specific VLAN tag ports. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 4,000 |
| ExtremeSwitching X450-G2, X440-G2, X620 | N/A | |
| VRRP
(v2/v3-IPv4) (maximum instances)—maximum number of VRRP instances for a single
switch, with Advanced Edge license or higher. Note: These limits are applicable for Fabric Routing
configuration also.
Note: Number of groups configured should not
exceed the number of individual VRs supported (that is, in normal mode) for that platform
type.
|
Normal Mode (as individual VRs): |
|
| ExtremeSwitching X670-G2, X460-G2, X450-G2, X870, X690, X590, X465, X695 | 511 | |
| ExtremeSwitching X440-G2, X620 | 128 | |
|
Scaled Mode (with groups): |
||
| ExtremeSwitching X670-G2, X460-G2, X450-G2, X870, X690, X590, X465, X695 |
2,048 |
|
| ExtremeSwitching X440-G2, X620 | 128 | |
| VRRP (v3-IPv6)
(maximum instances)—maximum number of VRRP instances for a single switch, with
Advanced Edge license or higher. (VRRP-VRRPv3-IPv6) Note: These limits are applicable for Fabric Routing
configuration also.
Note: Number of groups configured should not
exceed the number of individual VRs supported (that is, in normal mode) for that platform
type.
|
Normal Mode (as individual VRs): |
|
| ExtremeSwitching X670-G2, X460-G2, X450-G2, X870, X690, X590, X465, X695 | 511 | |
| ExtremeSwitching X440-G2, X620 | 128 | |
|
Scaled Mode (with groups): |
||
| ExtremeSwitching X670-G2, X460-G2, X450-G2, X870, X690, X590, X465, X695 |
2,048 |
|
| ExtremeSwitching X440-G2, X620 | 128 | |
| VRRP (v2/v3-IPv4/IPv6) (maximum VRID)—maximum number of unique VRID numbers per switch. |
ExtremeSwitching X670-G2, X460-G2, X450-G2 X440-G2, X620, X870, X690, X590, X465, X695 Note: With Advanced Edge license or higher.
|
255 |
| VRRP (v2/v3-IPv4/IPv6) (maximum VRIDs per VLAN)—maximum number of VRIDs per VLAN. |
ExtremeSwitching X670-G2, X460-G2, X450-G2 X440-G2, X620, X870, X690, X590, X465, X695 Note: With Advanced Edge license or higher.
|
255 |
| VRRP (v2/v3-IPv4/IPv6) (maximum ping tracks)—maximum number of ping tracks per VLAN. |
ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 Note: With Advanced Edge license or higher.
|
8 |
| VRRP (maximum ping tracks)—maximum number of ping tracks per VRRP Instance under 128 VRRP instances, with Advanced Edge license or higher. |
ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 |
8 (20 centisecond or 1 second hello interval) |
| VRRP (v3-IPv6) (maximum ping tracks)—maximum number of ping tracks per VRRP Instance under 128 VRRP instances, with Advanced Edge license or higher. |
ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 |
8 (20 centisecond or 1 second hello interval) |
| VRRP (v2/v3-IPv4/IPv6) (maximum iproute tracks)—maximum number of IP route tracks per VLAN. |
ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 |
8 |
| VRRP (v2/v3-IPv4/IPv6)—maximum number of VLAN tracks per VLAN. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X620, X440-G2, X870, X690, X590, X465, X695 | 8 |
| VXLAN—maximum virtual networks. Note: Every VPLS instance/PSTag VLAN reduces this limit by
1.
Note: Assumption is all BUM
(broadcast/unknown-unicast/multicast) FDB entries are pointing to the same set of RTEPs when
all VNETs use explicit flooding. Depends on whether all VNETs use standard or explicit and the
number of tenant VLAN ports.
|
ExtremeSwitching X670-G2, X870, X690, X590, X465, X695 | 2,048–4,000 |
| ExtremeSwitching X460-G2, X450-G2, X440-G2, X620 | N/A | |
| VXLAN—maximum tenant VLANs plus port combinations Note: Every (VPLS/PSTag VLAN) + port reduces the limit by
1.
