efa tenant service bgp peer update

Parameters

--description description

Describes the BGP service.

--ipv4-uc-dyn-nbr string

Identifies the IPv4 unicast dynamic neighbor with a string in the following format: device-ip,vrf-name:ipv4-listen-range,peer-group-name,listen-limit. For example: 10.x.x.x,red:11::22/127. The listen-limit value is optional.

--ipv4-uc-nbr string

Identifies the IPv4 unicast neighbor. For peer-add operations, enter a string in the following format: device-ip,vrf-name:ipv4-neighbor,remote-as. For example: 10.x.x.x,red:10.20.30.40,5000. The remote-as value is not required for peer-delete operations.

--ipv4-uc-nbr-bfd string

Identifies the IPv4 BFD unicast neighbor with a string in the following format: device-ip,vrf-name:ipv4-neighbor,bfd-enable(true/false),bfd-interval,bfd-min-rx,bfd-multiplier. For example: 10.x.x.x,red:10.20.30.40,true,100,200,5. BFD parameters are optional for peer-add operations and not required for peer-delete operations.

--ipv4-uc-nbr-send-community string

Updates the send-community in the following format: device-ip,vrf-name:neighbor-ip, (all | both | extended | large | standard | large-and-standard | large-and-extended).

--ipv4-uc-nbr-remove-private-as stringArray

Turns the remove-private-as setting on or off per BGP peer group, created for external connectivity, in the following format: <device-ip,vrf-name:neighbor-ip,true|false. For example: 10.20.246.15,ten1vrf1:10.20.30.40,true.

By default, the setting is off.

--ipv4-uc-nbr-default-originate stringArray

Identifies the default-originate setting for the IPv4 unicast neighbor, with a string in the following format: device-ip,vrf-name:neighbor-ip,true/false. For example: 10.20.246.15,ten1vrf1:10.20.30.40,true.

--ipv4-uc-nbr-default-originate-route-map stringArray

Identifies the default-originate setting for the IPv4 unicast neighbor, with a string in the following format: device-ip,vrf-name:neighbor-ip,route-map. For example: 10.20.246.16,ten1vrf1:10.20.30.40,rmap1.

This parameter is optional.

--ipv4-uc-nbr-next-hop-self string

Identifies the next-hop-self for the IPv4 unicast neighbor with a string in the following format: device-ip,vrf-name:ipv4-neighbor,next-hop-self(true/false/always). For example: 10.x.x.x,red:10.y.y.y,true.

--ipv4-uc-nbr-update-source-ip string

Updates the source IP for the IPv4 unicast neighbor with a string in the following format: device-ip,vrf-name:ipv4-neighbor,update-source-ip. For example: 10.x.x.x,red:10.y.y.y,11.x.x.x.

--ipv4-uc-nbr-route-map stringArray

Identifies the IPv4 BFD route map, in the following format: device-ip,vrf-name:neighbor-ip,route-map-name. For example: 10.20.246.15,ten1vrf1:10.20.30.40,rmap1.

--ipv4-uc-nbr-md5-password password

IPv4 Unicast Neighbor md5-password in the format device-ip,vrf-name:ipv4-neighbor,ipv4-md5-password.

Example for encrypted/password containing special characters: --ipv4-uc-nbr-md5-password device-ip,vrf-name:ipv4-neighbor,'$9$MCgKGaNt6OASX68/7TC6Lw=='

--ipv4-uc-nbr-prefix-list stringArray

IPv4 Unicast Neighbor prefix list in the format device-ip,vrf-name:ipv4-neighbor,prefix-list-name,direction(in/out)

--ipv6-uc-nbr-prefix-list stringArray

IPv6 Unicast Neighbor prefix list in the format device-ip,vrf-name:ipv6-neighbor,prefix-list-name,direction(in/out)

--name peer-name

Identifies the name of the BGP peer instance.

--operation { peer-add | peer-delete | desc-update }

Identifies the type of operation you are performing: add a peer, delete a peer, or update a description.

--tenant tenant-name

Identifies the name of the tenant.

--md5-password-prompt-enable { true | false }

Turns on secure input for the MD5 password. The default is false.

