The AP4020FX comes with the AH-ACC-BKT-AX-TB mounting bracket that can be used to mount the access point on flat t-bar ceiling grids and flat surfaces, such as Prelude ceilings (15/16 in. ceiling grid), Suprafine ceilings (flat bottomed 9/16 in. ceiling grids), and walls. The ceiling tile sides must be flat.
The AP4020FX supports up to six RP-SMA antennas, which you can attach to the AP.
| Part Number | Description |
|---|---|
| AI-TS06360 | 3.5dBi (2.4 GHz) and 5.5dBi (5 and 6 GHz) Indoor Dipole Tri-band with RP-SMA connector |
| AI-TH08055 | 6dBi Indoor Hex Sector 2.4GHz 65 Degrees and 5GHz 55 Degrees Tri-band with 6 port RP-SMA |
| AI-TH14035 | 13dBi (2.4 GHz) and 14dBi (5 and 6 GHz) Indoor Hex Sector 35 Degree Tri-band with 6 port RP-SMA |
| AI-TH06120 | 6dBi Indoor Hex Sector 120 Degree Tri-band with 6 port RP-SMA |
| Part Number | Description | Notes |
|---|---|---|
| AH-ACC-BKT-AX-TB |
Mounting bracket that can be used to mount the access point on flat surfaces such as Prelude ceilings (15/16 in. ceiling grid), Suprafine ceilings (flat bottomed 9/16 in. ceiling grid), and walls. Note: AH-ACC-BKT-AX-TB is included with the access point.
| Can be used for wall - 0.25" |
|
AH-ACC-BKT-AX-IL |
Mounting bracket for Interlude ceilings (9/16 in. wide T-bar with center protrusion). | - |
|
AH-ACC-BKT-AX-SL |
Mounting bracket for Silhouette ceilings (ceiling grid with 1/8 in. or 1/4 in. bottom opening). | Up to 0.33" ceiling tile protrusion |
|
AH-ACC-BKT-AX-WL |
Mounting bracket for direct-to-wall installations when a 1.25 in. of space is desired between the wall and the access point. | Can be used for wall - 1.25" |
| ACC-BKT-TB-NF | Mounting bracket for 15/16 in. wide T-bars with sculpted ceiling tiles. | 5/16" wide t-bars non-flat/protruded ceiling tiles |
| AH-ACC-BKT-916-KIT | Mounting bracket for 9/16 in. wide T-bars with sculpted ceiling tiles. | 9/16" non-flat/protruded ceiling tiles |
| ACC-BKT-AX-BEAM |
Mounting bracket for beam mounting. | Up to 0.78" thick beam |
|
ACC-BKT-AX-JB |
Mounting bracket for junction box or wall mounting. | Gang/junction box |
| ACC-BKT-AX-WNGADAPT | Adapter bracket for Cloud AP to WiNG Mounting Plate (#37201). Ships in a pack of 10. | Allow twist mount to mount to legacy mounts |
| ACC-BTK-AX-TBW | Mounting bracket for 1.5 in. wide extruded T-Bars with flat ceiling tiles. | - |
You can power the access point through the ETH0 RJ45 Ethernet port. But if you need to power the AP with an external power supply, you can purchase a 12V DC power supply.
| Part Number | Description |
|---|---|
| 37219 | PWR 12V DC, 3A, 2.5mm x 5.5mm connector |
The following table shows the additional accessories available for your access point.
For more information, see the Wi-Fi6 11ax Accessories Installation Guide.
| Part Number | Description |
|---|---|
|
ACC-WIFI-MICRO-USB |
Extreme Networks micro USB cable. Note: The console port can only be used with the Extreme Networks console cable. You could damage the AP if you use another cable.
Note: When you connect to the device using the micro USB Console port, the management station from which you connect to the device must have a VT100 emulation program, such as TeraTerm Pro (a free terminal emulator) or Hilgraeve HyperTerminal. Set your baud rate to 115200.
|