The following issues were resolved in ExtremeXOS 22.6. ExtremeXOS 22.5 includes all fixes up to and including ExtremeXOS 11.6.5.3, and earlier, ExtremeXOS 12.0.5, ExtremeXOS 12.1.7, ExtremeXOS 12.2.2-patch1-12, ExtremeXOS 12.3.6, ExtremeXOS 12.4.5, ExtremeXOS 12.5.5, ExtremeXOS 12.6.3, ExtremeXOS 12.6.5, ExtremeXOS 12.7.1, ExtremeXOS 15.1.5, ExtremeXOS 15.2.4, ExtremeXOS 15.3.3, ExtremeXOS 15.4.1, ExtremeXOS 15.5.1, ExtremeXOS 15.5.2, ExtremeXOS 15.6.1, ExtremeXOS 15.6.2, ExtremeXOS 15.7.1, ExtremeXOS 16.1, ExtremeXOS 16.1.2, ExtremeXOS 16.1.3, ExtremeXOS 21.1, ExtremeXOS 22.1, ExtremeXOS 22.2, ExtremeXOS 22.3, ExtremeXOS 22.4, and ExtremeXOS 22.5. For information about those fixes, see the release notes for the specific release.
Resolved Issues, Platform-Specific, and Feature Change Requests (CRs) in 22.6
| CR Number | Description |
|---|---|
| Summit X460-G2 Series Switches | |
| xos0070774 | On Summit X460-G2 series switches, packets are not transmitted out of the VIM-2t or VIM-2x ports configured for 1G speed after rebooting. |
| ExtremeSwitching X690 Series Switches | |
| xos0071292 | Mirroring does not work on ExtremeSwitching X690 series switches when an optic is inserted into the intended mirroring port, port is configured as 'mirror-to', and then cable is inserted into the port. |
| xos0071325 | Multicast packets with TTL value 1 traffic is flooded on ExtremeSwitching X690 series switches. |
| xos0071996 | On ExtremeSwitching X690 series switches, need to be able to program in Extended View IP adjacencies learned on VXLAN tunnels. |
| xos0072069 | A Few L3VPN routes are not reachable after several LSP flap events. |
| xos0070629 | When auto-peering is enabled, disabling the network port over which a VXLAN tunnel egresses may cause the error "exvlan: configPortLearningState..." to appear. |
| xos0072619 | On ExtremeSwitching X690 series switches with Extended Edge Switching topology, when using Captive Portal with a high load of simultaneous incoming new users, crashes can occur. |
| xos0072695 | The following EMS log message may occur if a large number of ECMP routes whose
nexthops are reachable using a VXLAN tunnel transition to non-ECMP routes:
<Warn:Card.IPv4FIB.LPMTblAlrdyEmpty> Number of IPv4 routes in LPM table is already 0. |
| ExtremeSwitching X440-G2 Series Switches | |
| xos0072030 | The output of the show power command shows a random, impossible value for the power usage for ExtremeSwitching X440-G2 series switches. |
| xos0072408 | 10G combo ports lose connection after applying quad 10G license. |
| General | |
| xos0061504 | Port-based sharing algorithm incorrectly allows adding greater than 16 member ports in a single group. The maximum number of member ports in single group should be 16. |
| xos0066243 | The eject memorycard command does not properly disconnect memory cards (USB drives) when executed while downloading files by TFTP. |
| xos0071222 | Need a mechanism to suppress generation of IGMP-triggered queries when receiving STP topology changes. |
| xos0071387 | In the ExtremeXOS User Guide Routing Policies chapter, a note regarding "tag" match condition needs to be updated. |
| xos0071430 | XMLC process ends unexpectedly with signal 6 randomly when deleting xml-notification target. |
| xos0071450 | In the output of show ports command, the usual expression for excluding “0” entries is not working as expected. |
| xos0071532 | EDP process ends unexpectedly with signal 6 when receiving EDP packets with zero length on the TLV. |
| xos0071554 | Port group configuration is not retained after save and reboot. |
| xos0071607 | Memory leak for process hal occurs after executing command debug hal show forwarding distribution. |
| xos0071632 | The command show nodealias ports all does not return entries for all ports when two consecutive ports have LAG configuration. |
| xos0071654 | Process netTools stops responding when CNAME record is present. |
| xos0071745 | Multicast packets are dropped for some sources when the route to the source network changes. |
| xos0071761 | User processes created using the create process command always run on VR-MGMT and not on VR-Default even if this is specified while creating the process. |
| xos0071788 | The output of the show configuration/show configuration detail commands does not show management port related traps configuration. |
| xos0071822 | Policy manager cannot configure flood groups when the rate-limit is already configured through CLI. |
| xos0071869 | PIM register policy allows unpermitted group address packets when the source is in the permitted list. |
| xos0071912 | When using "ipaddress" keyword for DHCP option 78, the DHCP ACK is sent with an incorrect value. |
| xos0071973 | Port partition does not take effect after restoring configuration. |
| xos0071990 | Command history buffer should be cleared when users log out. |
| xos0072169 | CLI should restrict configuring IPv6 addresses on network and subscriber VLANs in PVLAN/VLAN aggregation. |
