This chapter summarizes the supported limits in ExtremeXOS 22.7.5.
For more information about licenses, see ExtremeXOS 22.7 Feature License Requirements .
The following tables summarize tested metrics for a variety of features, as measured in a per-system basis unless otherwise noted. These limits may change, but represent the current status. The contents of this table supersede any values mentioned in the ExtremeXOS books.
The scaling and performance information shown in the following tables is provided for the purpose of assisting with network design. It is recommended that network architects and administrators design and manage networks with an appropriate level of network scaling “head room.” The scaling and performance figures provided have been verified using specific network topologies using limited switch configurations. There is no guarantee that the scaling and performance figures shown are applicable to all network topologies and switch configurations and are provided as a realistic estimation only. If you experience scaling and performance characteristics that you feel are sufficiently below what has been documented, contact Extreme Networks technical support for additional assistance.
The route limits shown in the following tables for IPv4 and IPv6 routing protocols are software limits only. The actual hardware limits may be higher or lower than the software limits, based on platform. The hardware limits for specific platforms are specified as "IPv4/IPv6 routes (LPM entries in hardware)" in the following tables.
In the Extended Edge Switching architecture, Layer-2, Layer-3, and multicast packet forwarding and filtering operations take place on the controlling bridge. The controlling bridge switch and attached BPEs (V400 Virtual Port Extenders) constitute a single, extended switch system. Therefore, the Extended Edge Switching system assumes the scale and limits from the specific controlling bridge model (for example, Summit X670-G2 or ExtremeSwitching X690 and X590 series switches) in use. For applicable limits, see the following tables for the controlling bridge you are using.
The following table shows supported limits for features in the Edge License.
| Metric | Product | Limit |
|---|---|---|
| AAA (local)—maximum number of admin and local user accounts. | All platforms | 16 |
| Access lists (meters)—maximum number of meters. | ExtremeSwitching X620, X440-G2 | 1,024 ingress 256 egress |
| Summit X770, X670-G2, X450-G2, X460-G2 | 1,024 ingress 512 egress |
|
| ExtremeSwitching X870, X690, X590 | 2,048 ingress 512 egress |
|
| Access lists (policies)—suggested maximum number of lines in a single policy file. | All platforms | 300,000 |
| Access lists (policies)—maximum number of rules in a single policy file.a | Summit X460-G2, X450-G2, X770, X670-G2 | 4,096 ingress 1,024 egress |
| ExtremeSwitching X620, X440-G2 | 2,048 ingress 512 egress |
|
| ExtremeSwitching X870 | 3,072 ingress 1,024 egress |
|
| ExtremeSwitching X690, X590 | 8,192 ingress 1,024 egress |
|
| Access lists (policies)—maximum number of rules in a single policy file in first stage (VFP). | Summit X450-G2, X460-G2 | 2,048 ingress only |
| Summit X670-G2, X770, ExtremeSwitching X870, X690 | 1,024 ingress only | |
|
ExtremeSwitching X620, X440-G2 |
512 ingress only |
|
| ExtremeSwitching X590 | 2,048 ingress only | |
| Access lists (slices)—number of ACL slices. | Summit X460-G2, X450-G2 | 16 ingress 4 egress |
| Summit X770, X670-G2, ExtremeSwitching X690, X590 | 12 ingress 4 egress |
|
| ExtremeSwitching X440-G2, X620 | 8 ingress 4 egress |
|
| ExtremeSwitching X870 | 4 ingress 4 egress |
|
| Access lists (slices)—number of ACL slices in first stage (VFP). | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 4 ingress only |
| ACL Per Port Meters—number of meters supported per port. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 16 |
| ACL port ranges | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 32 |
| Meters Packets-Per-Second Capable | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | Yes |
| AVB (audio video bridging)—maximum number of active streams. | Summit X450-G2, X460-G2, X770, and ExtremeSwitching X620, X440-G2 | 1,024 |
| Summit X670-G2 | 4,096 | |
| ExtremeSwitching X590, X690, X870 | N/A | |
| BFD sessions (Software Mode)—maximum number of BFD sessions. | Summit X460-G2, X670-G2, X450-G2, X770, ExtremeSwitching X440-G2, X620, X870, X690, X590 (default timers—1 sec) | 512 |
| Summit X460-G2, X670-G2, X450-G2, X770, ExtremeSwitching X440-G2, X620, X870, X690, X590 (minimal timers—100 msec) | 10c | |
| BFD IPv4 sessions (Hardware Assisted)—maximum number of IPv4 BFD sessions. | Summit X460-G2, ExtremeSwitching X870, X690, X590 | 900 (PTP not enabled) 425 (PTP enabled) 256 (with 3 ms transmit interval) |
| BFD IPv6 sessions (Hardware Assisted)—maximum number of IPv6 BFD sessions. | Summit X460-G2, ExtremeSwitching X870, X690, X590 | 425 (PTP not enabled) |
| BOOTP/DHCP relay—maximum number of BOOTP or DHCP servers per virtual router. | Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 8 |
| BOOTP/DHCP relay—maximum number of BOOTP or DHCP servers per VLAN. | Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 8 |
| BOOTP/DHCP relay—maximum number of DHCPv4/v6 relay agents | Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 4,000 |
| Connectivity fault management
(CFM)—maximum number or CFM domains. Note: With Advanced Edge license or higher.
|
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 8 |
| CFM—maximum number of CFM
associations. Note: With Advanced Edge license or higher.
|
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 256 |
| CFM—maximum number of CFM
up end points. Note: With Advanced Edge license or higher.
|
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 32 |
| CFM—maximum
number of CFM down end points. Note: With Advanced Edge license or higher.
|
Summit X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 32 |
| Summit X460-G2 | 256 (non-load shared ports) 32 (load shared ports) |
|
| CFM—maximum number of CFM
remote end points per up/down end point. Note: With Advanced Edge license or higher.
|
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 2,000 |
| CFM—maximum number of
dot1ag ports. Note: With Advanced Edge license or higher.
|
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 128 |
| CFM—maximum number of CFM
segments. Note: With Advanced Edge license or higher.
|
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 1,000 |
| CFM—maximum number of
MIPs. Note: With Advanced Edge license or higher.
|
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 256 |
| CLEAR-Flow—total number of rules supported. The ACL rules plus CLEAR-Flow rules must be less than the total number of supported ACLs. | Summit X460-G2, X770, X670-G2, X450-G2 | 4,094 |
| ExtremeSwitching X440-G2, X620 | 1,024 | |
| ExtremeSwitching X870 | 3,072 | |
| ExtremeSwitching X690, X590 | 8,192 | |
| Data Center Bridging eXchange (DCBX) protocol Type Length Value (TLVs)—maximum number of DCBX application TLVs. | Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 8 |
| DHCPv6 Prefix Delegation Snooping—Maximum number of DHCPv6 prefix delegation snooped entries. | Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 256 (with Underlying Protocol Ripng) 128 (with Underlying protocol OSPFv3) 1,024 (with static routes) |
| DHCP snooping entries—maximum number of DHCP snooping entries. | Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 2,048 |
| Dynamic
ACLs—maximum number of ACLs processed per second. Note: Limits are load-dependent.
|
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | |
|
|
|
| EAPS domains—maximum
number of EAPS domains. Note: An EAPS ring that is being spatially reused cannot have
more than four configured EAPS domains.
