threshold-monitor sfp
Configures monitoring of SFP parameters.
Syntax
threshold-monitor sfp
[
apply
|
pause
|
policy
]
threshold-monitor sfp
apply
policy-name
threshold-monitor sfp
pause
threshold-monitor sfp
policy
policy-name
type
{
1GCOP
|
1GCWDM
|
1GLHA
|
1GLR
|
1GSR
|
10GDWDMT
|
10GER
|
10GLR
|
10GSR
|
10GUSR
|
10GZR
|
40GER
|
40GESR
|
40GLM
|
40GLR
|
40GSR
|
40GSRINT
|
100GAOC
|
100GCLR
|
100GCWDM
|
100GESR
|
100GLR
|
100GLRLT
|
100GPSM
|
100GSR
}
area
{
Current
|
RXP
|
TXP
|
Temperature
|
Voltage
}
threshold
{
buffer
buffer-threshold-value
|
high-threshold
high-threshold-value
|
low-threshold
low-threshold-value
}
threshold-monitor sfp
policy
policy-name
type
{
1GCOP
|
1GCWDM
|
1GLHA
|
1GLR
|
1GSR
|
10GDWDMT
|
10GER
|
10GLR
|
10GSR
|
10GUSR
|
10GZR
|
40GER
|
40GESR
|
40GLM
|
40GLR
|
40GSR
|
40GSRINT
|
100GAOC
|
100GCLR
|
100GCWDM
|
100GESR
|
100GLR
|
100GLRLT
|
100GPSM
|
100GSR
}
area
{
Current
|
RXP
|
TXP
|
Temperature
|
Voltage
}
alert
{
[
above
highthreshold-action
[
all
|
email
|
none
|
raslog
]
]
|
[
below
[
highthreshold-action
|
lowthreshold-action
]
[
all
|
email
|
none
|
raslog
]
}
no threshold-monitor sfp
policy
policy-name
Parameters
-
apply
policy-name
- Applies a SFP policy created by the threshold-monitor sfp policy
threshold command. The policy-name is always
custom.
-
pause
- Pauses the enforcement of the currently applied SFP policy.
-
policy
custom
- Creates a custom SFP policy with the provided policy-name
value. This policy can then be applied using the threshold-monitor
sfp apply command. This policy-name should always be
custom. You cannot assign an arbitrary name for the SFP policy.
-
type
- Specifies the SFP type. Possible configurations are:
-
1GCOP
- SFP type 1G SFP Copper
-
1GCWDM
- SFP type 1G CWDM
-
1GLHA
- 1G SFP LHA
-
1GLR
- 1G SFP LR
-
1GSR
- 1G SFP SR
-
10GDWDMT
- 10G SFP+ DWDM Tunable
-
10GER
- 10G SFP+ ER
-
10GLR
- 10G SFP+ LR
-
10GSR
- 10G SFP+ SR
-
10GUSR
- 10G SFP+ USR
-
10GZR
- 10G SFP+ ZR
-
40GER
- 40G QSFP+ ER4
-
40GESR
- 40G QSFP+ eSR4
-
40GLM
- 40G QSFP+ LM4
-
40GLR
- 40G QSFP+ LR4
-
40GSR
- 40G QSFP+ SR4
-
40GSRINT
- 40G QSFP+ SR4 INT
-
100GAOC
- 100G QSFP28 AOC
-
100GCLR
- 100G QSFP28 CLR4
-
100GCWDM
- 100G QSFP28 CWDM4
-
100GESR
- 100G QSFP28 eSR4
-
100GLR
- 100G QSFP28 LR4
-
100GLRLT
- 100G QSFP28 LR4 Lite
-
100GPSM
- 100G QSFP28 PSM4
-
100GSR
- 100G QSFP28 SR4
-
area
[
Current
|
RXP
|
TXP
|
Temperature
|
Voltage
]
- Specifies the SFP parameter to be measured.
-
Current
- Measures the current supplied to the SFP transceiver.
-
RXP
- Measures the incoming laser power, in microWatts (µW).
-
TXP
- Measures the outgoing laser power, in microWatts (µW).
-
Temperature
- Measures the temperature of the SFP, in degrees Celsius.
-
Voltage
- Measures the voltage supplied to the SFP.
-
threshold
- Configures the threshold value for this SFP profile. Can be one or more of:
-
buffer
buffer-threshold-value
- Configures the Buffer threshold value.
-
high-threshold
high-threshold-value
- Configures the high threshold value.
-
low-threshold
low-threshold-value
- Configures the low threshold value.
-
highthreshold-action / lowthreshold-action
- Specifies the action to be taken when a threshold is exceeded. The values
supported are
all,
none, raslog, and
snmp. The default action is
all.
-
all
- RASLOG and SNMP trap will be sent when the threshold is
exceeded. This is the default configuration.
-
none
- No action will be taken when the threshold is exceeded.
-
raslog
- Only RASLOG will be sent when the threshold is exceeded.
-
snmp
- Only SNMP traps will be sent when the threshold is exceeded.
Modes
Global Configuration Mode
Usage Guidelines
The no form of this command will remove the configured custom SFP policy.
The low-threshold threshold value cannot be higher than the value
configured for the high-threshold threshold value.
Examples
The following example shows the creation and application
of a custom SFP policy.
SLX# configure terminal
SLX (config)# threshold-monitor sfp policy custom type 100GLR area Voltage
threshold high-threshold 95 low-threshold 50 buffer 75
SLX (config)# threshold-monitor sfp apply custom
The following example shows how to pause the applied SFP policy.
SLX# configure terminal
SLX (config)# threshold-monitor sfp pause
The following example removes the applied custom SFP policy.
SLX# configure terminal
SLX (config)# no threshold-monitor sfp custom
