ipv6 route
Configures an IPv6 static route.
Syntax
ipv6 route
dest-ipv6-prefix/prefix-length
next-hop-ipv6-address
[
metric
]
[
distance
number
]
[
tag
tag-number
]
ipv6 route
dest-ipv6-prefix/prefix-length
link-local-next-hop-ipv6-address
[ ethernet
slot/port
]
[
metric
]
[
distance
number
]
[
tag
tag-number
]
ipv6 route
dest-ipv6-prefix/prefix-length
link-local-next-hop-ipv6-address
[port-channel
number
]
[
metric
]
[
distance
number
]
[
tag
tag-number
]
ipv6 route
dest-ipv6-prefix/prefix-length
link-local-next-hop-ipv6-address
[
ve
ve-id
]
[
metric
]
[
distance
number
]
[
tag
tag-number
]
ipv6 route
next-hop-recursion
no ipv6 route
dest-ipv6-prefix/prefix-length
next-hop-ipv6-address
no ipv6 route
dest-ipv6-prefix/prefix-length
link-local-next-hop-ipv6-address
[ ethernet
slot/port
]
no ipv6 route
dest-ipv6-prefix/prefix-length
link-local-next-hop-ipv6-address
[port-channel
number
]
no ipv6 route
dest-ipv6-prefix/prefix-length
link-local-next-hop-ipv6-address
[
ve
ve-id
]
no ipv6 route
next-hop-recursion
Command Default
No IPv6 static route is configured by default.
Parameters
-
dest-ipv6-prefix
- Destination IPv6 prefix in hexadecimal with 16-bit values between colons, as specified in RFC 2373.
-
prefix-length
- A decimal value specifying the length of the IPv6 address prefix.
-
next-hop-ipv6-address
- IPv6 address of the next-hop gateway.
-
link-local-next-hop-ipv6-address
- IPv6 address of the link-local next-hop gateway.
-
ethernet
slot/port
- Specifies the Ethernet slot and port.
- port-channel
number
- Specifies a port-channel interface.
-
ve
ve-id
- Specifies the virtual Ethernet (VE) interface.
-
metric
- Specifies a value that the Layer 3 switch uses to compare this route to other static routes in the IPv6 static route table that have the same destination. The metric applies only to routes that the Layer 3 switch has already placed in the IPv6 static route table. Two or more routes to the same destination with the same metric will load share (as in ECMP load sharing). The range is from 1 through 16. The default is 1.
-
distance
number
- Specifies an administrative distance. The range is from 1 through 254. The default is 1. This is a value that the Layer 3 switch uses to compare this route with routes from other route sources that have the same destination. By default, static routes take precedence over routes learned by routing protocols. To choose a dynamic route over a static route, configure the static route with a higher administrative distance than the dynamic route. A distance of 255 is considered unreachable.
-
tag
- Specifies a tag value for the route. The route tag can be used for route redistribution to routing protocols by means of route maps (as in IPv4 static route redistribution).
- tag-number
- A number from 0 through 4294967295. The default is 0.
- next-hop-recursion
- Specifies that if the next hop for a static route is reachable, then that
route is added to the routing table.
Modes
Global configuration mode
VRF configuration mode
Usage Guidelines
Use the
no form of the command with the same parameters to remove the IPv6 static route.
Examples
The following example creates an IPv6 static route for a destination network with the prefix 2001:DB8::0/32 and a next-hop gateway with the global address 2001:DB8:0:ee44::1.
device# configure terminal
device(config)# ipv6 route 2001:DB8::0/32 2001:DB8:0:ee44::1
The following example configures non-recursive lookup in the default VRF.
device(config)# ipv6 route next-hop-recursion
The following example configures non-recursive lookup in a non-default VRF named
red.
device(config)# vrf red
device(config-vrf-red)# address-family ipv6 unicast
device(config-vrf-red-ipv6-unicast)# ipv6 route next-hop-recursion
