# create vman vm1 configure vman vm1 add ports 3 cep cvid 2 – 3 create vpls vsi1 fec-id-type pseudo-wire 35 configure vpls vsi1 add peer 192.168.0.2 core configure vpls vsi1 add service vman vm1
Here is an example:
# show vpls vsi1
L2VPN Name VPN ID Flags Services Name Peer IP State Flags
------------ ------ ------- -------------- --------------- ----- ------
VSI1 35 EAX--L- vm1 192.168.0.2 Up C---V-
VPN Flags: (E) Admin Enabled, (A) Oper Enabled, (I) Include Tag,
(X) Exclude Tag, (T) Ethertype Configured,
(V) VCCV HC Enabled, (W) VPN Type VPWS, (L) VPN Type
VPLS, (M) CFM MIP Configured
Peer Flags:(C) Core Peer, (S) Spoke Peer, (A) Active Core,
(p) Configured Primary Core, (s) Configured Secondary Core,
(N) Named LSP Configured, (V) VCCV HC Capabilities Negotiated,
(F) VCCV HC Failed
# show vpls vsi1 detail
L2VPN Name: VSI1
VPN ID : 35 Admin State : Enabled
Source Address : 192.168.0.1 Oper State : Enabled
VCCV Status : Disabled MTU : 1500
VCCV Interval Time : 5 sec. Ethertype : 0x88a8
VCCV Fault Multiplier : 4 .1q tag : exclude
L2VPN Type : VPLS Redundancy : None
Service Interface : vm1
Peer IP: 192.168.0.2
PW State : Up
PW Uptime : 0d:0h:4m:20s
PW Installed : True
Local PW Status : No Faults
Remote PW Status : No Faults
Remote I/F MTU : 1500
PW Mode : Core-to-Core
Transport LSP : LDP LSP (Not Configured)
Next Hop I/F : vlan2
Next Hop Addr : 11.0.2.2 Tx Label : 0x00173
PW Rx Label : 0x00174 PW Tx Label : 0x00174
PW Rx Pkts : 185920064 PW Tx Pkts : 186031288
PW Rx Bytes : 16732807110 PW Tx Bytes : 16742817810
MAC Limit : No Limit
VCCV HC Status : Not Sending (VCCV Not Enabled For This L2VPN)
CC Type : Rtr Alert Total Pkts Sent : 0
CV Type : LSP Ping Total Pkts Rcvd : 0
Send Next Pkt : --
Total Failures: 0 Pkts During Last Failure : 0
Last Failure Tm: --
1.26 # show vman vm1
VMAN Interface with name vm1 created by user
Admin State: Enabled Tagging:Untagged (Internal tag 4091)
Description: None
Virtual router: VR-Default
IPv4 Forwarding: Disabled
IPv4 MC Forwarding: Disabled
IPv6 Forwarding: Disabled
IPv6 MC Forwarding: Disabled
IPv6: None
STPD: None
Protocol: Match all unfiltered protocols
Loopback: Disabled
NetLogin: Disabled
OpenFlow: Disabled
QosProfile: None configured
Egress Rate Limit Designated Port: None configured
Flood Rate Limit QosProfile: None configured
Ports: 1. (Number of active ports=1)
CEP: *3: CVID 2-3
Flags: (*) Active, (!) Disabled, (g) Load Sharing port
(b) Port blocked on the vlan, (m) Mac-Based port
(a) Egress traffic allowed for NetLogin
(u) Egress traffic unallowed for NetLogin
(t) Translate VLAN tag for Private-VLAN
(s) Private-VLAN System Port, (L) Loopback port
(e) Private-VLAN End Point Port
(x) VMAN Tag Translated port
(G) Multi-switch LAG Group port
(H) Dynamically added by MVRP
(U) Dynamically added uplink port
(V) Dynamically added by VM Tracking