configure inline-power operator-limit ports

configure inline-power operator-limit [milliwatts | class-based] ports [all |port_list]

Description

Sets the power limit allowed for PDs connected to the specified ports.

Syntax Description


`milliwatts`	An integer specifying the maximum allowed power in milliwatts. Default is based on the port's class type (for example, 30W, 60W, 90W).
class-based	Specifies that the power limit is managed by the powered device's class.
`port_list`	Specifies one or more ports or slots and ports.

Default

This command is available on the ExtremeSwitching X440-G2, X450-G2, X460-G2, X465, and X620 series switches.—15,400 mW.

PoE+—30,000 mW.

PoE++ Type 3—60,000 mW.

PoE++ Type 4—90,000 mW.

Usage Guidelines

This command sets the power limit that a PD can draw on the specified ports. For PoE, the range is 3,000 to 16800mW and the default value is 15,400 mW. For PoE+, the range is 3,000 to 32,000 mW and the default value is 30,000 mW. For PoE++ Type 3, the range is 3,000 mW to 64,000 mW and the default value is 60,000 mW. For PoE++ Type 4, the range is 3,000 mW to 98,000 mW and the default value is 90,000 mW.

If the measured power for a specified port exceeds the port‘s operator limit, the power is withdrawn from that port and the port moves into a fault state.

If you try to set an operator-limit outside the accepted range, the system returns the following error message:

Error: Invalid operator-limit value. Must be in the range of 3000-90000 mW for PoE 802.3bt port

With a class-based operator-limit type, if a class4 PD is attached, then the operator-limit set will be ignored and the switch will not deliver more than 30W to the PD.

When class-based operator-limit is configured on a port, "Max Allowed Power" will show the maximum power for the class of the attached PD. Without the class-based option, "Max Allowed Power" will show the configured or default value of operator-limit.

Example

The following command sets the limit for legacy PDs on ports 3–6 of slot 5 on a SummitStack to 10000 mW:

configure inline-power operator-limit 10000 ports 5:3-5:6

History

This command was first available in ExtremeXOS 11.1.

PoE+ was added in ExtremeXOS 12.5.

PoE++ (Type 3) was added in ExtremeXOS 22.2.

PoE++ (Type 4) for 90W ports on ExtremeSwitching X465 (24W, 48W, 24MU-24W models) was added in ExtremeXOS 30.2.

The class-based option was added in ExtremeXOS 32.3.

Platform Availability

This command is available on:

PoE+

ExtremeSwitching X450-G2-24p-GE4—ExtremeXOS 16.1 and later.
ExtremeSwitching X450-G2-48p-GE4—ExtremeXOS 16.1 and later.
ExtremeSwitching X450-G2-24p-10GE4—ExtremeXOS 16.1 and later.
ExtremeSwitching X450-G2-48p-10GE4—ExtremeXOS 16.1 and later.
ExtremeSwitching X460-G2-24p-10GE4—ExtremeXOS 15.6 and later.
ExtremeSwitching X460-G2-48p-10GE4—ExtremeXOS 15.6 and later.
ExtremeSwitching X460-G2-24p-GE4—ExtremeXOS 15.6 and later.
ExtremeSwitching X460-G2-48p-GE4—ExtremeXOS 15.6 and later.
ExtremeSwitching X460-G2-16mp-32p-10GE4—ExtremeXOS 15.6 and later.
ExtremeSwitching X460-G2-24p-24hp-10GE4—ExtremeXOS 22.2 and later.
ExtremeSwitching X440-G2-48p-10GE4—ExtremeXOS 21.1 and later.
ExtremeSwitching X440-G2-24p-10GE4—ExtremeXOS 21.1 and later.
ExtremeSwitching X440-G2-12p-10GE4—ExtremeXOS 21.1 and later.
ExtremeSwitching X465-48P—ExtremeXOS 30.2 and later.
ExtremeSwitching X435-8P-4S—ExtremeXOS 30.5 and later.
ExtremeSwitching X435-24P-4S—ExtremeXOS 30.5 and later.
ExtremeSwitching X435-8P-2T-W—ExtremeXOS 30.5 and later.

PoE++

ExtremeSwitching X465-24MU-24W—ExtremeXOS 30.2 and later.
ExtremeSwitching X465-48W—ExtremeXOS 30.2 and later.
ExtremeSwitching X465-24MU—ExtremeXOS 30.2 and later.
ExtremeSwitching X465-24W—ExtremeXOS 30.2 and later.
ExtremeSwitching X465i-48W—ExtremeXOS 30.5 and later.