Note
SNMP Set operations are not allowed for "Mgmt" and "Default" VLANs.| Table/Group | Supported Variables | Comments |
|---|---|---|
|
extremeVirtualGroup |
extremeNextAvailableVirtIfIndex |
|
|
extremeVlanIfTable |
extremeVlanIfIndex |
While creating a new row in the extremeVlanIfTable, the value of the object extremeVlanIfDescr must be specified. For all tables in this MIB that contain objects with RowStatus semantics, the only values supported are: {active, createAndGo, destroy}. |
|
extremeVlanIfDescr |
This is a description of the VLAN interface. |
|
|
extremeVlanIfType |
The VLAN interface type. |
|
|
extremeVlanIfGlobalIdentifier |
Not supported. |
|
|
extremeVlanIfStatus |
The status column for this VLAN interface. This object can be set to: active (1); createAndGo (4); createAndWait (5); destroy (6). The following values may be read: active (1); notInService (2); notReady (3). |
|
|
extremeVlanIfIgnoreStpFlag |
Not supported. |
|
|
extremeVlanIfIgnoreBpduFlag |
Not supported. |
|
|
extremeVlanIfLoopbackModeFlag |
Setting this object to true causes loopback mode to be enabled on this VLAN. |
|
|
extremeVlanIfVlanId |
The VLAN ID of this VLAN. |
|
|
extremeGlobalMappingTable |
Not supported |
|
|
extremeVlanEncapsTable |
Not supported |
|
|
extremeVlanIpTable |
All objects |
For all tables in this MIB that contain objects with RowStatus semantics, the only values supported are: {active, createAndGo, and destroy}. |
|
extremeVlanProtocolTable |
Not supported |
|
|
extremeVlanProtocolBindingTable |
Partial |
For all tables in this MIB that contain objects with RowStatus semantics, the only values supported are: {active, createAndGo, and destroy}. New to the ExtremeXOS software: association of a protocol filter and VLAN. |
|
extremeVlanProtocolVlanTable |
Not supported |
|
|
extremeVlanProtocolDefTable |
Partial |
For all tables in this MIB that contain objects with RowStatus semantics, the only values supported are: { active, createAndGo, and destroy} New to the ExtremeXOS software: This is a new table introduced to add a protocol filter with etype values during creation of the filter itself. |
|
extremeVlanOpaqueTable |
All objects |
This is a read only table. For adding ports to a VLAN or deleting ports from a VLAN, use extremeVlanOpaqueControlTable. |
|
extremeVlanOpaqueControlTable |
All objects |
For all tables in this MIB that contain objects with RowStatus semantics, the only values supported are: {active, createAndGo, and destroy}. New to the ExtremeXOS software: extremeVlanOpaqueControlTable is a write only table and cannot be used to read. This is used to add/delete ports on a VLAN. |
|
extremeVlanStackTable |
All objects |
Not supported. |
|
extremeVlanL2StatsTable |
All objects |
Not supported. This table contains per VLAN information about the number of packets sent to the CPU, the number of packets learned, the number of IGMP control packets snooped and the number of IGMP data packets switched. This is the same information that is available using the CLI command show l2stats. |
|
extremePortVlanStatsTable |
VLAN statistics per port. |
|
|
extremePortVlanStatsEntry |
extremeStatsPortIfIndex |
The index of this table. |
|
extremeStatsVlanNameIndex |
The index of this table. |
|
|
extremePortVlanStatsCntrType |
Read-only. |
|
|
extremePortVlanTotalReceived BytesCounter |
The total number of bytes received by a port for a particular VLAN. |
|
|
extremePortVlanTotalReceived FramesCounter |
The total number of frames received by a port for a particular VLAN. |
|
|
extremePortVlanTotalTransmittedBytesCounter |
The total number of bytes transmitted by a port for a particular VLAN. |
|
|
extremePortVlanTotalTransmittedFramesCounter |
The total number of frames transmitted by a port for a particular VLAN. |
|
|
extremePortConfigureVlanStatus |
The row status variable, used according to row installation and removal conventions. |