The following issues were resolved in ExtremeXOS 22.4. ExtremeXOS 22.4 includes all fixes up to and including ExtremeXOS 11.6.5.3, and earlier, ExtremeXOS 12.0.5, ExtremeXOS 12.1.7, ExtremeXOS 12.2.2-patch1-12, ExtremeXOS 12.3.6, ExtremeXOS 12.4.5, ExtremeXOS 12.5.5, ExtremeXOS 12.6.3, ExtremeXOS 12.6.5, ExtremeXOS 12.7.1, ExtremeXOS 15.1.5, ExtremeXOS 15.2.4, ExtremeXOS 15.3.3, ExtremeXOS 15.4.1, ExtremeXOS 15.5.1, ExtremeXOS 15.5.2, ExtremeXOS 15.6.1, ExtremeXOS 15.6.2, ExtremeXOS 15.7.1, ExtremeXOS 16.1, ExtremeXOS 16.1.2, ExtremeXOS 16.1.3, ExtremeXOS 21.1, ExtremeXOS 22.1, ExtremeXOS 22.2, and ExtremeXOS 22.3. For information about those fixes, see the release notes for the specific release.
Resolved Issues, Platform-Specific, and Feature Change Requests (CRs) in 22.4
| CR Number | Description |
|---|---|
| General | |
| xos0054568 | ESVT fails to function with jumbo-sized loopback frames. The "show esvt traffic-test" output indicates the test completed successfully, but no frame counts are indicated. |
| xos0062785 | Need a mechanism to avoid configuring static route gateway and local IP as the same. |
| xos0065833 | Deleting user account causes ExtremeXOS to end unexpectedly with the message: "Process aaa pid 2251 died with signal 5". |
| xos0066935 | Files are not deleted in standby nodes after removing files in master node which was created through "save" operation. |
| xos0066960 | Setting a rate limit value, and then resetting back to default, does not return traffic back to 100% throughput. Traffic stops completely instead. |
| xos0067067 | Need the ability to change a LAG‘s algorithm after LAG creation. |
| xos0067587 | When running show tech-support command with user-created VRs, show configuration command does not display full configuration. |
| xos0067726 | BOOTPRelay currently supports up to 4 servers per VR and 4 servers per VLAN. Need to increase support to up to 8 servers. |
| xos0067745 | On ExtremeSwitching X690 and X870 series switches, "Rx Pkts Count" does not increment as shown in the command show port statistics when the L2 frame has EtherType as "none". |
| xos0068304 | External PSU status appears as "failed" in "show power" command output even though it is not present. |
| xos0068323 | In ExtremeXOS Python scripting, the argument sent to the command Exsh.clicmd is replicated 24 times. |
| xos0068810 | SNMP walk on entPhysicalClass returns Other(1) instead of Fan(7) for fan trays. |
| xos0068888 | When the command show tech-support all detail is executed after running enable cli-config-logging, messages beginning with "serial unknown" appear in the log. This issue also occurs when executed from a Telnet session. |
| xos0068902 | On ExtremeSwitching X440-G2, X620, Summit X46-0G2 series switches, and SummitStack,configure port preferred medium copper on a disabled combo port makes its peer end active. |
| xos0069058 | LACP packets are sent with VLAN tag 0 from backup node on a SummitStack. |
| xos0069070 | The process BCMAsync stops processing with scaled route/ARP entries in hash table. |
| xos0069094 | Unable to run the command unconfigure switch all on ExtremeXOS virtual machines. |
| xos0069114 | The show configuration command output displays additional word "minutes" under "aaa" module when lockout-time-period is configured. |
| xos0069150 | In the output of the show vlan command, ports can have both "!" and "*" flags set if the port is a share group port. |
| xos0069196 | Inconsistent port learning flag appears in HAL with PVLAN and MLAG configuration. |
| xos0069206 | After Enabling NTP on a VLAN, if the VLAN name is changed, the change is not reflected in show ntp. |
| xos0069210 | Unable to create private VLAN with 32-character name if the first 31 characters match an existing private VLAN name. |
| xos0069450 | Unable to filter link up/down log events based on port number. |
| xos0069580 | The command show configuration bfd shows enable bfd vlan even though it is not explicitly enabled. |
| xos0069604 | The process rtmgr ends unexpectedly with signal 11 after running "disable/enable ospf" in peer switch. |
| xos0069622 | Process devmgr signal 11 crash occurs when executing debug cfgmgr command. |
