efa fabric settings update

Parameters

--mtu

The MTU size in bytes <Number:1548-9216>. The default value is 9216.

--ip-mtu

IPV4/IPV6 MTU size in bytes <Number:1300-9194>. The default value is 9100.

--bfd-enable

BFD enabled Yes/No. The default value is NO.

--bfd-tx

BFD desired min transmit interval in milliseconds <NUMBER: 50-30000>. The default value is 300.

--bfd-rx

BFD desired min receive interval in milliseconds <NUMBER: 50-30000>. The default value is 300.

--bfd-multiplier

BFD detection time multiplier <NUMBER: 3-50>. The default value is 3.

--bgp-multihop

Allow EBGP neighbors not on directly connected networks <Number:1-255>. The default value is 2.

--max-paths

Forward packets over multiple paths<Number:1-64>. The default value is 8.

--allow-as-in

Disables the AS_PATH check of the routes learned from the AS<Number:1-10>. The default value is 1.

--p2p-link-range

IP Address Pool to be used for Leaf to Spine links. The default value is 10.10.10.0/23.

--loopback-ip-range

IP Address Pool for Loopback interface, to be used for unnumbered and VTEP IP. The default value is 172.31.254.0/24.

--rack-l3-backup-ip-range

IP Address Pool for L3 Back up. The default value is 10.30.30.0/24.

--loopback-port-number

Loopback ID on the device to be used as donor IP interface for the link between Leaf and Spine. The default value is 1.

--vtep-loopback-port-number

Loopback ID on the device to be used as VTEP IP interface. The default value is 2.

--leaf-asn-block

ASN pool for Leaf nodes. The default value is 65000-65534.

--spine-asn-block

ASN pool for Spine nodes. The default value is 64512-64768.

super-spine-asn-block

ASN pool for Super-spine nodes. The default value is 64769.

--rack-asn-block

ASN Pool For Rack Nodes. The default value is 4200000000-4200065534.

--leaf-peer-group

Leaf Peer Group Name <WORD: 1-63>. The default value is leaf-group.

--spine-peer-group

Spine Peer Group Name <WORD: 1-63>. The default value is spine-group.

--super-spine-peer-group

Super-spine Peer Group Name <WORD: 1-63. The default value is spine-group.

--rack-underlay-ebgp-peer-group

Rack Underlay EBGP Peer Group Name <WORD: 1-63>. The default value is underlay-ebgp-group.

--rack-overlay-ebgp-peer-group

Rack Overlay EBGP Peer Group Name <WORD: 1-63>. The default value is overlay-ebgp-group.

--anycast-mac-address

IPV4 ANY CAST MAC address.mac address HHHH.HHHH.HHHH. The default value is 0201.0101.0101.

--ipv6-anycast-mac-address

IPV6 ANY CAST MAC address.mac address HHHH.HHHH.HHHH. The default value is 0201.0101.0102.

--mac-aging-timeout

MAC Aging Timeout <NUMBER: 0|60-100000>. The default value is 1800.

--mac-aging-conversation-timeout

MAC Conversational Aging time in seconds<NUMBER: 0|60-100000>. The default value is 300.

--mac-move-limit

MAC move detect limit <NUMBER: 5-500>. The default value is 20.

--duplicate-mac-timer

Duplicate Mac Timer. The default value is 5.

--duplicate-mac-timer-max-count

Duplicate Mac Timer Max Count. The default value is 3.

--mctlink-ip-range

IP Address Pool to be used for MCT peering. The default value is 10.20.20.0/24.

--mct-port-channel

Portchannel interface ID <NUMBER: 1-64> to be used as MCT peer-interface. The default value is 64.

--rack-l3-backup-port

Rack L3 Backup port <STRING: default '0/48'>to be used as rack 13 backup port. The default value is 48.

--rack-mct-ports

Rack MCT Port <STRING: default '0/46,0/47'>to be used as rack MCT port.

--rack-ld-l3-backup-port

Rack Low Density L3 Backup port (not applicable to SLX-9250) <STRING: default '0/32'>to be used as rack low density L3 backup port.

--rack-ld-mct-ports

Rack Low Density MCT Ports <STRING: default '0/30,0/31'>to be used as rack low density MCT port.

Rack L3 Backup port <STRING: default '0/48'>to be used as rack 13 backup port. The default value is 48.

--control-vlan VLAN ID <NUMBER: 1-4090>

VLAN ID to be used as MCT cluster control VLAN. The default value is 4090.

--control-ve VE ID <NUMBER: 1-4090>

VE ID to be used as MCT cluster control VE. The default value is 4090.

--configure-overlay-gateway

ConfigureOverlayGateway Enabled Yes/No. The default value is Yes.

--vni-auto-map

VTEP VLAN/BD to VNI Mode Auto (Yes/No). The default value is Yes.