efa inventory device setting update

Configures device settings such as maintenance mode.

Syntax

efa inventory device setting update [ --ip device-ips| --fabric fabric-name | --maint-mode-enable-on-reboot { Yes | No } --maint-mode-enable { Yes | No } --health-check-enable { Yes | No } --health-check-interval minutes| --health-check-heartbeat-miss-threshold { 2 | 3 | 4 | 5 } --config-backup-periodic-enable { Yes | No } --config-backup-interval interval | --number-of-config-backups count | --mct-bring-up-delay delay | --maint-mode-convergence-time time |--prefix-independent-convergence { Yes | No } | --prefix-independent-convergence-static { Yes | No } |--maximum-load-sharing-paths { 8 | 16 | 32 | 64 | 128 } | --maximum-ipv6-prefix-length-64 strimg | --urpf string | --ip-option-disable { Yes | No } | --ip-option-disable-cpu { Yes | No } | --ipv6-option-disable { Yes | No } |-h, --help ]

Parameters

--ip device-ips: Specifies a comma-separated range of device IP addresses. For example:
10.1.1.13,10.1.1.50,10.1.1.101.
--fabric fabric-name: Specify the name of the fabric.
--maint-mode-enable-on-reboot { Yes | No }: Specify Yes to activate maintenance mode on reboot and No to deactivate it.
--maint-mode-enable { Yes | No }: Specify Yes to activate maintenance mode and No to deactivate it.
--health-check-enable { Yes | No }: Specify Yes to enable health check and No to disable it.
--health-check-interval minutes: Specifies the health check interval in minutes. Valid values are 6m through 24h. Default is 6m.
--health-check-heartbeat-miss-threshold { 2 | 3 | 4 | 5 }: Specifies the health check miss threshold.
--config-backup-periodic-enable { Yes | No }: Specify Yes to enable periodic configuration backup and No to disable it.
--config-backup-interval interval: Specifies configuration backup interval, in minutes. Valid values are 3m through 30h. The default is 24h.
--number-of-config-backups count: Specifies configuration backup count. Valid values are 2-20. The default is 4.
--mct-bring-up-delay delay: Specifies delay, in seconds, before an MCT cluster bring up. Valid values are 10-600. Default is 90. Set a value of 0 to deconfigure.
--maint-mode-convergence-time time: Specifies the maximum time, in seconds, that maintenance mode is allowed to complete operations. Valid values are 100-500. Default is 300. Set a value of 0 to deconfigure.
--prefix-independent-convergence { Yes | No }: Specify Yes to enable BGP PIC and No to de-configure it.
--prefix-independent-convergence-static { Yes | No }: Specify Yes to enable Static PIC and No to de-configure it.
--maximum-load-sharing-paths string: Specifies the route load-sharing maximum paths. Valid values are 8,16,32,64,128, and 0 to deconfigure.
--maximum-ipv6-prefix-length-64 string: Enter Yes to configure the maximum route prefix length of 64. This configuration is applicable for Extreme 8820, 8720, 8520 hardware.
--urpf string: Enter Yes to configure the maximum route prefix length of 64 along with unicast reverse path forwarding. This configuration is applicable for Extreme 8820, 8720, 8520 hardware.
-h, --help: Help for update.
--ip-option-disable { Yes | No }: Enter Yes to disable processing IP packets with ip options. Enter No to enable processing IP packets with ip options.
--ip-option-disable-cpu { Yes | No }: Enter Yes to disable processing IP packets with IP options destined to the CPU. Enter No to enable processing IP packets with IP options destined to the CPU.
--ipv6-option-disable { Yes | No }: Enter Yes to disable processing IPV6 packets with IP options. Enter No to enable processing IPV6 packets with IP options. This parameter is not supported on SLX9540 and SLC9640.

Examples

This example specifies a delay of 200 seconds before an MCT cluster bring up.

$ efa inventory device setting update –-ip 10.20.24.10 
–-mct-bring-up-delay 200

This example specifies a maximum time of 100 seconds that maintenance mode is allowed to complete operations.

$ efa inventory device setting update –-ip 10.20.24.10 
–-maint-mode-convergence-time 100

This example enables prefix independent convergence on the device.

efa inventory device setting update –-ip 10.20.24.10 --prefix-independent-convergence
Yes					
Warning: The best practice is to clear all routes after configuring PIC. You can also reload the device.
Execute the CLI to clear : efa inventory device clear route-all –-ip 10.20.24.1

This example enables prefix independent convergence static on the device.

efa inventory device setting update --ip 10.20.24.18 --prefix-independent-convergence-static yes
+--------------+--------------------------------+---------+-------+-------+
|  IP ADDRESS  |              NAME              | STATUS  | VALUE | ERROR |
+--------------+--------------------------------+---------+-------+-------+
| 10.20.24.18 | Static Prefix Independent      | Success | Yes   |       |
|              | Convergence Enabled            |         |       |       |
+--------------+--------------------------------+---------+-------+-------+
Warning: The best practice is to clear all routes after configuring Static PIC. You can also reload the device.
Execute the CLI to clear : efa inventory device clear route-all --ip 10.20.24.18
Execute the CLI to reload : efa inventory device reload --ip 10.20.24.18

This example configures the maximum route prefix length of 64.

efa inventory device setting update –-ip 10.24.80.135 --maximum-ipv6-prefix-length-64 
Warning: Configuration will not take effect until reloaded. 
Execute the CLI to reload : efa inventory device reload –-ip 10.24.80.135

This example specifies disabling ip option processing and disabling ipv6 option processing while allowing ip option processing destined to the cpu.

efa inventory device setting update --ip 10.10.10.1 --ip-option-disable yes 
--ip-option-disable-cpu no --ipv6-option-disable yes
+---------------+-----------------------+------------+-------------+-------------+
| IP ADDRESS    |      NAME             | STATUS     |  VALUE      | ERROR       |
+---------------+-----------------------+------------+-------------+-------------+
| 10.24.2.120   | ip-option-disable     | Success    | Yes         |             |
|               +-----------------------+------------+-------------+-------------+
|               | ip-option-disable-cpu | Success    | No          |             |
|               +-----------------------+------------+-------------+-------------+
|               | ipv6-option-disable   | Success    | Yes         |             |
+---------------+-----------------------+------------+-------------+-------------+