Note: You can increase the number of domains by upgrading to the
Advanced Edge license.
|
Summit X670-G2, X450-G2, X460-G2, X770,and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 4 |
| EAPSv1 protected VLANs—maximum number of protected VLANs. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2 | 1,000 |
| ExtremeSwitching X870, X690, X590 | 2,000 | |
| ERPS domains—maximum
number of ERPS domains with or without CFM configured. Note: You can increase the number of domains by upgrading to the
Advanced Edge license.
|
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 4 |
| ERPSv1 protected VLANs—maximum number of protected VLANs. | ExtremeSwitching X870, X690, X590 | 2,000 |
| Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X620, X440-G2 | 1,000 | |
| ERPSv2 protected VLANs—maximum number of protected VLANs. | Summit X450-G2, X460-G2, X670-G2, and ExtremeSwitching X870, X690, X590 | 2,000 |
| Summit X770, ExtremeSwitching X620, X440-G2 | 500 | |
| ELSM (vlan-ports)—maximum number of VLAN ports. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X870, X690, X590 |
5,000 |
| ExtremeSwitching X440-G2 | 4,000 | |
| Extended Edge Switching maximum BPEs—maximum number of attached bridge port extenders (BPEs). | Summit X670-G2, ExtremeSwitching X690, X590 | 48 |
| Extended Edge Switching maximum BPEs per ring—maximum number of attached bridge port extenders (BPEs) per ring. | Summit X670-G2, ExtremeSwitching X690, X590 | 8 |
| Extended Edge Switching maximum cascade ports—maximum number of upstream ports on bridge port extenders (BPEs). | Summit X670-G2, ExtremeSwitching X690, X590 |
2 on V400-24 models 4 on V400-48 models |
| Extended Edge Switching maximum tiers—maximum number of cascade levels (tiers) of bridge port extenders (BPEs). | Summit X670-G2, ExtremeSwitching X690, X590 | 4 |
| Extended Edge Switching VLAN+ port memberships—maximum number of VLAN+ (extended) port memberships. | Summit X670-G2, ExtremeSwitching X690, X590 |
12,000 in hash mode (default) 131,000 in port-group mode |
| Forwarding rate—maximum L3 software forwarding rate. | ExtremeSwitching X690, X590 | 30,000 pps |
| ExtremeSwitching X870 | 32,000 pps | |
| Summit X450-G2 | 16,000 pps | |
| Summit X460-G2 | 17,000 pps | |
| ExtremeSwitching X620 | 10,000 pps | |
| Summit X670-G2 | 15,000 pps | |
| Summit X770 | 6,500 pps | |
| ExtremeSwitching X440-G2 | 9,000 pps | |
| FDB (unicast blackhole entries)—maximum number of unicast blackhole FDB entries. | Summit X460-G2 | 49,152f |
| Summit X770, X670-G2 | 294,912f | |
| Summit X450-G2 | 34,816f | |
| ExtremeSwitching X620, X440-G2 | 16,384f | |
| ExtremeSwitching X870 | 139,264f | |
| ExtremeSwitching X690, X590 | 278,528f | |
| FDB (multicast blackhole entries)—maximum number of multicast blackhole FDB entries. | Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2, X620 | 1,024 |
| Summit X770, X670-G2, ExtremeSwitching X870, X690, X590 | 4,096 | |
| FDB (maximum L2 entries)—maximum number of MAC addresses. | Summit X460-G2 | 98,300g |
| Summit X770, X670-G2 | 294,912g | |
| Summit X450-G2 | 68,000g | |
| ExtremeSwitching X620, X440-G2 | 16,384 | |
| ExtremeSwitching X870 | 139,264g | |
| ExtremeSwitching X690, X590 | 278,528g | |
| FDB (Maximum L2 entries)—maximum number of multicast FDB entries. | Summit X770, X670-G2, ExtremeSwitching X870, X690, X590 | 4,096 |
| Summit X450-G2, X460-G2, and ExtremeSwitching X620, X440-G2 | 1,024 | |
| Identity management—maximum number of Blacklist entries. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 512 |
| Identity management—maximum number of Whitelist entries. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 512 |
| Identity management—maximum number of roles that can be created. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 64 |
| Identity management—maximum role hierarchy depth allowed. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 5 |
| Identity management—maximum number of attribute value pairs in a role match criteria. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 16 |
| Identity management—maximum of child roles for a role. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 8 |
| Identity management—maximum number of policies/dynamic ACLs that can be configured per role. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 8 |
| Identity management—maximum number of LDAP servers that can be configured. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 8 |
| Identity management—maximum number of Kerberos servers that can be configured. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 20 |
| Identity management—maximum database memory-size. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 512 |
| Identity
management—recommended number of identities per switch. Note: Number of identities per switch is for a default identity
management database size (512 Kbytes) across all platforms.
|
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 100 |
| Identity
management—recommended number of ACL entries per identity. Note: Number of ACLs per identity, based on system ACL
limitation.
|
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 20 |
| Identity management—maximum number of dynamic ACL entries configured as an individual dynamic rule, or as an ACL entry in a policy file. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 500 |
| IGMP snooping per VLAN filters—maximum number of VLANs supported in per-VLAN IGMP snooping mode. | Summit X460-G2, ExtremeSwitching X870 | 1,500 |
| Summit X450-G2 | 2,048 | |
| Summit X770, X670-G2 | 2,000 | |
| ExtremeSwitching X620, X440-G2 | 1,000 | |
| ExtremeSwitching X690, X590 | 4,000 | |
| IGMPv1/v2 SSM-map entries—maximum number of IGMPv1/v2 SSM mapping entries. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 500 |
| IGMPv1/v2 SSM-map entries—maximum number of sources per group in IGMPv1/v2 SSM mapping entries. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 50 |
| IGMPv2 subscriber—maximum number of IGMPv2 subscribers per port.n | Summit X770, X670-G2, X460-G2, X450-G2 | 4,000 |
| ExtremeSwitching X440-G2, X620 | 3,500 | |
| ExtremeSwitching X870, X690, X590 | 4,000 | |
| IGMPv2 subscriber—maximum number of IGMPv2 subscribers per switch.n | Summit X770, X670-G2 | 30,000 |
| Summit X460-G2, X450-G2 | 20,000 | |
| ExtremeSwitching X620, X440-G2 | 17,500 | |
| ExtremeSwitching X870, X690, X590 | 45,000 | |
| IGMPv3 maximum source per group—maximum number of source addresses per group. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 250 |
| IGMPv3 subscriber—maximum number of IGMPv3 subscribers per port.n | Summit X770, X670-G2, X460-G2, X450-G2 | 4,000 |
| ExtremeSwitching X440-G2, X620 | 3,500 | |
| ExtremeSwitching X870, X690, X590 | 4,000 | |
| IGMPv3 subscriber—maximum number of IGMPv3 subscribers per switch.n | Summit X460-G2, X450-G2 | 20,000 |
| Summit X770, X670-G2 | 30,000 | |
| ExtremeSwitching X620, X440-G2 | 17,500 | |
| ExtremeSwitching X870, X690, X590 | 45,000 | |
| IP ARP entries
in software—maximum number of IP ARP entries in software. Note: Might be limited by hardware capacity of FDB (maximum L2
entries).
