The following issues were resolved in ExtremeXOS 16.2.5-Patch1-3. ExtremeXOS 16.2.5-Patch1-3 includes all fixes up to and including ExtremeXOS 126.96.36.199, and earlier, ExtremeXOS 12.0.5, ExtremeXOS 12.1.7, ExtremeXOS 12.2.2-patch1-12, ExtremeXOS 12.3.6, ExtremeXOS 12.4.5, ExtremeXOS 12.5.5, ExtremeXOS 12.6.3, ExtremeXOS 12.6.5, ExtremeXOS 12.7.1, ExtremeXOS 15.1.5, ExtremeXOS 15.2.4, ExtremeXOS 15.3.3, ExtremeXOS 15.4.1, ExtremeXOS 15.5.1, ExtremeXOS 15.5.2, ExtremeXOS 15.6.1, ExtremeXOS 15.6.2, ExtremeXOS 15.7.1, ExtremeXOS 16.1, ExtremeXOS 16.1.2, ExtremeXOS 16.1.3, ExtremeXOS 16.2, ExtremeXOS 16.2.2, ExtremeXOS 16.2.3, ExtremeXOS 16.2.4, and ExtremeXOS 16.2.5. For information about those fixes, see the release notes for the specific release.
|Short loop occurs in EAPS with shared ports after link failure recovery.
|If client port information is missing for some DHCP snooping entries, "FDB lookup failed" errors appear while uploading DHCP bindings.
|NetLogin users are authenticated to random destinations when destination VLAN attributes from the RADIUS server are not received.
|Policy Manager cannot configure flood groups when the rate-limit is already configured through CLI.
|The mirroring configuration show in show configuration appears incorrectly if VLAN tag is used to add a VLAN to mirroring.
|CLI should restrict configuring IPv6 addresses on network and subscriber VLANs in PVLAN/VLAN aggregation.
|RADIUS/TACACS configurations are lost after rebooting if the VLAN interface gets IP address from DHCP server.
|Add support to configure ping success for ESRP track-ping.
|LSP takes a longer time (320 seconds) to switch over from primary path (strict) to secondary path (dynamic).
|The command enable bgp neighbor <neighbor IP> remove-private-AS-number is not removing 32-bit private AS-numbers.
|SNMP process ends unexpected with signal 11 when switch tries to delete the trap receiver from the inactive queue, but the trap receiver is already deleted from the queue by SNMP.
|STP loop protect stays in "Forwarding" state instead of "Listening" state even though it did not receive any BPDU from peer device.
|Router LSAs are dropped if they contains more than 400+ links.
|PTPV2 process ends unexpectedly with signal 5 when rebooting the switch with Network Timing license enabled.
|IGMPv3 membership report packets are malformed on egress PE while sending over VPLS pseudowire.
|UDP profile with VLAN action does not work when VLAN names are entered in a case-insensitive manner.
|Memory leak occur in MPLS process when accessing ExtremePwLspOutboundMappingEntry and ExtremePwPerfEntry SNMP OID.
|In the output of the show mirror command, maximum supported egress instance should be updated to 1 for ExtremeSwitching X440-G2 and X620 series switches.
|With BFD enabled in OSPF interfaces, traffic convergence time for OSPF learned routes is high during failover.
|After rebooting the switch with default configuration, some of the optional TLVs are not transmitted in LLDP packets.
|E4G-200 Series Switches
|Idmgr process ends unexpectedly with signal 11 in E4G-200 series switches, when enabling it through the enable identity-management command.
|Summit X460-G2 Series Switches
|On Summit X460-G2 series switches, packets are not transmitted out of the VIM-2t or VIM-2x ports configured for 1G speed after rebooting.
|BlackDiamond 8800 Series Switches
|Link does not come up with 100FX optics attached.
|Rate limit out-of profile actions such as log, disable port, and trap, are not triggered for ports on G48Xc modules.