| xos0069691 | EXOS-VM displays coreDumpWrite failed error during bootup. |
| xos0069808 | Kernel crash occurs when processing a IGMP packet with an invalid IP header length. |
| xos0069823 | The output of the show fan command reports 0 RPM for other stack node‘s fans intermittently. |
| xos0066721 | The command configure vlan untagged-ports auto-move needs to have inform as the default. |
| SummitStack | |
| xos0057915 | A SummitStack booted from factory default configuration (particularly after unconfigure switch all with no default or autoexec scripts) has the backup node with ports configured. |
| xos0058419 |
After rebooting a stack, error messages similar to the following appear for ports
belonging to LAGs:
Erro:cm.sys.actionErr> Slot-2: Error while loading "ports": Speed change is not allowed on port 2:6 as it is a trunk member port. |
| xos0067001 | With IPv4 bi-directional tarffic forwarded, rebooting the backup node causes the switch to stop responding and the message "Process epm pid 1393 died with signal 6" appears. |
| xos0068388 | Unable to query objects in the extremeStackMemberTable and extremeStackingPortTable. |
| xos0068759 | On Summit X460-G2 stacks, with IPv4 Unicast traffic, the backup node remains in the "present" state after rebooting. |
| xos0069761 | Telneting to another slot does not work if the current logon user name has 6 or more greater characters. |
| ExtremeSwitching X440-G2 Series Switches | |
| xos0062256 | When auto-polarity is turned off, link comes up for straight cable rather than crossover connection. |
| xos0068490 | On ExtremeSwitching X440G2-48P/48t switches, cable diagnostic script (cablediag.py) does not work. |
| xos0068737 | PTPv2 packets are duplicated and egress at twice the incoming rate after enabling GPTP on the ingress ports. |
| ExtremeSwitching X690 Series Switches | |
| xos0067675 | EEE does not work on ExtremeSwitching X690-48t switches. |
| xos0067933 | On ExtremeSwitching X690 series switches, the following behavior occurs when
setting autonegotiation:
|
| xos0068870 | BX40-D) transceivers, show port configuration display a media type of "NONE". |
| xos0068871 | When using the OE Solutions RBT12SVX-IT4 (MGBIC-BX120-U) and RBT12SVX-IT5 (MGBIC-BX120-D) transceivers, media type appears as "NONE" when issuing the show port configuration command. |
| xos0068971 | On ExtremeSwitching X690 series switches, port 72 configured for 25G does not link up with autonegotiation turned on. |
| ExtremeSwitching X620 Series Switches | |
| xos0068344 | On ExtremeSwitching X620 series switches, fiber combo ports do not come up when the preferred medium copper link is down. |
| xos0068874 | On ExtremeSwitching X620 series switches, when using optic "SPG-DR-LX-IDFC-EX" from Source Photonics if auto-negotiation is turned "on" there is a traffic issue. |
| xos0069916 | For ExtremeSwitching X620-10x, switches, frequent link flaps occur on 1m passive copper cable when connected with an Intel NIC card. |
| Summit X670-G2 Series Switches | |
| xos0068353 | For Summit X670-G2 series switches acting as a VRRP master, SSH session is not established for some prefixes after upgrading to ExtremeXOS 22.2. |
| Summit X770 Series Switches | |
| xos0068553 | The ARP learning rate on the Summit X770 series switches has decreased starting with ExtremeXOS 22.2 due to code infrastructure changes. |
| xos0069068 | On Summit X770 and X670-G2 series switches with with IPv4 forwarding enabled and more than 32 ARPs, IPv4 unicast traffic destined to IPv4 addresses residing on port number 64 or higher may be dropped. |
| xos0069487 | HAL process ends unexpectedly with signal 6 when switch boots up with PTP configurations. |
| ExtremeSwitching X870 Series Switches | |
| xos0069072 | On ExtremeSwitching X870 series switches, traffic ingressing ISC ports get forwarded on MLAG ports if ports are between 91–96. |
| Summit X460-G2 Series Switches | |
| xos0069051 | After 65,000 new FDB entries are learned, subsequent entries are continuously added and deleted. |
| xos0069998 | |
| ACL | |
| xos0048459 | The following notification do not appear for all
platforms while refreshing the policy.