| xos0072209 | RADIUS/TACACS configurations are lost after rebooting if the VLAN interface gets IP address from DHCP server. |
| xos0064251 | TACACS CLI authorization is not working in Chalet. |
| xos0070982 | When using Chalet to access a switch, a spike in thttpd process utilization and slow web performance occurs. |
| xos0071272 | Python script that uses expect functionality never returns to command prompt after executing. |
| xos0072371 | After LACP fallback is enabled with configured timeout, port is added to an aggregator with additional 2 seconds delay. |
| xos0072399 | When using "ipaddress" keyword for DHCP options (42, 6), the DHCP ACK is sent with an incorrect value. |
| xos0072510 | UDP profile with VLAN action does not work when VLAN names are entered in a case-insensitive manner. |
| ACL | |
| xos0071686 | Nettools process ends unexpectedly with signal 11 when the same policy is applied as user ACL and UDP profile. |
| xos0071862 | Need match condition to filter OSPF packet types. |
| AVB | |
| xos0068199 | The AVB protocols provide limited EMS log messages for troubleshooting and debugging. |
| BGP | |
| xos0070899 | Incorrect flag appears in BGP flap statistics table. Even after reaching the maximum of three flaps the output of the show bgp neighbor flap-statistics command shows that it is still in history. |
| xos0072485 | The command enable bgp neighbor neighbor IP remove-private-AS-number is not removing 32-bit private AS-numbers. |
| BGP Auto-peering | |
| xos0072662 | With EasyLAG being active, when EasyLAG links are disabled, and then re-enabled, the link dual-homed to a non-BGP Auto-peering device may remain in the up state incorrectly resulting in black holing of the packets. |
| EDP | |
| xos0072552 | EDP process signal 11 crash occurs when sending CDP packet without port-id. |
| ESRP | |
| xos0071402 | After failover, ESRP slave state does not change to ESRP master. |
| Extended Edge Switching | |
| xos0071631 | With Extended Edge
Switching topology and 600 IPv6 VLANs, executing the command
reboot slot produces the following
errors:<Erro:HAL.LAG.CfgFail> Slot-1: Failed to configure link aggregation group 100:17 on slot 1 unit 0: Invalid parameter
<Erro:HAL.LAG.CfgFail> Slot-1: Failed to configure link aggregation group 100:17 on slot 1 unit 0: Invalid parameter
<Erro:HAL.LAG.CfgFail> Slot-1: Failed to configure link aggregation group 100:17 on slot 1 unit 0: Invalid parameter
<Erro:HAL.LAG.CfgFail> Slot-1: Failed to configure link aggregation group 100:17 on slot 1 unit 0: Invalid parameter
|
| xos0071840 | In a MLAG-Extended Edge Switching setup with a physical loop created between extended ports and with ELRP enabled, the CSP session goes down. |
| xos0072139 | The controlling bridge produces the following error when creating 100 IPv6 VLANs
on peer switch with maximum-gateways set to
32:<Noti:Card.IPv6Adj.Notice> Slot-1: vrId 131074 adj fe80::4:96ff:fe99:ede8: Del: Invalid DOT1BR LAG id -1072 for TGID 0 |
| xos0072214 | In MLAG scaled configuration, with broadcast traffic flowing between CB and extended ports, ISC link flaps may cause tier 2,3, and 4 BPEs CSP sessions to go down. BPEs do not recover automatically. |
| xos0072245 | Add support to configure ping success for ESRP track-ping. |
| xos0072296 | Rate limiting applied on extended ports belonging to different native cascade ports is incorrectly set to native cascade ports too. |
| xos0072161 | The MAC address entries hardware table incorrectly shows 90% utilized even though the number of FDB entries present in Extended Edge-enabled switches is considerably less. |
| xos0072297 | Auth-override is not flushing any authenticated MAC and is enabled for all sessions on a port. |
| Fabric Attach | |
| xos0072457 | When a Fabric Attach (FA) server specifies a management VLAN, the ExtremeXOS FA proxy creates the VLAN if necessary, but does not add FA client ports to the management VLAN. When creating a static VLAN to be used as the FA management VLAN, you must explicitly specify a VLAN tag. If a tag is not specified, ExtremeXOS assigns one to the named VLAN, but the tag value may change. |
| xos0072495 | When creating a static VLAN to be used as the FA management VLAN, it is important to explicitly specify a VLAN tag. If a tag is not specified, ExtremeXOS assigns one to the named VLAN, but the tag value may change. |
| LAG | |
| xos0071603 | Port display string does not appear in output of commands if port is LAG master. |
| Mirroring | |
| xos0072104 | If the VLAN tag is used to add a VLAN to a mirror, then the mirroring configuration output in the command show configuration does not appear properly. |
| xos0072373 | In the output of the show mirror command, maximum supported egress instance should be updated to 1 for ExtremeSwitching X440-G2 and X620 series switches. |
| MPLS | |
| xos0071135 | Service VMAN packets are being forwarded in slowpath after deleting VPLS instance. |
| xos0071728 | A few MPLS LSPs remain in down state after several link flap events in LSP path. |