|
Summit X670-G2, X770 | 131,072 (up to)h |
| Summit X460-G2 | 57,344 (up to)h | |
| Summit X450-G2 | 47,000 (up to)h | |
| ExtremeSwitching X440-G2, X620 | 20,480 | |
| ExtremeSwitching X870 | 94,206 (up to)h | |
| ExtremeSwitching X690, X590 | 157,694 (up to) h | |
| IPv4 ARP entries in hardware with minimum LPM routes—maximum recommended number of IPv4 ARP entries in hardware, with minimum LPM routes present. Assumes number of IP route reserved entries is 100 or less. | ExtremeSwitching X870 | 74,000 (up to)h |
| Summit X460-G2 | 50,000 (up to)h | |
| Summit X770, X670-G2 | 108,000 (up to)h | |
| Summit X450-G2 | 39,000 (up to)h | |
| ExtremeSwitching X620 | 1,500 | |
| ExtremeSwitching X440-G2 | 1,000 | |
| ExtremeSwitching X690, X590 | 119,000 (up to) h | |
| IPv4 ARP entries in hardware with maximum LPM routes—maximum recommended number of IPv4 ARP entries in hardware, with maximum LPM routes present. Assumes number of IP route reserved entries is “maximum.” | ExtremeSwitching X870 | 64,000 (up to)h |
| Summit X460-G2 | 43,000 (up to)h | |
| Summit X770, X670-G2 | 98,000 (up to)h | |
| Summit X450-G2 | 29,000 (up to)h | |
| ExtremeSwitching X620 | 1,500 | |
| ExtremeSwitching X440-G2 | 1,000 | |
| ExtremeSwitching X690, X590 | 109,000 (up to) h | |
| IP flow information export (IPFIX)—number of simultaneous flows. | Summit X460-G2 | 2,048 ingress 2,048 egress |
| Summit X450-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | N/A | |
| IPv4 remote hosts in hardware with zero LPM routes—maximum recommended number of IPv4 remote hosts (hosts reachable through a gateway) in hardware when LPM routing is not used. Assumes number of IP route reserved entries is 0, and number of IPv4 ARP entries present is 100 or less. | ExtremeSwitching X870 | 120,000 (up to)h |
| Summit X460-G2 | 73,000h | |
| Summit X770, X670-G2 | 176,000 (up to)h | |
| Summit X450-G2 | 61,000 (up to)h | |
| ExtremeSwitching X440-G2, X620 | 3,500 | |
| ExtremeSwitching X690, X590 | 216,000 (up to) h | |
| IPv4 routes—maximum number of IPv4 routes in software (combination of unicast and multicast routes), including static and from all routing protocols. | Summit X460-G2, X450-G2, X440-G2, X620 | 25,000 |
| Summit X670-G2, ExtremeSwitching X690, X870, X590 | 131,000 | |
| Summit X770 | 100,000 | |
| IPv4 routes (LPM entries in hardware)— number of IPv4 routes in hardware. | Summit X460-G2 | 12,000 |
| Summit X450-G2 | 16,000 | |
| Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 | 131,000 q | |
| ExtremeSwitching X620, X440-G2 | 480 | |
| IPv6 6in4 tunnel—maximum number of IPv6 6in4 tunnels. | Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 255 |
| ExtremeSwitching X440-G2, X620 | N/A | |
| IPv6 6to4 tunnel—maximum number of IPv6 6to4 tunnels. | Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 1 (per virtual router) |
| ExtremeSwitching X440-G2, X620 | N/A | |
| IPv6 addresses on an interface—maximum number of IPv6 addresses on an interface. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 255 |
| IPv6 addresses on a switch—maximum number of IPv6 addresses on a switch. | Summit X770, X670-G2, X460-G2, X450-G2, ExtremeSwitching X870, X690, X590 | 2,048 |
| ExtremeSwitching X620, X440-G2 | 510 | |
| IPv6 host entries in hardware—maximum number of IPv6 neighbor entries in hardware. | Summit X770, X670-G2 | 36,750 h |
| Summit X460-G2 | 22,000h | |
| Summit X450-G2 | 12,000h | |
| ExtremeSwitching X440-G2 | 1,000 | |
| ExtremeSwitching X620 | 1,500 | |
| ExtremeSwitching X690, X590 | 24,500h | |
| ExtremeSwitching X870 | 22,000h | |
| IPv6 routes in software—maximum number of IPv6 routes in software, including static routes and routes from all routing protocols. | Summit X450-G2, X460-G2, and ExtremeSwitching X620, X440-G2 | 25,000 |
| Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 | 65,000 q | |
| IPv6 routes (LPM entries in hardware)—maximum number of IPv6 routes in hardware. | Summit X460-G2 | 6,000 |
| Summit X450-G2 | 8,000 | |
| Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 |
65,000q |
|
| ExtremeSwitching X620, X440-G2, | 240 | |
| IPv6 routes with a mask greater than 64 bits in hardware—maximum number of such IPv6 LPM routes in hardware. | Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 | 8,192 r |
| ExtremeSwitching X440-G2, X620 | 1,024 | |
| Summit X450-G2, X460-G2 | 2,048 | |
| IPv6 route sharing in hardware—route mask lengths for which ECMP is supported in hardware. | Summit X460-G2, X450-G2, and ExtremeSwitching X620 |
0–64 >64 single path only |
| Summit X670-G2, X770, and ExtremeSwitching X690, X870, X590 | 0–128r | |
| ExtremeSwitching X440-G2 | Not supported | |
| IP router interfaces—maximum number of VLANs performing IPv4 and/or IPv6 routing. Excludes sub-VLANs. | Summit X460-G2, X770, X670-G2, X450-G2, ExtremeSwitching X870, X690, X590 | 2,048 |
| ExtremeSwitching X620, X440-G2 | 510 | |
| IP multicast static routes—maximum number of permanent multicast IP routes. | Summit X460-G2, X670-G2, X450-G2, X770, ExtremeSwitching X870, X690, X590 | 1,024 |
| IP unicast static routes—maximum number of permanent IP unicast routes. | Summit X460-G2, X670-G2, X450-G2, X770, ExtremeSwitching X870, X690, X590 | 1,024 |
| ExtremeSwitching X620, X440-G2 | 480 | |
| IP route sharing (maximum gateways)—Configurable maximum number of gateways used by equal cost multipath OSPF, BGP, IS-IS, static routes, or L2VPNs. Static routes, OSPF, and BGP are limited to 64 ECMP gateways per destination, while IS-IS is limited to 8. L2VPNs are limited to 16 LSPs per pseudowire on platforms that support 32 gateways, and 64 LSPs per pseudowire on platforms that support 64 gateways. | Summit X460-G2, X670-G2, X450-G2, X770, and ExtremeSwitching X620, X870, X690, X590 | 2, 4, 8, 16, 32, or 64 |
| ExtremeSwitching X440-G2 | N/A | |
| IP route sharing (total combinations of gateway sets)—maximum number of combinations of sets of adjacent gateways used by multipath OSPF, BGP, IS-IS, or static routes. | Summit X670-G2, X770 | |
|
|
|
| Summit X460-G2, X450-G2 | ||
|
|
|
| ExtremeSwitching X620 | ||
|
|
|
| ExtremeSwitching X690, X590 | ||
Note: The values here represent the maximum attainable ECMP
groups of which, due to the RIOT feature, half are reserved for overlay and half for underlay
routing. For more information about RIOT, see the
ExtremeXOS 22.7 User Guide
.
|
|
|
| ExtremeSwitching X870 | ||
|
|
|
| ExtremeSwitching X440-G2 | N/A | |
| IP multinetting (secondary IP addresses)—maximum number of secondary IP addresses per VLAN. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 255 |
| Jumbo frames—maximum size supported for jumbo frames, including the CRC. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 9,216 |
| L2 VPN: VCCV (pseudowire Virtual Circuit Connectivity Verification) VPNs per switch—maximum number of VCCV enabled VPLS VPNs. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 16 |
| Summit X450-G2, and ExtremeSwitching X620, X440-G2 | N/A | |
| L2 VPN: VPLS MAC addresses—maximum number of MAC addresses learned by a switch. | Summit X770 | 128,000 |
| Summit X670-G2, ExtremeSwitching X690, X590 | 140,000 | |
| Summit X460-G2 | 55,000 | |
| ExtremeSwitching X870 | 65,000 | |
| Summit X450-G2, and ExtremeSwitching X620, X440-G2 | N/A | |
| L2 VPN: VPLS VPNs—maximum number of VPLS virtual private networks per switch. | Summit X460-G2, X770, X670-G2, ExtremeSwitching X870, X690, X590 | 1,023 |
| Summit X450-G2, and ExtremeSwitching X620, X440-G2 | N/A | |
| L2 VPN: VPLS peers—maximum number of VPLS peers per VPLS instance. | Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 64 |
| Summit X450-G2, and ExtremeSwitching X620, X440-G2 | N/A | |
| L2 VPN: LDP pseudowires—maximum number of pseudowires per switch. | Summit X770, X670-G2, X460-G2, and ExtremeSwitching X870, X690, X590 | 7,000 |
| Summit X450-G2, and ExtremeSwitching X620, X440-G2 | N/A | |
| L2 VPN: static pseudowires—maximum number of static pseudowires per switch. | Summit X670-G2, X460-G2, X770, ExtremeSwitching X870, X690, X590 | 7,000 |
| Summit X450-G2, and ExtremeSwitching X620, X440-G2 | N/A | |
| L2 VPN: Virtual Private Wire Service (VPWS) VPNs—maximum number of virtual private networks per switch. | Summit X670-G2, ExtremeSwitching X870, X690, X590 | 4,090 |
| Summit X460-G2 | 1,023 | |
| Summit X770 | 4,000 | |
| Summit X450-G2, and ExtremeSwitching X620, X440-G2 | N/A | |
| Layer-2 IPMC forwarding
caches—(IGMP/MLD/PIM snooping) in mac-vlan mode. Note:
|
Summit X770, X670-G2 | 73,000 |
| Summit X460-G2 | 24,000 | |
| Summit X450-G2 | 14,000 | |
| ExtremeSwitching X620, X440-G2 | 5,000 | |
| ExtremeSwitching X870 | 36,000 | |
| ExtremeSwitching X690, X590 | 67,000 | |
| Layer-3 IPv4 Multicast—maximum
number of <S,G,V> entries installed in the hardware (IP multicast compression
enabled). Note:
|
Summit X460-G2 | 26,000 |
| Summit X450-G2 | 21,000 | |
| Summit X770, X670-G2 | 77,500 | |
| ExtremeSwitching X620, X440-G2 | 1,500 | |
| ExtremeSwitching X870 | 52,000 | |
| ExtremeSwitching X690, X590 | 93,000 | |
| Layer-3 IPv6 Multicast—maximum
number of <S,G,V> entries installed in the hardware (IP multicast compression
enabled). Note:
|
Summit X770, X670-G2 | 30,000 |
| Summit X460-G2 | 14,000 | |
| Summit X450-G2 | 10,000 | |
| ExtremeSwitching X620, X440-G2 | 700 | |
| ExtremeSwitching X870 | 18,000 | |
| ExtremeSwitching X690, X590 | 48,000 | |
| Load sharing—maximum
number of load sharing groups. Note: The actual number of load-sharing groups that can
be configured is limited by the number of physical ports present in the switch or
SummitStack.
