The following defects were resolved in ExtremeCloud Orchestrator 3.3.0.
| Parent Defect ID: | XCO-3458 | Issue ID: | XCO-3458 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | EFA 3.1.0 |
| Symptom: | Port breakout fails for SLX devices with "generic message error". On device new split ports are created. | ||
| Recovery: |
Login to SLX CLI and remove the breakout of port using the following steps: Run following commands: configuration terminal hardware connector <slot/interface> breakout mode <4x10g/4x25g> no breakout e.g. if the port 0/50 got this issue, following are the commands to run after login to CLI Freedom7-Bng# configure t Entering configuration mode terminal Freedom7-Bng(config)# hardware Freedom7-Bng(config-hardware)# connector 0/50 Freedom7-Bng(config-connector-0/50)# breakout mode 4x10 Freedom7-Bng(config-connector-0/50)# no breakout |
||
| Parent Defect ID: | XCO-3472 | Issue ID: | XCO-3472 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | EFA 3.1.0 |
| Symptom: | XCO IP/VIP change is not updated on device for telemetry/streaming and syslog | ||
| Condition: | Once XCO is installed and devices are discovered in Visibility installation, if the XCO node IP/VIP changes, those are not updated on device for receiving the statistics and syslog. | ||
| Workaround: | Change XCO's IP/VIP before discovering the devices. | ||
| Recovery: | Required to delete and add all devices again after the IP/VIP of XCO is changed. | ||
| Parent Defect ID: | XCO-4180 | Issue ID: | XCO-4180 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | EFA 3.0.0 |
| Symptom: | Http Login/Logout Raslogs repeatedly observed on device side, after CLI execution. | ||
| Condition: | During Ntp create/delete operation, few repeated logs are observed on device. | ||
| Workaround: |
On device side we can configure Raslog to suppress/Ignore logs. logging raslog message SEC-1206 suppress //to supress logging raslog console CRITICAL //to discard other types and show only critical |
||
| Recovery: | It is a non-functional issue and has no impact on the overall system operations. | ||
| Parent Defect ID: | XCO-5931 | Issue ID: | XCO-5931 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | EFA 3.0.1 |
| Symptom: | Firmware Not Committed" but "Firmware Download Show Overall Status" shows "Device Update In Progress | ||
| Condition: |
For the firmware download workflow, it will perform the FWDL on each device as prescribed by the grouping and then finally do a "quick" device update (device links only) for all devices that have participated in the FWDL. The purpose of the device links only update is to ensure the fabric configurations are in-sync after the FWDL workflow has completed since devices were rebooted to activate the new firmware. In this customer case they only did a FWDL of a single device, but the workflow is the same... a device links only update will be performed at the end. The firmware download show command contains the individual device's status in the table and the "Overall Status" at the bottom reflects EFA's overall status of the FWDL workflow which includes the Device links only update. |
||
| Workaround: | The user must poll for the Overall Status Completion to proceed for another FWDL workflow prepare/execute. | ||
| Recovery: | Not applicable. | ||
| Parent Defect ID: | XCO-6192 | Issue ID: | XCO-6192 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | EFA 3.0.0 |
| Symptom: | Unable to login to XCO. | ||
| Parent Defect ID: | XCO-6429 | Issue ID: | XCO-6429 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | EFA 3.1.1 |
| Symptom: | ACL hits displayed on stats table while it should maintain its position during stats update | ||
| Condition: | ACL hits dynamically keep moving around and it can't track of hits. | ||
| Workaround: | Sequence number is implemented and rest of the things will be fixed in next release. | ||
| Parent Defect ID: | XCO-6466 | Issue ID: | XCO-6466 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | EFA 3.1.1 |
| Symptom: | Full IPv4/IPv6 address are not seen for policy rules. | ||
| Condition: | When user launch troubleshoot and monitor page to select the rules. | ||
| Workaround: | Mouse over tip is provided so that user can get the complete address. | ||
| Recovery: | NA | ||
| Parent Defect ID: | XCO-6510 | Issue ID: | XCO-6510 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | XCO 3.2.0 |
| Symptom: | The "Network Essentials" option is listed as a device action for the NPB device and a blank page is opened when the user clicks on that. | ||
| Condition: | NPB device is discovered in XCO and user clicks on the device action (for the NPB device) from the inventory page. | ||
| Workaround: | Do not select the networks essentials for NPB devices from device inventory page. | ||
| Parent Defect ID: | XCO-6629 | Issue ID: | XCO-6629 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | XCO 3.2.0 |
| Symptom: | Cannot scroll to see more than 37 rows while in troubleshooting/monitor in XCO Packet skill version 3.2.0. | ||
| Parent Defect ID: | XCO-6792 | Issue ID: | XCO-6792 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | XCO 3.2.0 |
| Symptom: | XCO doesn't recover after OOB management network failure simulation - double fault testing | ||
| Parent Defect ID: | XCO-6937 | Issue ID: | XCO-6937 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | XCO 3.2.0 |
| Symptom: | Monitor/Troubleshooting page, could not scroll through tables to view an entire table | ||
| Parent Defect ID: | XCO-6950 | Issue ID: | XCO-6950 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | EFA 3.1.0 |
| Symptom: | [Packet Broker] 9920 - The 'Interface Name' field on the Ingress Policy Stats Table does not appear to be working. No information available! | ||
| Parent Defect ID: | XCO-7097 | Issue ID: | XCO-7097 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | XCO 3.2.0 |
| Symptom: | XCO 3.2.0 inventory-service crashing during ‘efa fabric device add-bulk‘ | ||
| Parent Defect ID: | XCO-7223 | Issue ID: | XCO-7223 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | EFA 3.0.1 |
| Symptom: | After upgrade, SLX 9250 Spine2 stuck in failed state when executed "efa inventory drift-reconcile". | ||
| Parent Defect ID: | XCO-7345 | Issue ID: | XCO-7345 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | EFA 3.1.0 |
| Symptom: | insecuretls flags in XCO-3.1.0, it sets the value to true by default and by setting “–insecuretls false”. | ||
| Parent Defect ID: | XCO-7718 | Issue ID: | XCO-7718 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | EFA 2.7.2 |
| Symptom: | drifted configuration on EFA is still showing as drifted after tenant drift reconcile | ||
| Parent Defect ID: | XCO-7797 | Issue ID: | XCO-7797 |
|---|---|---|---|
| Product: | XCO | Reported in Release: | XCO 3.2.1 |
| Symptom: | Certificate expiry notification persists after renewal. | ||