efa fabric setting update

Parameters

--name<string>

The name of the fabric

--p2p-link-range<string>

IP Pool used for P2P Link Configuration

--loopback-ip-range<string>

IP Address Pool for Loopback interface, to be used for unnumbered and VTEP IP

--rack-l3-backup-ip-range<string>

IP Address Pool for L3 Back up

--loopback-port-number<string>

Loopback ID on the device to be used as donor IP interface for the link between Leaf and Spine <NUMBER: 1-255>

--vtep-loopback-port-number<string>

Loopback ID on the device to be used as VTEP IP interface <NUMBER: 1-255>

--spine-asn-block<string>

ASN Pool For Spine Nodes, or Single AS

--super-spine-asn-block<string>

Single AS

--leaf-asn-block<string>

ASN Pool For Leaf Nodes

--border-leaf-asn-block<string>

ASN Pool For Border Leaf Nodes

--rack-asn-block<string>

ASN Pool For Rack Nodes

--anycast-mac-address<string>

IPV4 ANY CAST MAC address.mac address HHHH.HHHH.HHHH

--ipv6-anycast-mac-address<string>

IPV6 ANY CAST MAC address.mac address HHHH.HHHH.HHHH

--mac-aging-timeout <string>

MAC Aging Timeout <NUMBER: 0|60-86400>

--mac-aging-conversation-timeout<string>

MAC Conversational Aging time in seconds<NUMBER: 0|60-100000>

--mac-move-limit<string>

MAC move detect limit <NUMBER: 5-500>

--duplicate-mac-timer<string>

Duplicate Mac Timer

--duplicate-mac-timer-max-count<string>

Duplicate Mac Timer Max Count

--configure-overlay-gateway<string>

ConfigureOverlayGateway Enabled Yes/No

--bfd-enable<string>

BFD enabled Yes/No

--bfd-tx <string>

BFD desired min transmit interval in milliseconds <NUMBER: 50-30000>

--bfd-rx <string>

BFD desired min receive interval in milliseconds <NUMBER: 50-30000>

--bfd-multiplier<string>

BFD detection time multiplier <NUMBER: 3-50>

--bgp-multihop<string>

Enable EBGP neighbors not on directly connected networks <Number:1-255>

--max-paths<string>

Forward packets over multiple paths <Number:1-64>

--allow-as-in<string>

Disables the AS_PATH check of the routes learned from the AS<Number:1-10>

--mtu<string>

For SLX-OS 21.1 and later versions: The MTU size in bytes is <Number:1500-9216>. For other SLX-OS versions: The MTU size in bytes is <Number:1548-9216>

--ip-mtu<string>

For SLX IPV4/IPV6 MTU size in bytes <Number:1300-9194>

--leaf-peer-group<string>

Leaf Peer Group Name <WORD: 1-63>

--spine-peer-group<string>

Spine Peer Group Name <WORD: 1-63>

--super-spine-peer-group<string>

Super Spine Peer Group Name <WORD: 1-63>

--rack-underlay-ebgp-peer-group <string>

Rack Underlay EBGP Peer Group Name <WORD: 1-63>

--rack-overlay-ebgp-peer-group <string>

Rack Overlay EBGP Peer Group Name <WORD: 1-63>

--mctlink-ip-range<string>

Address Pool to be used for MCT peering

--mct-port-channel<string>

Port-channel interface ID to be used as MCT peer-interface <NUMBER: 1-64>

--rack-l3-backup-port<string>

Rack L3 Backup port <STRING: default '0/48'>

--rack-mct-ports<string>

Rack Mct Ports <STRING: default '0/46,0/47'>

--rack-ld-l3-backup-port<string>

Rack Low Density L3 Backup port (not applicable to SLX-9250) <STRING: default '0/32'>

--rack-ld-mct-ports<string>

Rack Low Density Mct Ports <STRING: default '0/30,0/31'>

--control-vlan<string>

VLAN ID to be used as MCT cluster control VLAN <NUMBER: 1-4090>

--control-ve<string>

VE ID to be used as MCT cluster control VE <NUMBER: 1-4090>

--vni-auto-map<string>

VTEP VLAN/BD to VNI Mode Auto <STRING: Yes/No>

-h, --help<string>

Help for the update