efa fabric setting
Displays or updates the IP fabric
settings.
Syntax
efa fabric setting show
[
--name
|
--advanced
|
--help]
efa fabric setting
update
[--name
|
--p2p-link-range
|
--loopback-ip-range
|
--rack-l3-backup-ip-range
|
--loopback-port-number
|
--vtep-loopback-port-number
|
--spine-asn-block
|
--super-spine-asn-block
|
--leaf-asn-block
|
--border-leaf-asn-block
|
--rack-asn-block
|
--anycast-mac-address
|
--ipv6-anycast-mac-address
|
--mac-aging-timeout
|
--mac-aging-conversation-timeout
|
--mac-move-limit
|
--duplicate-mac-timer
|
--duplicate-mac-timer-max-count
|
--configure-overlay-gateway
|
--bfd-enable
|
--bfd-tx
|
--bfd-rx
|
--bfd-multiplier
|
--bgp-multihop
|
--max-paths
|
--allow-as-in
|
--mtu
|
--ip-mtu
|
--leaf-peer-group
|
--optimized-replication-enable
< yes | no>|
--spine-peer-group
|
--super-spine-peer-group
|
--rack-underlay-ebgp-peer-group
|
--rack-overlay-ebgp-peer-group
|
--mctlink-ip-range
|
--lacp-timeout
|
--mct-port-channel
|
--rack-l3-backup-port
|
--rack-mct-ports
|
--rack-ld-l3-backup-port
|
--rack-ld-mct-ports
|
--control-vlan
|
--control-ve
|
--vni-auto-map
|
--backup-routing-enable
|
--backup-routing-ipv4-range
|
--backup-routing-ipv6-range
|
--mdtgroup-range
|
--default-mdtgroup
|
--help
]
Parameters
- --name
- Specifies the name of the fabric.
- --p2p-link-range
- Specifies the IP pool used for P2P Link
Configuration.
- --loopback-ip-range
- Specifies the IP Address Pool for Loopback
interface to be used for unnumbered and VTEP IP.
- --rack-l3-backup-ip-range
- Specifies the IP Address Pool for L3 Back
up.
- --loopback-port-number
- Specifies the loopback ID on the device to
be used as donor IP interface for the link between Leaf and Spine
<NUMBER: 1-255>
- --vtep-loopback-port-number
- Specifies the loopback ID on the device to
be used as VTEP IP interface <NUMBER: 1-255>
- --spine-asn-block
- Specifies the ASN Pool for spine nodes or
single AS.
- --super-spine-asn-block
- Specifies the single AS.
- --leaf-asn-block
- Specifies the ASN pool for leaf nodes.
- --border-leaf-asn-block
- Specifies the ASN pool for border leaf
nodes.
- --rack-asn-block
- Specifies the ASN pool for rack nodes.
- --anycast-mac-address
- Specifies the IPV4 ANY CAST MAC address. mac
address HHHH.HHHH.HHHH
- --ipv6-anycast-mac-address
- Specifies the IPV6 ANY CAST MAC address. mac
address HHHH.HHHH.HHHH
- --mac-aging-timeout
- Specifies the MAC Aging Timeout <NUMBER:
0|60-86400>
- --mac-aging-conversation-timeout
- Specifies the MAC Conversational Aging time
in seconds <NUMBER: 0|60-100000>.
- --mac-move-limit
- Specifies the MAC move detect limit
<NUMBER: 5-500>.
- --duplicate-mac-timer
- Specifies the duplicate MAC timer.
- --duplicate-mac-timer-max-count
- Specifies the duplicate MAC timer max
count.
- --configure-overlay-gateway
- Configures Overlay Gateway.
- --bfd-enable
- Enables or disables BFD.
- --bfd-tx
- Specifies the BFD desired min transmit
interval in milliseconds <NUMBER: 50-30000>.
- --bfd-rx
- Specifies the BFD desired min receive
interval in milliseconds <NUMBER: 50-30000>.
- --bfd-multiplier
- Specifies the BFD detection time multiplier
<NUMBER: 3-50>.
- --bgp-multihop
- Enables EBGP neighbors not on directly
connected networks <Number:1-255>.
- --max-paths
- Forwards packets over multiple paths
<Number:1-64>.
- --allow-as-in
- Disables the AS_PATH check of the routes
learned from the AS<Number:1-10>.
- --mtu
- For SLX-OS 21.1 and later versions: The MTU
size in bytes is <Number:1500-9216>. For other SLX-OS versions: The
MTU size in bytes is <Number:1548-9216>.
- --ip-mtu
- For SLX IPV4/IPV6 MTU size in bytes
<Number:1300-9194>.
- --leaf-peer-group
- Specifies the leaf peer group name <WORD:
1-63>.
- --optimized-replication-enable
- Enables optimized replication. Valid values are yes and no. Default value is
no.
- --spine-peer-group
- Specifies the Spine Peer Group Name
<WORD: 1-63>.
- --super-spine-peer-group
- Specifies the Super Spine Peer Group Name
<WORD: 1-63>.
- --rack-underlay-ebgp-peer-group
- Specifies the Rack Underlay EBGP Peer Group
Name <WORD: 1-63>.
- --rack-overlay-ebgp-peer-group
- Specifies the Rack Overlay EBGP Peer Group
Name <WORD: 1-63>.
- --mctlink-ip-range
- Specifies the address pool to be used for
MCT peering.
- --lacp-timeout
- Specifies LACP Timeout for MCT member ports.
Accepted values are long and short.
- --mct-port-channel
- Specifies the port-channel interface ID to
be used as MCT peer-interface <NUMBER: 1-64>.
- --rack-l3-backup-port
- Specifies the rack L3 backup port <:
default '0/48'>.
- --rack-mct-ports
- Specifies the rack MCT ports <STRING:
default '0/46,0/47'>.
- --rack-ld-l3-backup-port
- Specifies the Rack Low Density L3 Backup
port (not applicable to SLX-9250) <STRING: default '0/32'>.
- --rack-ld-mct-ports
- Specifies the Rack Low Density MCT Ports
<STRING: default '0/30,0/31'>.
- --control-vlan
- Specifies the VLAN ID to be used as MCT
cluster control VLAN <NUMBER: 1-4090>.
- --control-ve
- Specifies the VE ID to be used as MCT
cluster control VE <NUMBER: 1-4090>.
- --vni-auto-map
- Specifies the VTEP VLAN/BD to
VNI Mode Auto <NUMBER: Yes/No>.
- --backup-routing-enable
- Enables or disables backup routing
<STRING Yes/No>.
- --backup-routing-ipv4-range
- Specifies the IPv4 Backup Routing
Range.
- --backup-routing-ipv6-range
- Specifies the IPv6 Backup Routing
Range.
- --mdtgroup-range
- Specifies the IPv4 multicast address range in IP prefix format. Example:
239.0.0.0/8
- --default-mdtgroup
- Specifies the default IPv4 multicast address. The address must be from the
MDT group range.
- --help
- Provides help for the selected command.
# efa fabric setting –-update –-optimized-replication-enable yes –-name <fabric name>
# efa fabric setting –-update –-mdtgroup-range 239.0.0.0/8 –-name clos_fabric
# efa fabric setting –-update –-default-mdtgroup 239.1.1.1 –-name clos_fabric
