ipv6 vrrp (for a port)

Syntax

• default ipv6 vrrp <1-255>

• default ipv6 vrrp <1-255> accept-mode enable

• default ipv6 vrrp <1-255> action

• default ipv6 vrrp <1-255> adver-int

• default ipv6 vrrp <1-255> backup-master enable

• default ipv6 vrrp <1-255> critical-ipv6 enable

• default ipv6 vrrp <1-255> critical-ipv6-addr

• default ipv6 vrrp <1-255> enable

• default ipv6 vrrp <1-255> fast-adv enable

• default ipv6 vrrp <1-255> fast-adv-int

• default ipv6 vrrp <1-255> holddown-timer

• default ipv6 vrrp <1-255> preempt-mode

• default ipv6 vrrp <1-255> priority

• ipv6 vrrp <1-255> accept-mode enable

• ipv6 vrrp <1-255> action none

• ipv6 vrrp <1-255> action preempt

• ipv6 vrrp <1-255> adver-int <1..40>

• ipv6 vrrp <1-255> backup-master enable

• ipv6 vrrp <1-255> critical-ipv6 enable

• ipv6 vrrp <1-255> critical-ipv6-addr WORD<0-46>

• ipv6 vrrp <1-255> enable

• ipv6 vrrp <1-255> fast-adv enable

• ipv6 vrrp <1-255> fast-adv-int <200-1000>

• ipv6 vrrp <1-255> holddown-timer <0-21600>

• ipv6 vrrp <1-255> preempt-mode enable

• ipv6 vrrp <1-255> priority <1-255>

• no ipv6 vrrp <1-255>

• no ipv6 vrrp <1-255> accept-mode enable

• no ipv6 vrrp <1-255> backup-master enable

• no ipv6 vrrp <1-255> critical-ipv6 enable

• no ipv6 vrrp <1-255> enable

• no ipv6 vrrp <1-255> fast-adv enable

• no ipv6 vrrp <1-255> preempt-mode enable

Command Parameters

<1-255>

Specifies a number that uniquely identifies a virtual router on an interface. The virtual router acts as the default router for one or more assigned addresses.

<1-255> preempt-mode enable

Enable IPv6 vrrp preempt mode.

accept-mode enable

Controls whether a master router accepts packets addressed to the IPv6 address of the address owner as its own if it is not the IPv6 address owner. The default accept-mode enable is disabled.

action <none|preempt>

Lists options to override the holddown timer manually and force preemption. None does not override the timer. preempt preempts the timer. This parameter applies only if the holddown timer is active.

adver-int <1-40>

Specifies the time interval, in seconds, between sending advertisement messages. Only the master router sends advertisements. The default is 1.

backup-master enable

Uses the backup Virtual Router Redundancy Protocol (VRRP) switch for traffic forwarding. This option reduces the traffic on the IST link. The default backupmaster enable is disabled.

critical-ip enable

Enables or disables the use of critical IP. When disabled, the Virtual Router Redundancy Protocol (VRRP) ignores the availability of the address configured as critical IP. This address must be a local address.

critical-ip-addr WORD<0-46>

Specifies an IP interface on the local router configured so that a change in its state causes a role switch in the virtual router (for example, from master to backup) in case the interface stops responding. The default critical-ip enable is disabled.

enable

Enables IPv6 Virtual Router Redundancy Protocol (VRRP). The default is disabled.

fast-adv enable

Enables or disables the fast advertisement interval. When disabled, the regular advertisement interval is used. The default fast-adv-int is 200.

fast-adv-int <200-1000>

Configures the interval between Virtual Router Redundancy Protocol (VRRP) advertisement messages. You must configure the same value on all participating routers. This unit of measure must be in multiples of 200 milliseconds.

holddown-timer<0-21600>

Configures the amount of time, in seconds, to wait before preempting the current Virtual Router Redundancy Protocol (VRRP) master. The default holddown timer is 0.

priority <1-255>

Specifies the priority value used by this Virtual Router Redundancy Protocol (VRRP) router. The value 255 is reserved for the router that owns the IP addresses associated with the virtual router. The default priority is 100.

Default

None

Command Mode

GigabitEthernet Interface Configuration