efa tenant vrf update

Updates the tenant VRF for various operations and parameters, such as ASN and IPv6 static route.

Syntax

efa tenant vrf update [--name vrf-name | --tenant tenant-name | --operation code |--local-asn local-asn | --ipv4-static-route-bfd route | --ipv6-static-route-bfd route | --ipv4-static-route-next-hop route | --ipv6-static-route-next-hop route | --max-path unit |--redistribute {static | connected} | --rh-max-path {8 | 16 | 64} | --rh-ecmp-enable= {true | false} | --graceful-restart-enable= {true | false } | --routing-type {distributed | centralized }]

Parameters

--name vrf-name
Specifies the VRF name.
--tenant tenant-name
Specifies the tenant name
--operation code
Identifies the operation you want to perform. Valid values are:
  • local-asn-add
  • local-asn-delete
  • redistribute-add
  • redistribute-delete
  • centralized-router-add
  • centralized-router-delete
Note

Note

Idempotency is supported for the following additional valid operations:
  • max-path-add
  • max-path-delete
  • rh-max-path-add
  • rh-max-path-delete
  • rh-ecmp-update
  • graceful-restart-update
  • static-route-add
  • static-route-delete
  • static-route-bfd-add
  • static-route-bfd-delete
--local-asn locl-asn
Specifies the local ASN for the VRF.
--ipv4-static-route-bfd route
Specifies the IPv4 static route BFD in the following format: device IP, destination IPv4 address, source IPv4 address[interval, min-rx, multiplier]. For example: 10.25.25.100,1.1.1.1,2.2.2.2,123,456,3.
--ipv6-static-route-bfd route
Specifies the IPv6 static route BFD in the following format: device IP, destination IPv6 address, source IP address[interval, min-rx, multiplier]. For example: 10.25.25.100,1::1,2::2,300,300,3.
--ipv4-static-route-next-hop route
Specifies the IPv4 static route next hop in the following format: device IP, IPv4 static route network, next hop IP, and route distance separated by commas. For example: 10.25.25.100,20.0.0.0/24,16.0.0.2. Valid values for the route distance are 1 through 254.
--ipv6-static-route-next-hop route
Specifies the IPv4 static route next hop in the following format: device IP, IPv6 static route network, next hop IP, and route distance separated by commas. For example: 10.25.25.100,2001:1::/64,3001::2,3. Valid values for the route distance are 1 through 254.
--max-path unit
Specifies the number of load-sharing paths for the VRF. Valid values are 1 through 64.
--redistribute { static | connected }
Specifies the redistribute type for routes. Valid values are static or connected.
--rh-max-path { 8 | 16 | 64 }
Specifies the maximum number of resilient hashing paths allowed per tenant VRF. Valid values are 8, 16, or 64.
--rh-ecmp-enable= {true | false }
Turns on or turns off resilient hashing for a tenant VRF. Valid values are true or false.
--graceful-restart-enable= {true | false }
Turns on or turns off graceful restart for a tenant VRF. Valid values are true or false.
--routing-type {distributed | centralized }
VRF routing type. Default value is distributed.
--centralized-router
Comma-separated list of border-leaf IP addresses.

Usage Guidelines

The --max-path and --rh-max-path parameters can co-exist.

You cannot choose the specific devices on which to configure resilient hashing. Configuration applies to all SLX devices in the tenant VRF.

This example adds redistribution connected to a VRF.
(efa:extreme)extreme@node-1:~$ efa tenant vrf update 
--name blue11 --tenant tenant11 --operation redistribute-add --redistribute connected

Vrf updated successfully.

--- Time Elapsed: 879.908437ms ---
This example removes the max-path from the VRF.
(efa:extreme)extreme@node-1:~$ efa tenant vrf update 
--name blue12 --tenant tenant1 --operation rh-max-path-delete

Vrf updated successfully.

--- Time Elapsed: 879.908437ms ---