|
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 128 |
| Load sharing—maximum number of ports per load-sharing group. | For standalone and stacked: ExtremeSwitching X620, X440-G2 | 8 |
| For standalone: Summit X770, X670-G2, X460-G2, X450-G2, ExtremeSwitching X870, X690, X590 | 32 | |
| For stacked: Summit X770, X670-G2, X460-G2, X450-G2, X670-G2, and ExtremeSwitching X870, X690, X590 | 64 | |
| Logged messages—maximum number of messages logged locally on the system. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 20,000 |
| MAC-based security—maximum number of MAC-based security policies. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 1,024 |
| MAC Locking—Maximum number of MAC locking stations that can be learned on a port. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
64 (static MAC locking stations) 600 (first arrival MAC locking stations) |
| Meters—maximum number of meters supported. | Summit X460-G2, X450-G2, X670-G2, X770, ExtremeSwitching X440-G2, X620, X870, X690, X590 | 2,048 |
| Maximum mirroring instances | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 TableOtherOnly two or four mirroring
instances will be active at a time, depending on the mirroring filter added to it. There are
four hardware resource slots. Each single instance uses one such slot, while each ingress plus
egress instance uses two slots. You can use a total of four slots, while there are no more
than two egress instances. The maximum possible combination for mirroring instances:
|
16 (including default mirroring instance) |
| ExtremeSwitching X620, X440-G2 Note: For stacks containing X620 or X440-G2, maximum supported egress
mirror instances is 1.
|
1 (egress) | |
| Mirroring
(filters)—maximum number of mirroring filters. Note: This is the number of filters across all the active mirroring
instances.
|
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 128 |
| Mirroring, one-to-many
(filters)—maximum number of one-to-many mirroring filters. Note: This is the number of filters across all the active mirroring
instances.
|
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 128 |
| Mirroring, one-to-many (monitor port)—maximum number of one-to-many monitor ports. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 16 |
| MLAG ports—maximum number of MLAG ports allowed. | Summit X670-G2, ExtremeSwitching X690 | 71 |
| ExtremeSwitching X440-G2, Summit X450-G2 | 51 | |
| Summit X460-G2 | 53 | |
| Summit X770 | 103 | |
| ExtremeSwitching X620 | 15 | |
| ExtremeSwitching X870 | 127 | |
| ExtremeSwitching X590 | 35 | |
| MLAG peers—maximum number of MLAG peers allowed. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 2 |
| MPLS RSVP-TE interfaces—maximum number of interfaces. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690 | 32 |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS RSVP-TE ingress LSPs—maximum number of ingress LSPs. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690 | 2,000 |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS RSVP-TE egress LSPs—maximum number of egress LSPs. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690 | 2,000 |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS RSVP-TE transit LSPs—maximum number of transit LSPs. | Summit X460-G2, X670-G2, X770 | 2,000 |
| ExtremeSwitching X870, X690 | 4,000 | |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS RSVP-TE paths—maximum number of paths. | Summit X460-G2, X770 | 1,000 |
| Summit X670-G2, ExtremeSwitching X870, X690 | 2,000 | |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS RSVP-TE profiles—maximum number of profiles. | Summit X460-G2, X770 | 1,000 |
| Summit X670-G2, ExtremeSwitching X870, X690 | 2,000 | |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS RSVP-TE EROs—maximum number of EROs per path. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690 | 64 |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS LDP peers—maximum number of MPLS LDP peers per switch. | Summit X770 | 64 |
| Summit X670-G2, X460-G2, ExtremeSwitching X870, X690 | 128 | |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS LDP adjacencies—maximum number of MPLS LDP adjacencies per switch. | Summit X460-G2 | 50 |
| Summit X770, X670-G2, ExtremeSwitching X870, X690 | 64 | |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS LDP ingress LSPs—maximum number of MPLS LSPs that can originate from a switch. | Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690 | 2,048 |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS LDP-enabled interfaces—maximum number of MPLS LDP configured interfaces per switch. | Summit X770 | 64 |
| Summit X670-G2, X460-G2, ExtremeSwitching X870, X690 | 128 | |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS LDP transit LSPs—maximum number of MPLS transit LSPs per switch. | Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690 | 4,000 |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS LDP egress LSPs—maximum number of MPLS egress LSPs that can terminate on a switch. | Summit X670-G2, X460-G2, X770, ExtremeSwitching X870, X690 | 4,000 |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS static egress LSPs—maximum number of static egress LSPs. | Summit X460-G2 | 7,116 |
| Summit X770, ExtremeSwitching X870, X690 | 8,000 | |
| Summit X670-G2 | 15,308 | |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS static ingress LSPs—maximum number of static ingress LSPs. | Summit X460-G2, ExtremeSwitching X870, X690 | 4,000 |
| Summit X770, X670-G2 | 2,048 | |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| MPLS static transit LSPs—maximum number of static transit LSPs | Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690 | 4,000 |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| Multicast listener discovery (MLD) snooping per-VLAN filters—maximum number of VLANs supported in per-VLAN MLD snooping mode. | Summit X460-G2, X770, X670-G2, ExtremeSwitching X870 | 1,200 |
| Summit X450-G2 | 512 | |
| ExtremeSwitching X620, X440-G2 | 600 | |
| ExtremeSwitching X690, X590 | 1,500 | |
| Multicast listener discovery (MLD)v1 subscribers—maximum number of MLDv1 subscribers per port.n | Summit X770, X670-G2, X450-G2, X460-G2 | 4,000 |
| ExtremeSwitching X620, X440-G2 | 3,500 | |
| ExtremeSwitching X870, X690, X590 | 4,000 | |
| Multicast listener discovery (MLD)v1 subscribers—maximum number of MLDv1 subscribers per switch.n | Summit X460-G2, X450-G2, ExtremeSwitching X620, X440-G2 | 10,000 |
| Summit X770, X670-G2 | 30,000 | |
| ExtremeSwitching X870, X690, X590 | 45,000 | |
| Multicast listener discovery (MLD)v2 subscribers—maximum number of MLDv2 subscribers per port.n | Summit X770, X670-G2, X460-G2, X450-G2 | 4,000 |
| ExtremeSwitching X620, X440-G2 | 3,500 | |
| ExtremeSwitching X870, X690, X590 | 4,000 | |
| Multicast listener discovery (MLD)v2 subscribers—maximum number of MLDv2 subscribers per switch.n | Summit X770, X670-G2 | 30,000 |
| Summit X460-G2, X450-G2, ExtremeSwitching X620, X440-G2 | 10,000 | |
| ExtremeSwitching X870, X690, X590 | 45,000 | |
| Multicast listener discovery (MLD)v2 maximum source per group—maximum number of source addresses per group. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 200 |
| Multicast listener discovery (MLD) SSM-map entries—maximum number of MLD SSM mapping entries. | Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 500 |
| ExtremeSwitching X440-G2, X620 | 50 | |
| Multicast listener discovery (MLD) SSM-MAP entries—maximum number of sources per group in MLD SSM mapping entries. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 50 |
| Network Login—maximum number of clients being authenticated on MAC-based VLAN enabled ports. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 1,024 |
| Network Login—maximum number of clients being authenticated with policy mode enabled with TCI overwrite enabled. | Summit X450-G2, X460-G2, ExtremeSwitching X590 | 1,024 |
| Summit X670-G2, X770, ExtremeSwitching X870, X690 | 512 | |
| ExtremeSwitching X620, X440-G2 | 256 | |
| Network Login—maximum number of dynamic VLANs. | Summit X460-G2, X450-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 2,000 |
| ExtremeSwitching X440-G2, X620 | 1,024 | |
| Network Login VLAN VSAs—maximum number of VLANs a client can be authenticated on at any given time. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 10 |
| Network Service Identifiers (NSI)/VLAN mappings—maximum number of VLANs to NSI mappings. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 94 |
| Node Alias—maximum number of entries per slot. | Summit X450-G2, X460-G2, X670-G2, X770 and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 8,192 |
| ONEPolicy Roles/Profiles—maximum number of policy roles/profiles. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 63 |
| ONEPolicy Rules per Role/Profile—maximum number of rules per role/policy. | Summit X450-G2, X460-G2 | IPv6 rules: 256 IPv4 rules: 256 L2 Rules: 184 MAC Rules: 256 |
| Summit X670-G2, X770, ExtremeSwitching X870 | IPv6 Rules: 256 L2 Rules: 184 MAC Rules: 256 IPv4 Rules: 256 |
|
| ExtremeSwitching X620, X440-G2 | IPv6 and Mac Rules: 0 Ipv4 Rules: 256 (per switch) L2 Rules: 184 (per switch) |
|
| ExtremeSwitching X690, X590 |
IPv4 Rules: 512 IPv6 Rules: 512 MAC Rules: 512 L2 Rules: 440 |
|
| ONEPolicy Authenticated Users per Switch—maximum number of authenticated users per port only with TCI-Overwrite enabled. | Summit X450-G2, X460-G2, and ExtremeSwitching X590 | 1,024 |
| Summit X670-G2, X770, ExtremeSwitching X690, X870 | 512 | |
| ExtremeSwitching X620, X440-G2 | 256 | |
| Stacking | Depends on the stack nodes. | |
| ONEPolicy
Authenticated Users per Switch—maximum number of authenticated users per
switch with TCI-Overwrite disabled. Note: The maximum values assume 75% utilization of VLAN-XLATE hash
table.
