efa fabric setting

Parameters

--name fabric-name

Specifies the name of the fabric.

--p2p-link-range ip-pool

Specifies the IP address pool used for P2P link configuration.

--loopback-ip-range ip-pool

Specifies the IP address pool used for P2P link configuration.

--rack-l3-backup-ip-range ip-pool

Specifies the IP address pool for Layer 3 backup.

--loopback-port-number id

Specifies the loopback ID on the device to be used as the donor IP interface for the link between leaf and spine. Valid values range from 1 through 255.

--vtep-loopback-port-number id

Specifies the loopback ID on the device to be used as a VTEP IP interface. Valid values range from 1 through 255.

--spine-asn-block asn-pool

Specifies the ASN pool for spine nodes or one ASN.

--super-spine-asn-block asn

Specifies one ASN.

--leaf-asn-block asn-pool

Specifies the ASN pool for leaf nodes.

--border-leaf-asn-block asn-pool

Specifies the ASN pool for border leaf nodes.

--rack-asn-block asn pool

Specifies the ASN pool for rack nodes. Valid values are numbers from 4200000000 through 4200065534.

--rack-border-leaf-asn-block asn pool

Specifies the ASN pool for rack border leaf nodes. Valid values are numbers from 4200065535 through 4200065635.

--anycast-mac-address asn pool

Specifies the IPv4 anycast MAC address.

--ipv6-anycast-mac-address mac

Specifies the IPv6 anycast MAC address.

--mac-aging-timeout timeout

Specifies the MAC aging timeout. Valid values are 0 (for no timeout) or 60 through 86400.

--mac-aging-conversation-timeout timeout

Specifies the MAC conversational aging timeout in seconds. Valid values are 0 (for no timeout) or 60 through 100000.

--mac-move-limit limit

Specifies the MAC move detect limit. Valid values range from 5 through 500.

--duplicate-mac-timer time

Specifies the number of seconds for detecting a duplicate MAC address.

--duplicate-mac-timer-max-count max

Specifies the maximum number of duplicate MAC addresses that can be detected.

--configure-overlay-gateway yes | no

Configures an overlay gateway.

--bfd-enable yes | no

Turns bidirectional forwarding detection (BFD) on or off.

--bfd-tx interval

Specifies the BFD minimum transmit interval in milliseconds. Valid values range from 50 through 30000.

--bfd-rx interval

Specifies the BFD minimum receive interval in milliseconds. Valid values range from 50 through 30000.

--bfd-multiplier multiplier

Specifies the number of times that a packet is missed before BFD declares the neighbor is down. Valid values range from 3 through 50.

--bgp-multihop ttl

Determines the TTL value for EBGP neighbors that are not on directly connected networks. Valid values range from 1 through 255.

--max-paths paths

Specifies the maximum number of paths over which packets can be forwarded. Valid values range from 1 through 64.

--allow-as-in path

Turns off the AS_PATH check of the routes learned from the AS. Valid values range from 1 through 10.

--mtu size

• For SLX-OS 21.1 and later versions: The MTU size in bytes. Valid values range from 1500 through 9216.
• For other SLX-OS versions: The MTU size in bytes. Valid values range from 1548 through 9216.

--ip-mtu size

Specifies the IPv4 or IPv6 MTU size. Valid values range from 1300 through 9194.

--leaf-peer-group group-name

Specifies the name of the leaf peer group. Valid name length is from 1 through 63 characters.

--spine-peer-group group-name

Specifies the name of the spine peer group. Valid name length is from 1 through 63 characters.

--super-spine-peer-group group-name

Specifies the name of the super spine peer group. Valid name length is from 1 through 63 characters.

--rack-underlay-ebgp-peer-group group-name

Specifies the name of the EBGP peer group of the rack underlay. Valid name length is from 1 through 63 characters.

--rack-overlay-ebgp-peer-group group-name

Specifies the name of the EBGP peer group of the rack overlay. Valid name length is from 1 through 63 characters.

--mctlink-ip-range pool

Specifies the IP address pool to be used for MCT peering.

--lacp-timeout long | short

Specifies LACP timeout for MCT member ports. Accepted values are long and short.

--mct-port-channel id

Specifies the port-channel interface ID to be used as an MCT peer-interface. Valid values range from 1 through 64.

--single-rack-deployment yes | no

Specifies whether single-rack deployment is used. The default is no.

--control-vlan id

Specifies the ID of the VLAN to be used as the MCT cluster control VLAN. Valid values range from 1 through 4090.

--control-ve id

Specifies the ID of the VE to be used as the MCT cluster control VE. Valid values range from 1 through 4090.

--vni-auto-map yes | no

Specifies whether to automatically map the VTEP VLAN (or bridge domain) to VNI mode.

--backup-routing-enable yes | no

Turns backup routing on or off.

--backup-routing-ipv4-range range

Specifies the IPv4 backup routing range.

--backup-routing-ipv6-range range

Specifies the IPv6 backup routing range.

--optimized-replication-enable Yes | No

Enables optimized replication.

--mdtgroup-range range

Specifies the IPv4 multicast address range in IP prefix format. For example: 239.0.0.0/8

--default-mdtgroup ipv4-address

Specifies the default IPv4 multicast address. The address must be from the MDT group range.

---md5-password password

Specifies the BGP MD5 password to be used on fabric links. If the password is a word, the following rules apply: 1-80 for plain text and 1-164 for encrypted string. The default is "<prompt>".

---md5-password-enable yes | no

Enables or disables the BGP MD5 password on fabric links.

---bgp-dynamic-peer-listen-limit peers

Specifies the maximum number of dynamic BGP peers that can be operational across the VRFs in the SLX. Valid values range from 1 through 2400. The default is 100.