| Table/Group | Supported Variables | Comments |
|---|---|---|
| etsysConvEndPointGlobalConfigEnable |
When set to enabled(1) this object activates the current Convergence End Point configuration. When set to disabled(2) this MIB SHALL be configurable, but MUST NOT be applied, all entries will be removed from the etsysConvEndPointConnMacTable and the etsysConvEndPointConnPortTable, and any policies that have been changed as a result of End Point detection will revert to their default states. Maintaining the value of this object across agent reboots is REQUIRED. Read-write. |
|
| etsysConvEndPointGlobalConfigTable | This table represents all Convergence End Point types supported by this entity,
and provides a default policy profile for each Convergence End Point type. Not-accessible. |
|
| etsysConvEndPointGlobalConfigEntry | Defines the default policy to be applied when this type of Convergence End Point
is detected or discovered. Not-accessible. |
|
| etsysConvEndPointGlobalDefaultPolicyIndex | The policy that should be applied for this type of Convergence End Point. This
value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If
no such policy index exists, then no policy will be applied when this type of
Convergence End Point is detected or discovered. The value zero is not a valid
etsysPolicyProfileIndex, so zero indicates that no policy should be applied.
Maintaining the value of this object across system reboots is REQUIRED. Read-write. |
|
| etsysConvEndPointProtocolConfigTable | This table provides control of Convergence End Point detection and discovery on a
per interface and per Convergence End Point type basis. Maintaining the values of this
table across system reboots is REQUIRED. Not-accessbile. |
|
| etsysConvEndPointProtocolConfigEntry | The current Convergence End Point detection and discovery status for an
interface. Not-accessible. |
|
| etsysConvEndPointProtocolEndPointType | The Convergence End Point type. Not-accessible. |
|
| etsysConvEndPointProtocolEnable | When set to enabled(1), Convergence End Point detection and discovery will be
enabled on this interface for the Convergence End Point type specified. When set to
disabled(2), the Convergence End Points that have been discovered or detected on this
interface of the type specified will be removed from the etsysConvEndPointConnMacTable
and the etsysConvEndPointConnPortTable. After all of the End Points have been removed
from an interface the policy on that interface will revert to its default state. Read-write. |
|
| etsysConvEndPointGlobalConfigAccountEnable | When enabled(1), RADIUS
accounting start, interim and stop frames are sent to the configured RADIUS server(s).
When disabled(2), accounting packets are not sent to the RADIUS server. Read-write. |
|
| etsysConvEndPointConnMacTable | This table provides information on each of the Convergence End Points that has
been discovered or detected by this entity. Maintaining the value of this object
across system reboots is NOT REQUIRED. Not-accessible. |
|
| etsysConvEndPointConnMacEntry | Information about an individual Convergence End Point. Not-accessible. |
|
| etsysConvEndPointConnMacMacAddress | The MAC address of this Convergence End Point. Not-accessible. |
|
| etsysConvEndPointConnMacPortNumber | The interface on which this Convergence End Point was detected or discovered. Read-only. |
|
| etsysConvEndPointConnMacEndPointType | The type of Convergence End Point described by this row. Read-only. |
|
| etsysConvEndPointConnMacPolicyIndex | The policy applied for this Convergence End Point. This value is an
etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired
policy does not currently exist, or never did exist, then a zero MUST be returned. Read-only. |
|
| etsysConvEndPointConnMacDiscoveryTime | The time and date that this Convergence End Point was detected or discovered. Read-only. |
|
| etsysConvEndPointConnMacFirmwareVersion | This is the firmware version of the discovered Convergence End Point. If this
information is not available via the detection protocol then a zero length string MUST
be returned. Read-only. |
|
| etsysConvEndPointConnMacInetAddressType | The address type of the discovered or detected Convergence End Point. If the
address is unknown, then this object MUST return 'unknown' Read-only. |
|
| etsysConvEndPointConnMacInetAddress | The address of the discovered or detected Convergence End Point. If the address
is unknown, then this object MUST return a zero length string. Read-only. |
|
| etsysConvEndPointConnPortTable | This table provides a mapping from the entities interfaces to discovered
Convergence End Points. Maintaining the value of this object across system reboots is
NOT REQUIRED. Not-accessible. |
|
| etsysConvEndPointConnPortEntry | Information about an individual Convergence End Point. Not-accessible. |
|
| etsysConvEndPointConnPortMacAddress | The MAC address of the discovered or detected Convergence End Point. Read-only. |
|
| etsysCEPConnMacTable | This table provides information on each of the Convergence End Points that has
been discovered or detected by this entity. Maintaining the value of this object
across system reboots is NOT REQUIRED. Not-accessible. |
|
| etsysCEPConnMacEntry | Information about an individual Convergence End Point (CEP). Not-accessible. |
|
| etsysCEPConnMacEndPointType | The type of Convergence End Point described by this row. Read-only. |
|
| etsysCEPConnMacPolicyIndex | The type of Convergence End Point described by this row. Read-only. |
|
| etsysCEPConnMacPolicyIndex | The policy applied for this Convergence End Point. This value is an
etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired
policy does not currently exist, or never did exist, then a zero MUST be
returned. Read-only. |
|
| etsysCEPConnMacDiscoveryTime | The time and date that this Convergence End Point was detected or discovered.