| xos0072170 | Traffic drops when "egress cep filtering" is enabled on a VPLS service VMAN sharing port. |
| xos0072253 | LSP takes a longer time (320 seconds) to switch over from primary path (strict) to secondary path (dynamic). |
| xos0072617 | Memory leak occur in MPLS process when accessing ExtremePwLspOutboundMappingEntry and ExtremePwPerfEntry SNMP OID |
| OSPF | |
| xos0071613 | RIP routes that are exported as OSPF external routes are advertised by the ASBR even after the routes are removed from routing table. |
| Policy | |
| xos0070491 | etsysMultiAuthSystemCurrentNumUsers=1.3.6.1.4.1.5624.1.2.46.1.1.3 may incorrectly report a non-zero count when policy is disabled. |
| xos0072609 | Dot1p to QoSprofile mapping may not be reflected in ONEpolicy rule when pushing ONEPolicy configuration from ExtremeManagement. |
| xos0072663 | Under a continuous high traffic load, clients on a newly configured port/VLAN combination may not be learned in the filter database (FDB). |
| PTP | |
| xos0071026 | Mirroring of Transmitted GPTP packets is not working. |
| Security | |
| xos0070675 | Dot1X guest VLAN functionality is not working on NetLogin Dot1x-enabled LAG ports. |
| xos0070676 | Dot1x client remains authenticated and is not moved to guest VLAN from destination VLAN even though EAPOL packets were not received from the Dot1x client. |
| xos0070761 | MAC locking limit should be applied to NetLogin-enabled ports. |
| xos0070889 | NetLogin users are authenticated to random destinations when destination VLAN attributes from the RADIUS server are not received. |
| xos0071872 | Netlogin process ends unexpectedly with signal 11 when processing multiple web authentication requests from the same client. |
| xos0072175 | PSTAG configurations are not removed properly after enabling policy on a switch. |
| xos0072208 | Web-based NetLogin does not work if the supplied URL contains keywords such as "login", "hello", etc. |
| xos0072233 | When using a static uplink VLAN, OnePolicy admin-profile macsource rule allows all MAC traffic irrespective of the configured macsource. |
| xos0072558 | MacLockingMacViolation traps are sent periodically with NetLogin enabled. |
| xos0072725 | When the command clear netlogin state port 45 agent dot1x is run, all agents on the port are cleared instead of the specified agent. |
| xos0072790 | Cannot log on using SSH with an user account named as "root". |
| xos0069772 | When sending traffic over an MLAG with NetLogin enabled, FDB and NetLogin sessions are properly checkpointed initially. However, after session timer expiry, the FDB entries are not properly checkpointed between peers and mismatching FDB and NetLogin session states occur. |
| SNMP | |
| xos0070265 | Need MIB access to configure port speed and duplex behavior. |
| xos0071947 | MIB extremeVlanL2statsPktsToCpu is present in the MIB definitions, but does not retrieve the l2stats values of interfaces. |
| xos0072267 | SNMP users created by scripts and saved from another switch do not work. |
| xos0072538 | Query of MIB object extremeSlotModuleInsertedType returns incorrect value for ExtremeSwitching X440-G2-12p/t-10GE4 switches. |
| xos0070961 | Broadcast SNMP get/set-requests are processed by switches even though no IP address is configured on any VLANs. |
| xos0072532 | SNMP process ends unexpected with signal 11 when switch tries to delete the trap receiver from the inactive queue, but the trap receiver is already deleted from the queue by SNMP. |
| Stacking | |
| xos0066163 | Stacking configuration changes on standby nodes can sometimes fail. |
| xos0071891 | EPM crash occurs if an unknown file (does not exist) is specified in the command create process test python-module filename start auto. |
| xos0066008 | Random slots or whole stack reboots when one of the standby nodes in the stack is power cycled with sys-recovery-level configured as "shutdown". |
| STP | |
| xos0071418 | Ports configured for BPDU restriction are re-enabled on recovery-timeout even if administratively disabled. |
| xos0071768 | With two connected switches with one running ExtremeXOS and one running EOS, MSTI information is omitted from STP BPDUs sent by the ExtremeXOS switches. |
| xos0071965 | ExtremeXOS switches send BPDUs with sender Bridge-ID when EOS switches are the root. |
| xos0071982 | Need command to send own switch MAC as bridge ID in STP BPDU. |
| xos0072563 | STP loop protect stays in "Forwarding" state instead of "Listening" state even though it did not receive any BPDU from peer device. |
| VRRP | |
| xos0072116 | Telnet/SSH connections to an IP interface fail when there is continuous traffic to a VRRP virtual IP address. |
| xos0072698 | VRRP crash occurs when host mobility is configured and new host routes are learned continuously. |
| VXLAN | |
| xos0071203 | Though support for ECMP in overlay is present in 22.5, it is not officially supported until ExtremeXOS 22.6. |
Print
this page
Email this topic
Feedback
View PDF
Download EPUB