|
ExtremeSwitching X670-G2, X870, X690, X590, X465, X695 | 4,096 |
| ExtremeSwitching X460-G2, X450-G2, X440-G2, X620 | N/A | |
| VXLAN—maximum static MAC to IP bindings. Note: Every FDB entry configured reduces this limit by 1.
|
ExtremeSwitching X670-G2, X870, X690, X590, X465, X695 | 64,000 |
| ExtremeSwitching X460-G2, X450-G2, X440-G2, X620 | N/A | |
| VXLAN—maximum RTEP IP addresses | ExtremeSwitching X670-G2, X870, X690, X590, X465, X695 | 512 |
| ExtremeSwitching X460-G2, X450-G2, X440-G2, X620 | N/A | |
| VXLAN—maximum virtual networks with dynamic learning and OSPF extensions for VXLAN | ExtremeSwitching X670-G2, X870, X690, X590, X465, X695 | 4,000 |
| ExtremeSwitching X460-G2, X450-G2, X440-G2, X620 | N/A |
The following table shows supported limits for features in the Core License.
| Metric | Product | Limit |
|---|---|---|
| BGP (aggregates)—maximum number of BGP aggregates. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 256 |
| ExtremeSwitching X450-G2 | 204 | |
| BGP (networks)—maximum number of BGP networks. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 1,024 |
| ExtremeSwitching X450-G2 | 820 | |
| BGP
(peers)—maximum number of BGP peers. Note: With default keepalive and hold timers.
Note: Each BGPv4/BGPv6 peer handles a
maximum of 50 routes.
Note: ECMP should not be enabled for
BGP.
|
ExtremeSwitching X460-G2, X670-G2, X870 | 128 |
| ExtremeSwitching , X590, X465, X695 | 300 | |
| ExtremeSwitching X450-G2 | 100 | |
| ExtremeSwitching X690 | 500 | |
| BGP (peer groups)—maximum number of BGP peer groups. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 64 |
| ExtremeSwitching X450-G2 | 50 | |
| BGP (policy entries)—maximum number of BGP policy entries per route policy. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 256 |
| ExtremeSwitching X450-G2 | 204 | |
| BGP (policy statements)—maximum number of BGP policy statements per route policy. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 1,024 |
| ExtremeSwitching X450-G2 | 820 | |
| BGP multicast address-family routes—maximum number of multicast address-family routes. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 25,000 |
| ExtremeSwitching X450-G2 | 20,000 | |
| BGP (unicast address-family routes)—maximum number of unicast address-family routes. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590 , X465 , X695 (at default) | 25,000 |
| ExtremeSwitching X870, X690, X590 , X465 (with ALPM enabled) | 100,000 | |
| ExtremeSwitching X450-G2 | 20,000 | |
| BGP (non-unique routes)—maximum number of non-unique BGP routes. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 25,000 |
| ExtremeSwitching X450-G2 | 20,000 | |
| BGP ECMP—maximum number of equal cost paths per multipath for BGP and BGPv6. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 2, 4, 8, 16, 32, or 64 |
| ExtremeSwitching X450-G2 | 64 | |
| BGPv6 (unicast address-family routes)—maximum number of unicast address family routes. | ExtremeSwitching X460-G2 | 6,000 |
| ExtremeSwitching X670-G2 | 8,000 | |
| ExtremeSwitching X870, X690, X590, X465, X695 | 10,000 | |
| ExtremeSwitching X870, X690 (with ALPM enabled) | 100,000 | |
| ExtremeSwitching X450-G2 | 4,800 | |
| BGPv6 (non-unique routes)—maximum number of non-unique BGP routes. | ExtremeSwitching X460-G2 | 18,000 |
| ExtremeSwitching X670-G2, X870, X690, X590, X465, X695 | 24,000 | |
| ExtremeSwitching X450-G2 | 14,000 | |
| EVPN EVI instances—maximum number of EVI instances. | ExtremeSwitching X670-G2, X870, X690, X590, X465, X695 | 1,024 |
| EVPN LAGs—maximum number of LAGs. | ExtremeSwitching X670-G2, X870, X690, X590, X465, X695 | 128 |
| GRE Tunnels—maximum number of GRE tunnels. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X690, X590, X465 , X695 | 255 |
| ExtremeSwitching X620, X440G2 | N/A | |