|
ExtremeSwitching X690, X590 | 24,576 |
| Summit X670-G2, X460-G2, ExtremeSwitching X870 | 12,288 | |
| Summit X770, X450-G2 | 6,144 | |
| ExtremeSwitching X620, X440-G2 | 1,536 | |
| Stacking | 1,536–65,534 | |
| ONEPolicy Authenticated Users per Port per Switch— maximum number of
authenticated users per port per switch with TCI overwrite disabled. Note: The maximum values assume 75% utilization of VLAN-XLATE hash
table.
|
Summit X450-G2, X770 | 6,144 |
| Summit 460-G2, X670-G2, and ExtremeSwitching X870 | 12,288 | |
| ExtremeSwtiching X690, X590 | 24,576 | |
| ExtemeSwtiching X440-G2, X620 | 1,536 | |
| ONEPolicy Authenticated Users per Port per Switch— maximum number of authenticated users per port with only with TCI-Overwrite enabled. | Summit X450-G2, X460-G2, ExtremeSwitching X590 | 1,024 |
| Summit X670-G2, X770, ExtremeSwitching X870, X690 | 512 | |
| ExtremeSwitching X620, X440-G2 | 256 | |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—total maximum number of unique permit/deny traffic classification rules types (system/stack). | Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870 | 952 |
| ExtremeSwitching X620, X440-G2 | 440 | |
| ExtremeSwitching X690, X590 | 1,976 | |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique MAC permit/deny traffic classification rules types (macsource/macdest). | Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870 | 256 |
| ExtremeSwitching X620, X440-G2 | N/A | |
| ExtremeSwitching X690, X590 | 512 | |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique IPv6 permit/deny traffic classification rules types (ipv6dest). | Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870 | 256 |
| ExtremeSwitching X620, X440-G2 | N/A | |
| ExtremeSwitching X690, X590 | 512 | |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique IPv4 permit/deny traffic classification rules (typesipsource / ipdest / ipfrag / udpsourceportIP / udpdestportIP / tcpsourceportIP / tcpdestportIP / ipttl / iptos / iptype). | Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X620, X440-G2, X870 | 256 |
| ExtremeSwitching X690, X590 | 512 | |
| ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique Layer 2 permit/deny traffic classification rules (ethertype/port). | Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870 | 184 |
| ExtremeSwitching X620, X440-G2 | 184 | |
| ExtremeSwitching X690, X590 | 440 | |
| Policy-based routing (PBR) redundancy—maximum number of flow-redirects. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
256 o |
| Policy-based routing (PBR) redundancy—maximum number of next hops per each flow-direct. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
32o |
| Private VLANs—maximum number of subscribers. Assumes a minimum of one port per network and subscriber VLAN. | Summit X770 | 103 |
| Summit X670-G2 | 63 | |
| Summit X460-G2 | 53 | |
| Summit X450-G2 | 51 | |
| ExtremeSwitching X440-G2 | 47 | |
| ExtremeSwitching X620 | 15 | |
| ExtremeSwitching X870 | 127 | |
| ExtremeSwitching X690 | 71 | |
| ExtremeSwitching X590 | 31 | |
| Private
VLANs—maximum number of private VLANs with an IP address on the network VLAN.
Note: This limit is dependent on the maximum number of private
VLANs in an L2-only environment if the configuration has tagged and translated ports.
|
Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 1,024 |
| Summit X450-G2 | 510 | |
| ExtremeSwitching X440-G2 | 255 | |
| ExtremeSwitching X620 | 510 | |
| Private VLANs—maximum number of private VLANs in an L2-only environment. | Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 1,280 |
| Summit X450-G2 | 597 | |
| ExtremeSwitching X440-G2, X620 | 255 | |
| PTP/1588v2 Clock Ports | Summit X770, X460-G2, X670-G2 | 32 for boundary clock 1 for ordinary clock |
| ExtremeSwitching X440-G2, X620, X870, X690, X590 | N/A | |
| PTP/1588v2 Clock Instances | Summit X770, X670-G2, X460-G2 | 2 combinations:
|
| ExtremeSwitching X440-G2, X620, X870, X690, X590 | N/A | |
| PTP/1588v2 Unicast Static Slaves | Summit X770, X670-G2, X460-G2 | 40 entries per clock port |
| ExtremeSwitching X440-G2, X620, X870, X690, X590 | N/A | |
| PTP/1588v2 Unicast Static Masters | Summit X770, X670-G2, X460-G2 | 10 entries per clock type |
| ExtremeSwitching X440-G2, X620, X870, X690, X590 | N/A | |
| Route policies—suggested maximum number of lines in a route policy file. |
Summit X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
10,000 |
| RIP Learned Routes—maximum number of RIP routes supported without aggregation. |
Summit X770, X670-G2, X460-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 |
10,000 |
| RIP interfaces on a single router—recommended maximum number of RIP routed interfaces on a switch. | Summit X670-G2, X460-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 | 256 |
| ExtremeSwitching X440-G2, X620 | 128 | |
| RIPng learned routes—maximum number of RIPng routes. | Summit X670-G2, X460-G2, X770, X450-G2, X870, X690, X590 | 3,000 |
| ExtremeSwitching X440-G2, X620 | N/A | |
| Spanning Tree
(maximum STPDs)—maximum number of Spanning Tree Domains on port mode
EMISTP. Note: STP limits are the same for all license levels.
|
Summit X450-G2, X770, X670-G2, X460-G2, and ExtremeSwitching X620, X870, X690, X590 | 64 |
| ExtremeSwitching X440-G2 | 32 | |
| Spanning Tree
PVST+—maximum number of port mode PVST domains. Note: For all platforms, the maximum number of active ports per PVST
domain depends on the maximum number of spanning tree ports supported on given platform. For
example, ExtremeSwitching X670-G2 supports 256 PVST domains (maximum), and 4,096 STP ports
(maximum), so the maximum number of active ports per PVST domain would be 16 ports (4,096 ÷
256).
