efa inventory device setting update

Configures device settings such as maintenance mode.

Syntax

efa inventory device setting update [ --ip device-ips| --fabric fabric-name | --maint-mode-enable-on-reboot { Yes | No } --maint-mode-enable { Yes | No } --health-check-enable { Yes | No } --health-check-interval minutes| --health-check-heartbeat-miss-threshold { 2 | 3 | 4 | 5 } --config-backup-periodic-enable { Yes | No } --config-backup-interval interval | --number-of-config-backups count | --mct-bring-up-delay delay | --maint-mode-convergence-time time |--prefix-independent-convergence { Yes | No } | --prefix-independent-convergence-static { Yes | No } |--maximum-load-sharing-paths { 8 | 16 | 32 | 64 } | --maximum-ipv6-prefix-length-64 strimg | --urpf string |-h, --help ]

Parameters

--ip device-ips
Specifies a comma-separated range of device IP addresses. For example:

10.1.1.13,10.1.1.50,10.1.1.101.

--fabric fabric-name
Specify the name of the fabric.
--maint-mode-enable-on-reboot { Yes | No }
Specify Yes to activate maintenance mode on reboot and No to deactivate it.
--maint-mode-enable { Yes | No }
Specify Yes to activate maintenance mode and No to deactivate it.
--health-check-enable { Yes | No }
Specify Yes to enable health check and No to disable it.
--health-check-interval minutes
Specifies the health check interval in minutes. Valid values are 6m through 24h. Default is 6m.
--health-check-heartbeat-miss-threshold { 2 | 3 | 4 | 5 }
Specifies the health check miss threshold.
--config-backup-periodic-enable { Yes | No }
Specify Yes to enable periodic configuration backup and No to disable it.
--config-backup-interval interval
Specifies configuration backup interval, in minutes. Valid values are 3m through 30h. The default is 24h.
--number-of-config-backups count
Specifies configuration backup count. Valid values are 2-20. The default is 4.
--mct-bring-up-delay delay
Specifies delay, in seconds, before an MCT cluster bring up. Valid values are 10-600. Default is 90. Set a value of 0 to deconfigure.
--maint-mode-convergence-time time
Specifies the maximum time, in seconds, that maintenance mode is allowed to complete operations. Valid values are 100-500. Default is 300. Set a value of 0 to deconfigure.
--prefix-independent-convergence { Yes | No }
Specify Yes to enable BGP PIC and No to de-configure it.
--prefix-independent-convergence-static { Yes | No }
Specify Yes to enable Static PIC and No to de-configure it.
--maximum-load-sharing-paths string
Specifies the route load-sharing maximum paths. Valid values are 8,16,32,64. The default is 64 paths.
--maximum-ipv6-prefix-length-64 string
Enter Yes to configure the maximum route prefix length of 64. This configuration is applicable for Extreme 8820, 8720, 8520 hardware.
--urpf string
Enter Yes to configure the maximum route prefix length of 64 along with unicast reverse path forwarding. This configuration is applicable for Extreme 8820, 8720, 8520 hardware.
-h, --help
Help for update.

Examples

This example specifies a delay of 200 seconds before an MCT cluster bring up.
$ efa inventory device setting update –-ip 10.20.24.10 
–-mct-bring-up-delay 200
This example specifies a maximum time of 100 seconds that maintenance mode is allowed to complete operations.
$ efa inventory device setting update –-ip 10.20.24.10 
–-maint-mode-convergence-time 100 
This example enables prefix independent convergence on the device.
efa inventory device setting update –-ip 10.20.24.10 --prefix-independent-convergence
Yes					
Warning: The best practice is to clear all routes after configuring PIC. You can also reload the device.					
Execute the CLI to clear : efa inventory device clear route-all –-ip 10.20.24.1
This example enables prefix independent convergence static on the device.
efa inventory device setting update --ip 10.20.24.18 --prefix-independent-convergence-static yes
+--------------+--------------------------------+---------+-------+-------+
|  IP ADDRESS  |              NAME              | STATUS  | VALUE | ERROR |
+--------------+--------------------------------+---------+-------+-------+
| 10.20.24.18 | Static Prefix Independent      | Success | Yes   |       |
|              | Convergence Enabled            |         |       |       |
+--------------+--------------------------------+---------+-------+-------+
Warning: The best practice is to clear all routes after configuring Static PIC. You can also reload the device.
Execute the CLI to clear : efa inventory device clear route-all --ip 10.20.24.18
Execute the CLI to reload : efa inventory device reload --ip 10.20.24.18
				
This example configures the maximum route prefix length of 64.
efa inventory device setting update –-ip 10.24.80.135 --maximum-ipv6-prefix-length-64 
Warning: Configuration will not take effect until reloaded. 
Execute the CLI to reload : efa inventory device reload –-ip 10.24.80.135