VSP 4900 Series Hardware

Table 1. Switch models

Model

Initial release

Supported new VOSS feature release

8.9

8.10

 8.10.1 9.0 9.0.2

VSP4900-48P

8.1

 Y

Y

Y

Y

 Y

VSP4900-12MXU-12XE

8.1.5

 Y

Y

Y

Y

 Y

VSP4900-24S

8.1.5

 Y

Y

Y

Y

 Y

VSP4900-24XE

8.1.5

 Y

Y

Y

Y

 Y
Note

Note

Ensure the switch runs, at a minimum, the noted initial software release before you install a VIM.

Table 2. Versatile Interface Modules (VIM)

Model

Initial release

Supported new VOSS feature release

8.9

8.10

 8.10.1 9.0 9.0.2

VIM5-4X

8.1

 Y

Y

Y

Y

 Y

VIM5-4XE

8.1

 Y

Y

Y

Y

 Y

VIM5-2Y

8.1

 Y

Y

Y

Y

 Y

VIM5-4YE

8.1

 Y

Y

Y

Y

 Y

VIM5-2Q

8.1

 Y

Y

Y

Y

 Y
VIM5-4Y

8.1.5

 Y

Y

Y

Y

 Y

VSP 4900 Series Operational Notes

VSP4900-24S fixed ports operate at 1 Gbps. If you connect a 10 Gbps DAC/SFP+ to a VSP4900-24S 1 Gbps fixed port, the system displays the following error message:

10Gb optical module inserted in 1Gb only port nn. Not supported.

Although the link successfully comes up, the operational speed shows as 10 Gbps instead of 1 Gbps. This scenario occurs when a 10 Gbps DAC/SFP+ is used to make any of the following connections from a VSP4900-24S 1 Gbps fixed port:

Versatile Interface Module Operational Notes

The following table summarizes the operational capabilities of the various VIMs:

Table 3. VSP 4900 Series VIM Matrix
VIM5-4X VIM5-4XE VIM5-2Y VIM5-4YE VIM5-4Y VIM5-2Q

Number of supported ports for VSP4900-48P and VSP4900-24S

4

4

2

2

2

1

Number of supported ports for VSP4900-24XE and VSP4900-12MXU-12XE

4

4

2

4

4

2
Port speeds

1 Gbps

10 Gbps

1 Gbps

10 Gbps

10 Gbps or 25 Gbps

All ports must operate at either 10 Gbps or 25 Gbps (default)

10 Gbps or 25 Gbps

All ports must operate at either 10 Gbps or 25 Gbps (default)

10 Gbps or 25 Gbps

All ports must operate at either 10 Gbps or 25 Gbps (default)

40 Gbps

10 Gbps (with channelization
PHY present No Yes Yes Yes Yes No
Copper transceiver support (1 Gbps/10 Gbps) 10GBASE-T only Both 10GBASE-T only 10GBASE-T only 10GBASE-T only Not applicable
MACsec Not supported 128/256 bit Not supported 128/256 bit Not supported Not supported
Forward Error Correction (FEC) Not supported Not supported Not supported

Default is Auto-FEC - FEC Auto, CL108, CL91, CL74 and No FEC supported

Not supported Not supported
1 Gbps Auto-Negotiation Disabled Enabled Not applicable Not applicable Not applicable Not applicable
10 Gbps Auto-Negotiation Disabled Disabled Disabled Disabled Disabled Not applicable
25 Gbps Auto-Negotiation Not applicable Not applicable Disabled

Enabled for DACs

Disabled for AOCs, optical transceivers

 Disabled Not applicable
Note:

Auto-Negotiation values are automatically set based on the type of transceiver detected.

VIM5-2Y and VIM5-4Y Operational Notes

Note

Note

VIM5-2Y and VIM5-4Y are in end-of-sale status.

The IEEE 802.3by requirement for 25 G is that any transceiver or DAC 3 meters or longer, requires the use of forward error correction (FEC). Because the VIM5-2Y and VIM5-4Y do not support FEC, note the following considerations for proper operation with these VIMs:

You might experience CRC or link flap errors by using an unsupported 25 G transceiver.

9037801-01 Rev AC