--ipv6-us-nbr-send-community stringArray

Updates the send-community in the following format: device-ip,vrf-name:neighbor-ip, (all | both | extended | large | standard | large-and-standard | large-and-extended).

--ipv6-uc-dyn-nbr string

Identifies the IPv6 unicast dynamic neighbor with a string in the following format: device-ip,vrf-name:ipv6-listen-range,peer-group-name,listenlimit. The listen-limit value is optional.

--ipv6-uc-nbr string

Identifies the IPv6 unicast neighbor with a string in the following format: device-ip,vrfname:ipv6-neighbor,remote-as. For example: 10.x.x.x,red:10::40,5000.

--ipv6-uc-nbr-bfd string

Identifies the IPv6 BFD unicast neighbor with a string in the following format: device-ip,vrf-name:ipv6-neighbor,bfdenable(true/false),bfd-interval,bfd-min-rx,bfd-multiplier. For example: 10.x.x.x,red:10::40,true,100,200,5.

--ipv6-uc-nbr-default-originate stringArray

Identifies the IPv6 unicast neighbor default originate in the following format: device-ip,vrfname:ipv6-neighbor,default-originate(true/false).

--ipv6-uc-nbr-default-originate-route-map stringArray

Identifies the IPv6 unicast neighbor default originate route map in the following format: device-ip,vrf-name:ipv6-neighbor,route-map-name.

--ipv6-uc-nbr-md5-password string

Identifies the IPv6 unicast neighbor default originate route map in the following format: device-ip,vrf-name:ipv6-neighbor,route-map-name.

Parameters

--ipv6-uc-nbr-next-hop-self string

Identifies the next-hop-self for the IPv6 unicast neighbor with a string in the following format: device-ip,vrf-name:ipv6-neighbor,next-hop-self(true/ false/always). For example: 10.x.x.x,red:10::40,true.

--ipv6-uc-nbr-remove-private-as stringArray

Identifies the IPv6 unicast neighbor remove private AS in the format: device-ip,vrfname:ipv6-neighbor,remove-private-as(true/false).

--ipv6-uc-nbr-route-map stringArray

Identifies the IPv6 unicast neighbor route map in the format: device-ip,vrf-name:ipv6neighbor,route-map-name,direction(in/out).

--ipv6-uc-nbr-update-source-ip string

Updates the source IP address for the IPv6 unicast neighbor with a string in the following format: device-ip,vrf-name:ipv6-neighbor,update-source-ip. For example: 10.x.x.x,red:10::40,11::22.

--ipv4-uc-nbr-add-path-capability string

Identifies the BGP neighbor add-path capability in the format device-ip,vrf-name:ipv4-neighbor,add-path-capability. Valid values are (send / receive / both).

--ipv4-uc-nbr-add-path-advertise-all string

Identifies the BGP neighbor add-path advertise all in the format device-ip,vrf-name:ipv4-neighbor,add-path-advertise-all(true/false).

--ipv4-uc-nbr-add-path-advertise-group-best string

Identifies the BGP neighbor add-path advertise group best in the format device-ip,vrf-name:ipv4-neighbor,add-path-advertise-group-best(true/false).

--ipv4-uc-nbr-add-path-advertise-best string

Identifies the BGP neighbor add-path advertise best in the format device-ip,vrf-name:ipv4-neighbor,add-path-advertise-best. Valid values are 2-16.

--ipv6-uc-nbr-add-path-capability string

Identifies the BGP neighbor add-path capability in the format device-ip,vrf-name:ipv6-neighbor,add-path-capability. Valid values are (send / receive / both).

--ipv6-uc-nbr-add-path-advertise-all string

Identifies the BGP neighbor add-path advertise all in the format device-ip,vrf-name:ipv6-neighbor,add-path-advertise-all(true/false).

--ipv6-uc-nbr-add-path-advertise-group-best string

Identifies the BGP neighbor add-path advertise group best in the format device-ip,vrf-name:ipv6-neighbor,add-path-advertise-group-best(true/false).

--ipv6-uc-nbr-add-path-advertise-best string

Identifies the BGP neighbor add-path advertise best in the format device-ip,vrf-name:ipv6-neighbor,add-path-advertise-best. Valid values are 2-16.