Read-only. |
|
| etsysCEPConnMacFirmwareVersion | This is the firmware version of the discovered Convergence End Point. If this
information is not available via the detection protocol then a zero length string MUST
be returned. Read-only. |
|
| etsysCEPConnMacInetAddressType | The address type of the discovered or detected Convergence End Point. If the
address is unknown, then this object MUST return 'unknown'. Read-only. |
|
| etsysCEPConnMacInetAddress | The address of the discovered or detected Convergence End Point. If the address
is unknown, then this object MUST return a zero length string.
Read-only. |
|
| etsysConvEndPointDetectionMaxEntries | This value represents the maximum number of entries allowed in the
etsysConvEndPointDetectionTable. Read-only. |
|
| etsysConvEndPointDetectionTable | A table that describes the IP address and IP port based Convergence End Point
detection parameters. Packets on interfaces that are configured to detect End Points,
via the etsysConvEndPointProtocolConfigTable, that are defined in this table are
inspected to determine if a Convergence End Point exists on that interface. Rules
applying to Convergence End Point types that are configured for detection are
evaluated according to the following:
If there are no rows in this table that are in the active state then the following pseudo entries describe the behavior of the IP based Convergence End Point detection. EndPointType siemens Protocol { { udp, tcp } } PortLow 4060 PortHigh 4060 AddrType unknown Addr ' ' AddrMaskType unknown AddrMask '' EndPointType h323 Protocol { { udp, tcp } } PortLow 1718 PortHigh 1720 AddrType ipv4 Addr '224.0.1.41' AddrMaskType ipv4 AddrMask '255.255.255.255' EndPointType sip Protocol { { udp, tcp } } PortLow 5060 PortHigh 5060 AddrType ipv4 Addr '224.0.1.75' AddrMaskType ipv4 AddrMask '255.255.255.255' EndPointType h323 Protocol { { udp, tcp } } PortLow 1718 PortHigh 1720 AddrType unknown Addr '' AddrMaskType unknown AddrMask '' EndPointType sip Protocol { { udp, tcp } } PortLow 5060 PortHigh 5060 AddrType unknown Addr '' AddrMaskType unknown AddrMask '' If one or more entries in this table are active the active entries will define the IP based detection behavior in its entirety. Maintaining entries in this table across system reboots is REQUIRED for entries with an etsysConvEndPointDetectionRowStatus value of active(1).Not-accessible. |
|
| etsysConvEndPointDetectionEntry | Each entry represents a describes parameters for detecting a Convergence End
Point. Not-accessible. |
|
| etsysConvEndPointDetectionRuleIndex | The Convergence End Point device type that a 'hit' on this rule will indicate the
presence of. Read-create. |
|
| etsysConvEndPointDetectionProtocol | The IP protocol type that the following port range applies to. If no bits are set
then the destination port will not be evaluated as part of the detection process.
Read-create. |
|
| etsysConvEndPointDetectionPortLow | The low end of the range of the IP destination port that will be used for
Convergence End Point detection. This value represents the low value in a range of
port numbers that will be used to indicate this type of Convergence End Point. This
value must be less than or equal to etsysConvEndPointDetectionPortHigh.
Read-create. |
|
| etsysConvEndPointDetectionPortHigh | The high end of the range of the IP destination port that will be used for
Convergence End Point detection. This value represents the high value in a range of
port numbers that will be used to indicate this type of Convergence End Point. This
value must be greater than or equal to etsysConvEndPointDetectionPortLow.