|
Summit X770, X670-G2, and ExtremeSwitching X620 | 256 |
| Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2 | 128 | |
| ExtremeSwitching X870, X690, X590 | 384 | |
| Spanning Tree—maximum number of multiple spanning tree instances (MSTI) domains. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X870, X690, X590 | 64 |
| ExtremeSwitching X440-G2 | 32 | |
| Spanning
Tree—maximum number of VLANs per MSTI. Note: Maximum number of 10 active ports per VLAN when all
500 VLANs are in one MSTI.
|
Summit X770, X670-G2 | 500 |
| Summit X460-G2, X450-G2, ExtremeSwitching X620, X870, X690, X590 | 600 | |
| ExtremeSwitching X440-G2 | 256 | |
| Spanning Tree—maximum number of VLANs on all MSTP instances. | Summit X770, X670-G2, X460-G2, X450-G2, ExtremeSwitching X620, X870, X690, X590 | 1,024 |
| ExtremeSwitching X440-G2 | 512 | |
| Spanning Tree (802.1d domains)—maximum number of 802.1d domains per port. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
1 |
| Spanning Tree (number of ports)—maximum number of ports including all Spanning Tree domains. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X870, X690, X590 | 4,096 |
| ExtremeSwitching X440-G2 | 2,048 | |
| Spanning Tree (maximum VLANs)—maximum number of STP-protected VLANs (dot1d and dot1w). | Summit X770, X670-G2, X460-G2, X450-G2, and ExtremeSwitching X620, X870, X690, X590 | 1,024 |
| ExtremeSwitching X440-G2 | 600 | |
| SSH (number of sessions)—maximum number of simultaneous SSH sessions. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 8 |
| Static MAC multicast FDB entries—maximum number of permanent multicast MAC entries configured into the FDB. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 1,024 |
| Syslog servers—maximum number of simultaneous Syslog servers that are supported. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 16 |
| Syslog targets—maximum number of configurable Syslog targets. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 16 |
| Telnet (number of sessions)—maximum number of simultaneous Telnet sessions. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 8 |
| Virtual routers—maximum number of user-created virtual routers that can be created on a switch. | Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 | 63 |
| ExtremeSwitching X440-G2, X620 | 16 (local-only VRs) | |
| Virtual router
forwarding (VRFs)—maximum number of VRFs that can be created on a switch.
Note: * Subject to other system limitations.
|
Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 | 960 * |
| ExtremeSwitching X440-G2, X620 | 16 (local-only VRFs) | |
| Virtual router protocols per VR—maximum number of routing protocols per VR. | Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 | 8 |
| ExtremeSwitching X440-G2, X620 | N/A | |
| Virtual router protocols per switch—maximum number of VR protocols per switch. | Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 | 64 |
| ExtremeSwitching X440-G2, X620 | N/A | |
| VLAN aggregation—maximum number of port-VLAN combinations on any one superVLAN and all of its subVLANs. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 1,000 |
| VLANs—includes all VLANs.
Note: ExtremeXOS supports only 4,092 user-configurable VLANs.
(VLAN 1 is the default VLAN, and 4,095 is the management VLAN, and you may not configure
them.)
|
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 4,094 |
| VLANs (Layer 2)—maximum number of Layer 2 VLANs. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 4,094 |
| VLANs (Layer 3)—maximum number of VLANs performing IPv4 and/or IPv6 routing. Excludes sub-VLANs. | Summit X460-G2, X770, X670-G2, X450-G2, ExtremeSwitching X870, X690, X590 | 2,048 |
| ExtremeSwitching X440-G2, X620 | 510 | |
| VLANs (maximum active port-based)—maximum active ports per VLAN when 4,094 VLANs are configured with default license. | Summit X670-G2, ExtremeSwitching X870, X690, X590 | 32 |
| ExtremeSwitching X440-G2 | 28 | |
| Summit X460-G2, X770 | 26 | |
| ExtremeSwitching X620 | 16 | |
| Summit X450-G2 | 29 | |
| Summit X460-G2 | 24 | |
| VLANs (maximum active protocol-sensitive filters)—number of simultaneously active protocol filters in the switch. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2. X870, X690, X590 |
16 |
| VLAN translation—maximum number of translation VLANs. Assumes a minimum of one port per translation and member VLAN. | Summit X770 | 103 |
| Summit X670-G2 | 63 | |
| Summit X460-G2 | 53 | |
| Summit X450-G2 | 51 | |
| ExtremeSwitching X620 | 15 | |
| ExtremeSwitching X440-G2 | 47 | |
| ExtremeSwitching X870 | 127 | |
| ExtremeSwitching X690 | 71 | |
| ExtremeSwitching X590 | 31 | |
| VLAN
translation—maximum number of translation VLAN pairs with an IP address on the
translation VLAN. Note: This limit is dependent on the maximum number of
translation VLAN pairs in an L2-only environment if the configuration includes tagged and
translated ports.
|
Summit X770, X670-G2, ExtremeSwitching X870, X690, X590 | 1,024 |
| Summit X450-G2 | 512 | |
| ExtremeSwitching X620 | 510 | |
| ExtremeSwitching X440-G2 | 255 | |
| VLAN translation—maximum number of translation VLAN pairs in an L2-only environment. | Summit X450-G2, X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 2,046 |
| ExtremeSwitching X440-G2, X620 | 255 | |
| XML requests—maximum
number of XML requests per second. Note: Limits are dependent on load and type of XML request. These
values are dynamic ACL data requests.
|
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 10 with 100 DACLs |
| XNV authentication—maximum number of VMs that can be processed (combination of local and network VMs). | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 2,048 |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | 1,024 | |
| XNV database entries—maximum number of VM database entries (combination of local and network VMs). | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 16,000 |
| XNV database entries—maximum number of VPP database entries (combination of local and network VPPs). | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 2,048 |
| XNV dynamic VLAN—Maximum number of dynamic VLANs created (from VPPs /local VMs). | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 2,048 |
| XNV local VPPs—maximum number of XNV local VPPs. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
2,048 ingress 512 egress |
| XNV policies/dynamic ACLs—maximum number of policies/dynamic ACLs that can be configured per VPP. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
8 ingress 4 egress |
| XNV network VPPs—maximum number of XNV network VPPs.p | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
2,048 ingress 512 egress |
The following table shows supported limits for features in the Advanced Edge License.
| Metric | Product | Limit |
|---|---|---|
| BGP auto-peering—maximum number of auto-peering nodes and VTEPs. | Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 | 64 |
| BGP auto-peering attached IPv4 hosts— maximum number of attached IPv4 hosts. | Summit X670-G2, X770 | 16,000 |
| ExtremeSwitching X870, X690, X590 | 64,000 | |
| BGP auto-peering attached IPv6 hosts— maximum number of attached IPv6 hosts. | Summit X670-G2, X770 | 254 |
| ExtremeSwitching X870, X690, X590 | 8,000 | |
| BGP auto-peering
ECMP—maximum number equal cost multipath for auto-peering. Note: * Subject to the limitation imposed by the number of
physical ports on a switch.
|
Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 | 16* |
| BGP auto-peering maximum IPv4 prefixes with ECMP—Maximum number of IPv4 Network prefixes with ECMP. | Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 | 64,000 |
| BGP auto-peering maximum IPv6 prefixes with ECMP—Maximum number of IPv6 Network prefixes with ECMP. | Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 | 8,000 |
| BGP auto-peering MLAG peers—maximum MLAG peers per AutoBGP node. | Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 | 1 |
| BGP auto-peering VRFs—maximum number of VRFs. | Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 | 64 |
| BGP auto-peering EVPN instances—maximum EVPN instances. | Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 | 4,096 |
| BGP auto-peering asymmetrical routing tenant VLANs—maximum number of tenant VLANs supporting asymmetric routing. | Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 | 1,024 |
| EAPS
domains—maximum number of EAPS domains. Note: An EAPS ring that is being spatially reused cannot have
more than four configured EAPS domains.