| IS-IS adjacencies—maximum number of supported IS-IS adjacencies. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 128 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS ECMP—maximum number of equal cost paths per multipath for IS-IS. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 2, 4, or 8 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS interfaces—maximum number of interfaces that can support IS-IS. | ExtremeSwitching X460-G2, X670-G2, X770, X870, X690, X590, X465, X695 | 255 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS routers in an area—recommended maximum number of IS-IS routers in an area. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 256 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS route origination—recommended maximum number of routes that can be originated by an IS-IS node. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 20,000 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS IPv4 L1 routes in an L1 router—recommended maximum number of IS-IS Level 1 routes in a Level 1 IS-IS router. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 25,000 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS IPv4 L2 routes—recommended maximum number of IS-IS Level 2 routes. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 25,000 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS IPv4 L1 routes in an L1/L2 router—recommended maximum number of IS-IS Level 1 routes in an L1/L2 IS-IS router. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 20,000 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS IPv6 L1 routes in an L1 router—recommended maximum number of IS-IS Level 1 routes in a Level 1 IS-IS router. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 10,000 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS IPv6 L2 routes—recommended maximum number of IS-IS Level 2 routes. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 10,000 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS IPv6 L1 routes in an L1/L2 router—recommended maximum number of IS-IS Level 1 routes in a L1/l2 router. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 10,000 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS IPv4/IPv6 L1 routes in an L1 router—recommended maximum number of IS-IS Level 1 routes in a Level 1 IS-IS router. The numbers documented are based on 50% IPv4 routes and 50% IPv6 routes. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 20,000 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS IPv4/IPv6 L2 routes in an L2 router—recommended maximum number of IS-IS Level 2 routes in a Level 2 IS-IS router. The numbers documented are based on 50% IPv4 routes and 50% IPv6 routes. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 20,000 |
| ExtremeSwitching X450-G2 | N/A | |
| IS-IS IPv4/IPv6 L1 routes in an L1/L2 router—recommended maximum number of IS-IS Level 1 routes in a Level 1/Level2 IS-IS router. The numbers documented are based on 50% IPv4 routes and 50% IPv6 routes. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 20,000 |
| ExtremeSwitching X450-G2 | N/A | |
| MSDP active peers—maximum number of active MSDP peers. | ExtremeSwitching X450-G2, X670-G2, X460-G2, X870, X690, X590, X465, X695 | 64 |
| MSDP SA cache entries—maximum number of entries in SA cache. | ExtremeSwitching X670-G2, X690, X590, X465, X695 | 14,000 |
| ExtremeSwitching X460-G2 | 10,000 | |
| ExtremeSwitching X870 | 11,000 | |
| ExtremeSwitching X450-G2 | 8,000 | |
| MSDP maximum mesh groups—maximum number of MSDP mesh groups. | ExtremeSwitching X450-G2, X670-G2, X460-G2, X870, X690, X590, X465, X695 | 16 |
| OSPFv2/v3 ECMP—maximum number of equal cost multipath OSPFv2 and OSPFv3. | ExtremeSwitching X460-G2, X670-G2, X450-G2, X870, X690, X590, X465, X695 | 64 |
| OSPFv2 areas—as an ABR, how many OSPF areas are supported within the same switch. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590, X465, X695 | 8 |
| OSPFv2 external routes—recommended maximum number of external routes contained in an OSPF LSDB. | ExtremeSwitching X870, X690, X590, X465, X695 | 10,000 |
| ExtremeSwitching X670-G2, X460-G2 | 5,000 | |
| ExtremeSwitching X450-G2 | 4,000 | |
| OSPFv2 inter- or intra-area routes—recommended maximum number of inter- or intra-area routes contained in an OSPF LSDB with one ABR in OSPF domain. | ExtremeSwitching X870, X690, X590, X465, X695 | 4,000 |
| ExtremeSwitching X670-G2, X460-G2 | 2,000 | |
| ExtremeSwitching X450-G2 | 1,600 | |