Read-create. |
|
| etsysConvEndPointDetectionAddrType | The destination address type that will be used for Convergence End Point
detection. If the address type is 'unknown', then this value will not be evaluated as
part of the detection process. Read-create. |
|
| etsysConvEndPointDetectionAddr | The destination IP address that will be used for Convergence End Point detection.
If this address is null, then this value will not be evaluated as part of the
detection process. Read-create. |
|
| etsysConvEndPointDetectionAddrMaskType | The address type of the mask that will be applied to the destination IP address
as part of the Convergence End Point detection process. If the address type is
'unknown', then this value will not be evaluated as part of the detection process.
Read-create. |
|
| etsysConvEndPointDetectionAddrMask | The destination address mask that will be used for Convergence End Point
detection. If the mask is null, then this value will not be evaluated as part of the
detection process. Read-create. |
|
| etsysConvEndPointDetectionRowStatus | The status of this row as defined by the RowStatus textual convention. Rows in
this table can only transition to 'notInService', or to 'active' if the
etsysConvEndPointDetectionAddrType object and the
etsysConvEndPointDetectionAddrMaskType object have the same value, and either their
values are not 'unknown' or there is at least one bit set in the
etsysConvEndPointDetectionProtocol object. Read-create. |
|
| etsysCEPDetectionPortConfigTable | A table of per port configuration for Convergence End Point detection.
Maintaining the value of this object across system reboots is NOT REQUIRED.
Not-accessible. |
|
| etsysCEPDetectionPortConfigEntry | An entry containing per port Convergence End Point data. Only interfaces that are
able to detect Convergence End Points are represented in this table.
Not-accessible. |
|
| etsysCEPPortClearUsers | Setting this object to a value of true(1) will cause all detected or discovered
Convergence End Points to be removed from the following status tables:
etsysConvEndPointConnMacTable etsysConvEndPointConnPortTable etsysCEPConnMacTable Setting this object to a value of false(2) has no effect. This object will always return a value of false(2).Read-write. |
|
| etsysCEPCdpPortConfigTable | A table of per port configuration for Convergence End Point detection related to
the Cisco CDP protocol. Only ports that are capable of participating in Cisco CDP
protocol are represented in this table. Not-accessible. |
|
| etsysCEPCdpPortConfigEntry | An entry containing per port Convergence End Point data. Only interfaces that are
able to detect Convergence End Points are represented in this
table. Not-accessible. |
|
| etsysCEPCiscoCDPVoicePortVlan | This object controls the behavior of the remote
configuration of Cisco VOIP phones via Cisco CDP. Setting this object to a value of -1
will cause the device to not attempt to remotely configure a Cisco phone using CDP.
Setting this object to a value of 0 will cause the device to configure the phone to
send 802.1p priority tagged frames. A value of 4095 will cause the device to configure
the phone to send untagged frames. A value in the range 1..4094 will cause the device
to configure the phone to send 802.1Q tagged frames using that value as the
VLAN ID encoded in the tag. This object SHOULD be
maintained across device reboots. Read-write. |
|
| etsysConvEndPointGlobalConfigGroup | Objects which provide global control of the Convergence End Point
features. Status = deprecated. |
|
| etsysConvEndPointConfigGroup | Objects which provide overrides to the global Convergence End Point controls.
Status = current. |
|
| etsysConvEndPointDetectionGroup | Objects that provide configuration information specific to IP, port, and address
based Convergence End Point detection. Status = deprecated. |
|
| etsysConvEndPointStatusGroup | Objects that provide status information for discovered and detected Convergence
End Points. Status = deprecated. |
|
| etsysConvEndPointStatusGroup2 | Objects that provide status information for discovered and detected Convergence
End Points. Status = current. |
|
| etsysConvEndPointDetectionGroup2 | Objects that provide configuration information specific to IP, port, and address
based Convergence End Point detection Status = current. |
|
| etsysConvEndPointPortConfigGroup | Objects that provide per port control for discovered and detected Convergence End
Points. Status = current. |
|
| etsysConvEndPointCiscoVoiceVLANGroup | Objects that provide per port control for configuring Cisco VOIP phones via Cisco
CDP. Status = current. |
|
| etsysConvEndPointGlobalConfigGroup2 | Objects which provide global control of the Convergence End Point features.
Status = current. |