snmp-server v3host
Specifies the host recipient for SNMPv3
trap notification.
Syntax
snmp-server v3host
{
ipv4_host
|
ipv6_host
|
dns_host
}
user_name
[
notifytype
{
traps
|
informs
}
]
[
engineid
engine-id
]
[
udp-port
port_number
]
[
severity-level
|
{
none
|
debug
|
info
|
warning
|
error
|
critical
}
]
[
use-vrf
{
vrf-name}
]
[
source-interface
{
loopback
|
management
{
chassis-ip
|
mgmt-ip
}
|
ve
]
no snmp-server
v3host
{
ipv4_host
|
ipv6_host
|
dns_host
}
user_name
[
notifytype
{traps
|
informs}]
[
engineid
engine-id
]
[
udp-port
port_number
]
[
severity-level
|
{none
|
debug
|
info
|
warning
|
error
|
critical
}
]
[
use-vrf
]
[
source-interface
{
loopback
|
management
{
chassis-ip
|
mgmt-ip
}
|
ve
]
Parameters
-
ipv4_host
|
ipv6_host
|
dns_host
-
Specifies the IP address of the host. IPv4, IPv6, and DNS hosts are supported.
-
user_name
-
Specifies the SNMPv3 user name to be associated with the SNMPv3 host entry.
- notifytype
traps
|
informs
- Specifies the type of notification traps that are sent for the host. Traps and informs are supported. The default notify type is traps.
- engineID
engine-id
- Configures the remote engine ID to receive informs on a remote host.
- udp-port
port_number
- Specifies the UDP port of the host. The default UDP port number is 162.
- severity-level
{
none
|
debug
|
info
|
warning
|
error
|
critical
}
- Provides the ability to filter traps based on severity level on both the host and the SNMPv3 host. Only RASLog (swEvent) traps can be filtered based on severity level. The configured severity level marks the reporting threshold. All messages with the configured severity or higher are displayed. If the severity level of None is specified, all traps are filtered and no RASLog traps are received. The default severity level is none.
-
use-vrf
vrf-name
-
Configures SNMP to use the specified VRF to communicate with the host. The default is mgmt-vrf.
- source-interface
{
loopback
|
management
{
chassis-ip
|
mgmt-ip
}
|
ve
- Specifies whether to use a loopback, management, or VE interface as a source
address for notifications. For management, specifies the chassis or
management IP address.
Modes
Global configuration mode
Usage Guidelines
You can associate a global SNMPv3 host only
with global SNMPv3 users and the local SNMPv3 host only with local SNMPv3 users. You
cannot create a SNMPv3 host by associating with the local SNMPv3 users and vice
versa.
The no form of the command can be used to remove the following
entities: notifytype, engineID,
udp-port, severity-level, and
use-vrf.
Examples
The following example creates an entry for SNMPv3 trap IPv4 host 10.23.23.45 associated with SNMP user "snmpadmin1."
device(config)# snmp-server v3host 10.23.23.45 snmpadmin1 severity-level info
The following example creates an entry for SNMPv3 trap IPv6 host 1050:0:0:0:5:600:300c:326b associated with SNMP user "snmpadmin2." The trap host receives SNMPv3 traps from the configured device.
device(config)# snmp-server v3host 1050::5:600:300c:326b snmpadmin2 severity-level Info
The following example associates the default-vrf VRF for a trap host recipient.
device(config)# snmp-server v3host 10.24.61.10 public use-vrf default-vrf
The following example removes the SNMP v3
host.
device(config)# no snmp-server v3host 10.24.61.10 public