| OSPFv2 interfaces—recommended maximum number of OSPF interfaces on a switch (active interfaces only). | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 400 |
| ExtremeSwitching X450-G2 | 320 | |
| OSPFv2 links—maximum number of links in the router LSA. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 400 |
| ExtremeSwitching X450-G2 | 320 | |
| OSPFv2 neighbors—maximum number of supported OSPF adjacencies. | ExtremeSwitching X670-G2, X460-G2, X870, X690, X590, X465, X695 | 128 |
| ExtremeSwitching X450-G2 | 96 | |
| OSPFv2 routers in a single area—recommended maximum number of routers in a single OSPF area. | ExtremeSwitching X870, X690, X590, X465, X695 | 100 |
| ExtremeSwitching X670-G2, X460-G2 | 50 | |
| ExtremeSwitching X450-G2 | 40 | |
| OSPFv2 virtual links—maximum number of supported OSPF virtual links. | ExtremeSwitching X460-G2, X670-G2, X870, X690, X590, X465, X695 | 32 |
| ExtremeSwitching X450-G2 | 25 | |
| OSPFv3 areas—as an ABR, the maximum number of supported OSPFv3 areas. | ExtremeSwitching X870, X690, X590, X465, X695 | 100 |
| ExtremeSwitching X460-G2, X670-G2 | 16 | |
| ExtremeSwitching X450-G2 | 12 | |
| OSPFv3 external routes—recommended maximum number of external routes. | ExtremeSwitching X670-G2, X460-G2, X870, X690, X590, X465, X695 | 10,000 |
| ExtremeSwitching X450-G2 | 7,500 | |
| OSPFv3 inter- or intra-area routes—recommended maximum number of inter- or intra-area routes. | ExtremeSwitching X870, X690, X590, X465, X695 | 4.000 |
| ExtremeSwitching X670-G2, X460-G2 | 3,000 | |
| ExtremeSwitching X450-G2 | 500 | |
| OSPFv3 interfaces—maximum number of OSPFv3 interfaces (active interfaces only). | ||
| ExtremeSwitching X670-G2, X460-G2, X870, X690, X590, X465, X695 | 256 | |
| ExtremeSwitching X450-G2 | 192 | |
| OSPFv3 neighbors—maximum number of OSPFv3 neighbors. | ExtremeSwitching X670-G2, X460-G2, X870, X690, X590, X465, X695 | 64 |
| ExtremeSwitching X450-G2 | 48 | |
| OSPFv3 virtual links—maximum number of OSPFv3 virtual links supported. | ExtremeSwitching X670-G2, X460-G2, X870, X690, X590, X465, X695 | 16 |
| ExtremeSwitching X450-G2 | 12 | |
| PIM IPv4 (maximum interfaces)—maximum number of PIM active interfaces. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590, X465, X695 | 255 |
| PIM IPv4 Limits—maximum number of multicast groups per dynamic rendezvous point. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590 , X465, X695 | 180 |
| PIM IPv4 Limits—maximum number of multicast groups per static rendezvous point. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590, X465, X695 | 3,000 (depends on policy file limits) |
| PIM IPv4 Limits—maximum number of multicast sources per group. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590 , X465, X695 | 5,000 |
| PIM IPv4 Limits—maximum number of dynamic rendezvous points per multicast group. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590 , X465, X695 | 145 |
| PIM IPv4 Limits—static rendezvous points. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590 , X465, X695 | 32 |
| PIM IPv6 (maximum interfaces)—maximum number of PIM active interfaces. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590 , X465, X695 | 255 |
| PIM IPv6 Limits—maximum number of multicast sources per group. |
ExtremeSwitching X460-G2, X670-G2, X870, X690, X590 , X465, X695 |
1,750 |
| ExtremeSwitching X450-G2, | 1,500 | |
| PIM IPv6 Limits—maximum number of multicast groups per dynamic rendezvous point. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590 , X465, X695 |
70 |
| PIM IPv6 Limits—maximum number of multicast groups per static rendezvous point. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590, X465, X695 |
3,000 (depends on policy file limits) |
| PIM IPv6 Limits—maximum number of dynamic rendezvous points per multicast group. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590 , X465, X695 | 64 |
| PIM IPv6 Limits—maximum number of secondary addresses per interface. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590 , X465, X695 | 70 |
| PIM IPv6 Limits—static rendezvous points. | ExtremeSwitching X450-G2, X460-G2, X670-G2, X870, X690, X590 , X465, X695 | 32 |