|
ExtremeSwitching X870, X690, X590 | 128 |
| Summit X670-G2, X450-G2, X460-G2, X770 | 64 | |
| ExtremeSwitching X440-G2, X620 | 32 | |
| EAPSv2 protected VLANs—maximum number of protected VLANs. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X440-G2, X620 | 500 |
| ExtremeSwitching X870, X690, X590 | 2,000 | |
| ERPS domains—maximum number of ERPS domains without CFM configured. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 32 |
| ERPS domains—maximum number of ERPS domains with CFM configured. | Summit X450-G2, X670-G2, X770, and ExtremeSwitching X620, X870, X690, X590 | 16 |
| Summit X460-G2 | 32 | |
| ERPSv1 protected VLANs—maximum number of protected VLANs. | Summit X450-G2, X460-G2, X670-G2, and ExtremeSwitching X870, X690, X590 | 2,000 |
| Summit X770, ExtremeSwitching X620, X440-G2 | 1,000 | |
| ERPSv2 protected VLANs—maximum number of protected VLANs. | Summit X450-G2, X460-G2, X670-G2, and ExtremeSwitching X870, X690, X590 | 2,000 |
| Summit X770, ExtremeSwitching X620, X440-G2 | 500 | |
| ESRP groups—maximum number of ESRP groups | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 32 |
| ESRP domains—maximum number of ESRP domains. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 64 |
| ESRP L2 VLANs—maximum number of ESRP VLANs without an IP address configured. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 1,000 |
| ESRP L3 VLANs—maximum number of ESRP VLANs with an IP address configured. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 511 |
| ESRP (maximum ping tracks)—maximum number of ping tracks per VLAN. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 8 |
| ESRP (IP route tracks)—maximum IP route tracks per VLAN. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 8 |
| ESRP (VLAN tracks)—maximum number of VLAN tracks per VLAN. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 1 |
| OSPFv2/v3 ECMP—maximum number of equal cost multipath OSPFv2 and OSPFv3. | Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 | 64 |
| ExtremeSwitching X620 | 4 | |
| ExtremeSwitching X440-G2 | N/A | |
| OSPFv2 areas—as an ABR, how many OSPF areas are supported within the same switch. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 8 |
| Summit X450-G2, ExtremeSwitching X440-G2, X620 | 4 | |
| OSPFv2 external routes—recommended maximum number of external routes contained in an OSPF LSDB. | ExtremeSwitching X870, X690, X590 | 10,000 |
| Summit X770, X670-G2, X460-G2 | 5,000 | |
| Summit X450-G2, ExtremeSwitching X440-G2, X620 | 2,400 | |
| OSPFv2 inter- or intra-area routes—recommended maximum number of inter- or intra-area routes contained in an OSPF LSDB with one ABR in OSPF domain. | ExtremeSwitching X870, X690, X590 | 4,000 |
| Summit X670-G2, X460-G2, X770 | 2,000 | |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | 1,000 | |
| OSPFv2 interfaces—recommended maximum number of OSPF interfaces on a switch (active interfaces only). | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 4 |
| OSPFv2 links—maximum number of links in the router LSA. | Summit X460-G2, X670-G2, ExtremeSwitching X870, X690, X590 | 400 |
| Summit X450-G2, and ExtremeSwitching X620, X440-G2 | 4 | |
| Summit X770 | 419 | |
| OSPFv2 neighbors—maximum number of supported OSPF adjacencies. | Summit X450-G2, X770, X670-G2, X460-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 | 4 |
| OSPFv2 routers in a single area—recommended maximum number of routers in a single OSPF area. | ExtremeSwitching X870, X690, X590 | 100 |
| Summit X770, X670-G2, X460-G2 | 50 | |
| Summit X450-G2, ExtremeSwitching X440-G2, X620 | 4 | |
| OSPFv2 virtual links—maximum number of supported OSPF virtual links. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 32 |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | 4 | |
| OSPFv3 areas—as an ABR, the maximum number of supported OSPFv3 areas. | ExtremeSwitching X870, X690, X590 | 100 |
| Summit X460-G2, X670-G2, X770 | 16 | |
| Summit X450-G2, ExtremeSwitching X440-G2, X620 | 4 | |
| OSPFv3 external routes—recommended maximum number of external routes. | Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 10,000 |
| Summit X450-G2, ExtremeSwitching X440-G2, X620 | 1,200 | |
| OSPFv3 inter- or intra-area routes—recommended maximum number of inter- or intra-area routes. | ExtremeSwitching X870, X690, X590 | 4.000 |
| Summit X770, X670-G2, X460-G2 | 3,000 | |
| Summit X450-G2, ExtremeSwitching X440-G2, X620 | 500 | |
| OSPFv3 interfaces—maximum number of OSPFv3 interfaces. | Summit X770, X670-G2, X460-G2, X450-G2, ExtremeSwitching X870, X690, X440-G2, X620, X590 | 4 |
| OSPFv3 neighbors—maximum number of OSPFv3 neighbors. | Summit X450-G2, X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X440-G2, X620, X590 | 4 |
| OSPFv3 virtual links—maximum number of OSPFv3 virtual links supported. | Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 16 |
| Summit X450-G2, ExtremeSwitching X440-G2, X620 | 4 | |
| OVSDB Manager Connections—Maximum number of connections to managers that can be configured (either of TCP, PTCP, SSL, or PSSL). | Summit X770, X670-G2, ExtremeSwitching X870, X690, X590 | 8 |
| Smmit X450-G2 | N/A | |
| OVSDB Managed Switches—Maximum number of OVSDB-managed switches. | Summit X770, X670-G2, ExtremeSwitching X870, X690, X590 | 1 |
| Smmit X450-G2 | N/A | |
| PIM IPv4 (maximum interfaces)—maximum number of PIM active interfaces. | Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X440-G2, X620, X690, X590 | 4 |
| PIM IPv4 Limits—maximum number of multicast groups per dynamic rendezvous point. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
180 |
| PIM IPv4 Limits—maximum number of multicast groups per static rendezvous point. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
3,000 (depends on policy file limits) |
| PIM IPv4 Limits—maximum number of multicast sources per group. | Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 | 5,000 |
| ExtremeSwitching X440-G2, X620 | 1,500 | |
| PIM IPv4 Limits—maximum number of dynamic rendezvous points per multicast group. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
145 |
| PIM IPv4 Limits—static rendezvous points. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
32 |
| PIM IPv6 (maximum interfaces)—maximum number of PIM active interfaces. | Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X440-G2, X620, X690, X590 | 4 |
| PIM IPv6 Limits—maximum number of multicast sources per group. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 1,750 |
| Summit X450-G2 | 1,500 | |
| ExtremeSwitching X440-G2, X620 | 550 | |
| PIM IPv6 Limits—maximum number of multicast groups per dynamic rendezvous point. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
70 |
| PIM IPv6 Limits—maximum number of multicast groups per static rendezvous point. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
3,000 (depends on policy file limits) |
| PIM IPv6 Limits—maximum number of dynamic rendezvous points per multicast group. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
64 |
| PIM IPv6 Limits—maximum number of secondary address per interface. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
70 |
| PIM IPv6 Limits—static rendezvous points. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
32 |
| Port-specific VLAN tags—maximum number of port-specific VLAN tags. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 1,023 |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| Port-specific VLAN tags—maximum number of port-specific VLAN tag ports. | Summit X770, X670-G2 | 4,000 |
| Summit X460-G2, ExtremeSwitching X870, X690, X590 | 4,000 | |
| Summit X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| VRRP
(v2/v3-IPv4) (maximum instances)—maximum number of VRRP instances for a single
switch, with Advanced Edge license or higher. Note: These limits are applicable for Fabric Routing
configuration also.
Note: Number of groups configured should not
exceed the number of individual VRs supported (that is, in normal mode) for that platform
type.
|
Normal Mode (as individual VRs): |
|
| Summit X770, X670-G2, X460-G2, X450-G2, and ExtremeSwitching X870, X690, X590 | 511 | |
| ExtremeSwitching X440-G2, X620 | 128 | |
|
Scaled Mode (with groups): |
||
| Summit X770, X670-G2, X460-G2, X450-G2, and ExtremeSwitching X870, X690, X590 |
2,048 |
|
| ExtremeSwitching X440-G2, X620 | 128 | |
| VRRP (v3-IPv6)
(maximum instances)—maximum number of VRRP instances for a single switch, with
Advanced Edge license or higher. (VRRP-VRRPv3-IPv6) Note: These limits are applicable for Fabric Routing
configuration also.
