Configure Auto-sense to Create All Learned Tunnels in the Remote Area

About this task

Note

You can only use this procedure on a switch with boundary-node abilities.

Perform this procedure to create all ExtremeCloud SD-WAN learned tunnels in the IS-IS remote area.

By default, Auto-sense creates SD-WAN logical interfaces in the home area.

Procedure

In the navigation pane, expand Configuration > Fabric.
Select AutoSense.
Select the Globals tab.
In Sd-Wan Area, select remote.
Select Apply.

Globals Field Descriptions

Use the data in the following table to use the Globals tab.


Name	Description
AccessDiffservEnable	Enables or disables the differentiated service type as access for Auto-sense ports. The default is enabled.
DataIsid	Specifies the data I-SID used by the Auto-sense ports.
EapolVoiceLldpAuthEnable	Enables the EAPoL LLDP authentication for Auto-sense voice ports. The default is disabled.
FaMsgAuthEnable	Enables or disables the FA message authentication for Auto-sense ports. The default is enabled.
FaAuthenticationKey	Specifies the FA authentication key for Auto-sense ports.
IsisHelloAuthType	Specifies the authentication type for IS-IS hello packets on Auto-sense ports: None simple - simple password authentication uses a text password in the transmitted packet. The receiving router uses an authentication key (password) to verify the packet. hmac-md5 - MD5 authentication creates an encoded checksum in the transmitted packet. The receiving router uses an authentication key (password) to verify the MD5 checksum of the packet. hmac-sha256 - with SHA-256 authentication, the switch adds an hmac-sha–256 digest to each Hello packet. The switch that receives the Hello packet computes the digest of the packet and compares it with the received digest. Note: Secure Hashing Algorithm 256 bits (SHA-256) is a cipher and a cryptographic hash function of SHA2 authentication. You can use SHA-256 to authenticate IS-IS Hello messages. This authentication method uses the SHA-256 hash function and a secret key to establish a secure connection between switches that share the same key. This feature is in full compliance with RFC 5310. The default authentication type is none.
IsisHelloAuthKeyId	Specifies the IS-IS hello authentication number key id for the Auto-sense ports.
IsisHelloAuthKey	Specifies the IS-IS hello authentication number key for the Auto-sense ports. You must configure the IS-IS hello authentication key along with the IS-IS hello authentication type.
OnboardingIsid	Specifies the onboarding I-SID used by the Auto-sense ports.
Qos8021pOverrideEnable	Overrides the incoming 802.1p bits on ports that operate in Auto-sense mode. The default is enabled.
VoiceIsid	Specifies the voice I-SID used by Auto-sense ports.
VoiceCvid	Specifies the customer VLAN ID associated with the voice I-SID used by Auto-sense ports. Voice C-Vid is configured for tagged voice traffic only. You must configure the Auto-sense voice customer VLAN ID along with the Auto-sense voice I-SID.
DhcpDetection	Enables or disables the DHCP detection in Auto-sense mode. The default is enabled.
FaCameraIsid	Specifies the FA camera I-SID used by Auto-senseports.
FaProxyMgmtIsid	Specifies the FA proxy management I-SID used by Auto-sense ports.
FaProxyMgmtCvid	Specifies the FA proxy management Client-VLAN ID (c-vid) used by Auto-sense ports.
FaProxyRingMgmtIsid	Specifies the FA proxy ring management I-SID used by Auto-sense ports.
FaProxyRingMgmtCvid	Specifies the FA proxy management Client-VLAN ID (c-vid) used by Auto-sense ports.
FaProxyNoAuthIsid	Specifies the FA proxy no-auth I-SID used by Auto-sense ports.
FaVirtualSwitchIsid	Specifies the FA virtual-switch I-SID used by Auto-sense ports.
FaWapType1Isid	Specifies the FA WAP type-1 I-SID used by Auto-sense ports.
FaCameraEapolStatus	Specifies the FA EAPoL status for Camera I-SID used by Auto-sense ports.
FaEapolOVSStatus	Specifies the FA EAPoL status for OVS (Open-Virtual-Switch) I-SID used by Auto-sense ports.
FaEapolWap1Status	Specifies the FA EAPoL status for Wap-type-1 I-SID used by Auto-sense ports.
WaitInterval	Specifies the wait interval, in seconds, for Auto-sense to wait for a Link Layer Discovery Protocol (LLDP) neighbor to be detected in the Auto-sense wait state before transitioning to the Auto-sense onboarding state. This configuration is a global configuration that applies to all Auto-sense ports. The default value is 35.
MultihostMacMax	Specifies the maximum number of EAPoL and non-EAPoL authentication MAC addresses allowed on this port. The default value is 2.
MultihostEapMacMax	Specifies the maximum number of EAPoL authentication MAC addresses allowed on this port. Zero indicates that non-EAPoL authentication is disabled for this port. The default value is 2.
MultihostNonEapMacMax	Specifies the maximum number of non-EAPoL authentication MAC addresses allowed on this port. Zero indicates that non-EAPoL authentication is disabled for this port. The default value is 2.
IsisL1Metric	Manually configure a value for the Level 1 metric. A higher number represents a higher cost and the least preferred route. The default value for L1 metric is 10 for any link, despite the port speed.
IsisL1MetricAuto	Enable the Level 1 metric as automatic. By enabling Level 1 metric as auto, the network route is determined by summing the lowest value metrics, which are inversely proportional to port speed. This ensures that the fastest port speed determines the network route. The default is disabled.
FaProxyRingMgmtIsid	Specifies the FA proxy ring management I-SID used by Auto-sense ports.
FaProxyRingMgmtCvid	Specifies the FA proxy management Client-VLAN ID (c-vid) used by Auto-sense ports.
Sd-Wan Area Note: This field only displays on a switch with boundary-node abilities.	Specifies the IS-IS area, home or remote, where Auto-sense creates all ExtremeCloud SD-WAN learned tunnels. By default, Auto-sense creates SD-WAN logical interfaces in the home area. You can also configure exceptions for specific tunnels. For more information, see Configure the IS-IS Area for a Specific Tunnel.