<Noti:ACL.Policy.TotChanges> Policy:smart refresh:tmp_3198. Total number of changes 1. |
| xos0069576 | Memory leak occurs in Policy process when flapping the interface. |
| BGP | |
| xos0067757 | After disabling BGP, and then executing <i>disable bgp neighbor all</i>, switch becomes unresponsive. |
| Identity Management | |
| xos0066783 | Using IDMgr, UPM, and Policy combination makes client not reachable untill IDMgr settles down. |
| MLAG | |
| xos0066886 | Continuously, restarting MLAG ports causes brief loops. |
| MPLS | |
| xos0059159 | An error message (EMS) is required when H-VPLS is down due to no pseudowire status support. |
| xos0068785 | L2PT packets fail to switch over to backup path during failover. |
| xos0069696 | Traffic is not forwarded in VPLS tunnel after disable/enable sharing on VMAN CEP ports. |
| xos0069800 | After ESRP failover L2VPN session remain in signaling state with ESRP VPLS redundancy enabled. |
| NetLogin | |
| xos0065868 | With scaled NetLogin entries in policy mode, with convergence endpoint enabled, executing any show commands causes switch to stop responding. |
| Optics | |
| xos0057140 | Transceiver information for 40G Q+SR4 optic module shows invalid power and threshold values. |
| xos0067434 | On ExtremeSwitching X440-G2 and X620 series switches, link flaps occur when inserting/removing the following optics: AFBR-709SMZ-EX1, AFCT-739SMZ-EX1, FTLX8574D3BCL-EX. |
| xos0067489 | Link flaps occur when optic is removed, and then re-inserted, and after reboots. |
| xos0069737 | The thresholds and status values shown in the command show ports transceiver information detail are not calculated properly for ExtremeSwitching X690 and X870 series switches. |
| xos0069888 | Transceiver DDMI threshold, status, and measurement values on the ExtremeSwitching X870 and X690 series switches are incorrectly calculated. |
| xos0069657 | When using 100FX with phy optic in ExtremeSwitching X620 series switches, false linkups occur after reboot. |
| OSPF | |
| xos0066618 | With OSPF enabled, the full length of long policy names do no appear in the output of show policy. |
| xos0068292 | OSPF is not establishing session after deleting the policy and rebooting. |
| Policy | |
| xos0066415 | When configuring the maximum limit of 512 for FDB entries, if 600 MAC addresses are sent all the 600 MAC addresses are getting learned though the total users authenticated is only 512 in show netlogin. Also, after disabling policy, the rules are not unconfigured properly. |
| xos0068687 | Multicast traffic sent to host randomly stops after enabling OnePolicy with PVID 4095. |
| Security | |
| xos0067280 | Uploading a file using SFTP creates a read-only file on the switch. |
| xos0069140 |
The following are ExtremeXOS vulnerabilities due to scripting allowed when in FIPS mode: Note: You must enable FIPS for this fix to take effect.
The following are additional ExtremeXOS vulnerabilities:
|
| xos0069180 | Cannot configure some IP security features after removing and adding ports from VLANs. |
| xos0069418 | Policy, Python, and script files cannot be overwritten using SFTP in WinSCP client. |
| xos0070303 | In the ExtremeXOS 22.4 User Guide, a note regarding MAC lockdown with Dot1x needs to be added. MAC lockdown feature does not work on static FDB entries. |
| SNMP | |
| xos0061552 |
The ExtremeXOS SNMP client was adapted to work with Ridgeline, which had issues dealing with partial getbulk responses, so that you could either operate in standards-compliant mode or Ridgeline-compatible mode. |
| xos0062882 | Whole MIB compilation gets stuck at EXTREME-V2-TRAP MIB. |
| xos0064666 | ExtremeXOS can only return a limited set of values to indicate success or failure of the requested set/get operation, which is returned to the SNMP client as "commitFailed(14)". |
| xos0068767 | Trap receiver configuration is not saved in ExtremeXOS when configured from Extreme Management Center. |
| xos0069715 | Dynamically assigned IP addresses do not appear when an SNMP walk is done on OID 1.3.6.1.2.1.4.20 (IPAddrTable). |
| xos0069716 | The IPAddrTable If index entry contains the Index value corresponding to the Rt-interface, and not to the corresponding VLAN interface. |
| SSH | |
| xos0069061 | Exsshd process ends unexpectedly with signal 11 during stack failover. |
| xos0069329 | Disabling the MAC cipher "3des" with command configure ssh2 disable cipher 3des appears as configure ssh2 disable cipher 3des-cbc in output of show configuration exsshd command. |
| xos0069424 | The output of the command show ssh2 private-key actually shows the private key, which could be a security threat. |
| xos0069476 | A custom user cannot SSH into the switch if agent forwarding is enabled. |
| STP | |
| xos0066518 | LLDP packets are reflected back to the sender without echo kill in PVLAN. |
| xos0067824 | STP BPDUs are continuously sent after enabling and disabling MSTP on an STP port. |
| xos0068911 | After enabling STP auto-bind on a VLAN, removing all ports from the VLAN, and then adding them back, displays STP tag as "(none)" in the show ports information detail command. |
| xos0069755 | Disabling an edge port incorrectly triggers a topology change. |
| xos0069318 | When an ingress port is part of both tagged and untagged VLANs that are participating in MSTP, the BPDU is not processed. |
| VRRP | |
| xos0067270 | VRRP flap occurs with CPU congestion. |
Print
this page
Email this topic
Feedback
View PDF
Download EPUB