Note: Number of groups configured should not
exceed the number of individual VRs supported (that is, in normal mode) for that platform
type.
|
Normal Mode (as individual VRs): |
|
| Summit X770, X670-G2, X460-G2, X450-G2, and ExtremeSwitching X870, X690, X590 | 511 | |
| ExtremeSwitching X440-G2, X620 | 128 | |
|
Scaled Mode (with groups): |
||
| Summit X770, X670-G2, X460-G2, X450-G2, and ExtremeSwitching X870, X690, X590 |
2,048 |
|
| ExtremeSwitching X440-G2, X620 | 128 | |
| VRRP (v2/v3-IPv4/IPv6) (maximum VRID)—maximum number of unique VRID numbers per switch. |
Summit X770, X670-G2, X460-G2, X450-G2 and ExtremeSwitching X440-G2, X620, X870, X690, X590 Note: With Advanced Edge license or higher.
|
255 |
| VRRP (v2/v3-IPv4/IPv6) (maximum VRIDs per VLAN)—maximum number of VRIDs per VLAN. |
Summit X770, X670-G2, X460-G2, X450-G2 and ExtremeSwitching X440-G2, X620, X870, X690, X590 Note: With Advanced Edge license or higher.
|
255 |
| VRRP (v2/v3-IPv4/IPv6) (maximum ping tracks)—maximum number of ping tracks per VLAN. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 Note: With Advanced Edge license or higher.
|
8 |
| VRRP (maximum ping tracks)—maximum number of ping tracks per VRRP Instance under 128 VRRP instances, with Advanced Edge license or higher. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
8 (20 centisecond or 1 second hello interval) |
| VRRP (v3-IPv6) (maximum ping tracks)—maximum number of ping tracks per VRRP Instance under 128 VRRP instances, with Advanced Edge license or higher. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
8 (20 centisecond or 1 second hello interval) |
| VRRP (v2/v3-IPv4/IPv6) (maximum iproute tracks)—maximum number of IP route tracks per VLAN. |
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 |
8 |
| VRRP (v2/v3-IPv4/IPv6)—maximum number of VLAN tracks per VLAN. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 | 8 |
| VXLAN—maximum virtual networks. Note: Every VPLS instance/PSTag VLAN reduces this limit by
1.
Note: Assumption is all BUM
(broadcast/unknown-unicast/multicast) FDB entries are pointing to the same set of RTEPs when
all VNETs use explicit flooding. Depends on whether all VNETs use standard or explicit and the
number of tenant VLAN ports.
|
Summit X670-G2, X770, and ExtremeSwiching X870, X690, X590 | 2,048–4,000 |
| Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| VXLAN—maximum tenant VLANs plus port combinations Note: Every (VPLS/PSTag VLAN) + port reduces the limit by
1.
|
Summit X670-G2, X770, and ExtremeSwiching X870, X690, X590 | 4,096 |
| Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| VXLAN—maximum static MAC to IP bindings. Note: Every FDB entry configured reduces this limit by 1.
|
Summit X670-G2, X770, and ExtremeSwiching X870, X690, X590 | 64,000 |
| Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| VXLAN—maximum RTEP IP addresses | Summit X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 512 |
| Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2, X620 | N/A | |
| VXLAN—maximum virtual networks with dynamic learning and OSPF extensions for VXLAN | Summit X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 4,000 |
| Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2, X620 | N/A |
The following table shows supported limits for features in the Core License.
| Metric | Product | Limit |
|---|---|---|
| BGP (aggregates)—maximum number of BGP aggregates. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 256 |
| Summit X450-G2 | 204 | |
| BGP (networks)—maximum number of BGP networks. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 1,024 |
| Summit X450-G2 | 820 | |
| BGP
(peers)—maximum number of BGP peers. Note: With default keepalive and hold timers.
|
Summit X460-G2, X670-G2, X770, ExtremeSwitching X870 | 128 |
| ExtremeSwitching X690, X590 | 300 | |
| Summit X450-G2 | 100 | |
| BGP (peer groups)—maximum number of BGP peer groups. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 64 |
| Summit X450-G2 | 50 | |
| BGP (policy entries)—maximum number of BGP policy entries per route policy. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 256 |
| Summit X450-G2 | 204 | |
| BGP (policy statements)—maximum number of BGP policy statements per route policy. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 1,024 |
| Summit X450-G2 | 820 | |
| BGP multicast address-family routes—maximum number of multicast address-family routes. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 25,000 |
| Summit X450-G2 | 20,000 | |
| BGP (unicast address-family routes)—maximum number of unicast address-family routes. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 (at default) | 25,000 |
| ExtremeSwitching X870, X690, X590 (with ALPM enabled) | 100,000 | |
| Summit X450-G2 | 20,000 | |
| BGP (non-unique routes)—maximum number of non-unique BGP routes. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 25,000 |
| Summit X450-G2 | 20,000 | |
| BGP ECMP—maximum number of equal cost multipath for BGP and BGPv6. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 2, 4, 8, 16, 32, or 64 |
| Summit X450-G2 | 64 | |
| BGPv6 (unicast address-family routes)—maximum number of unicast address family routes. | Summit X460-G2 | 6,000 |
| Summit X670-G2, X770 | 8,000 | |
| ExtremeSwitching X870, X690, X590 | 10,000 | |
| ExtremeSwitching X870, X690 (with ALPM enabled) | 100,000 | |
| Summit X450-G2 | 4,800 | |
| BGPv6 (non-unique routes)—maximum number of non-unique BGP routes. | Summit X460-G2 | 18,000 |
| Summit X670-G2, X770, ExtremeSwitching X870, X690, X590 | 24,000 | |
| Summit X450-G2 | 14,000 | |
| GRE Tunnels—maximum number of GRE tunnels. | Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X870, X690, X590 | 255 |
| ExtremeSwitching X620, X440G2 | N/A | |
| IS-IS adjacencies—maximum number of supported IS-IS adjacencies. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 128 |
| Summit X450-G2 | N/A | |
| IS-IS ECMP—maximum number of equal cost multipath for IS-IS. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 2, 4, or 8 |
| Summit X450-G2 | N/A | |
| IS-IS interfaces—maximum number of interfaces that can support IS-IS. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 255 |
| Summit X450-G2 | N/A | |
| IS-IS routers in an area—recommended maximum number of IS-IS routers in an area. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 256 |
| Summit X450-G2 | N/A | |
| IS-IS route origination—recommended maximum number of routes that can be originated by an IS-IS node. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 20,000 |
| Summit X450-G2 | N/A | |
| IS-IS IPv4 L1 routes in an L1 router—recommended maximum number of IS-IS Level 1 routes in a Level 1 IS-IS router. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 25,000 |
| Summit X450-G2 | N/A | |
| IS-IS IPv4 L2 routes—recommended maximum number of IS-IS Level 2 routes. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 25,000 |
| Summit X450-G2 | N/A | |
| IS-IS IPv4 L1 routes in an L1/L2 router—recommended maximum number of IS-IS Level 1 routes in an L1/L2 IS-IS router. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 20,000 |
| Summit X450-G2 | N/A | |
| IS-IS IPv6 L1 routes in an L1 router—recommended maximum number of IS-IS Level 1 routes in a Level 1 IS-IS router. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 10,000 |
| Summit X450-G2 | N/A | |
| IS-IS IPv6 L2 routes—recommended maximum number of IS-IS Level 2 routes. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 10,000 |
| Summit X450-G2 | N/A | |
| IS-IS IPv6 L1 routes in an L1/L2 router—recommended maximum number of IS-IS Level 1 routes in a L1/l2 router. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 10,000 |
| Summit X450-G2 | N/A | |
| IS-IS IPv4/IPv6 L1 routes in an L1 router—recommended maximum number of IS-IS Level 1 routes in a Level 1 IS-IS router. The numbers documented are based on 50% IPv4 routes and 50% IPv6 routes. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 20,000 |
| Summit X450-G2 | N/A | |
| IS-IS IPv4/IPv6 L2 routes in an L2 router—recommended maximum number of IS-IS Level 2 routes in a Level 2 IS-IS router. The numbers documented are based on 50% IPv4 routes and 50% IPv6 routes. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 20,000 |
| Summit X450-G2 | N/A | |
| IS-IS IPv4/IPv6 L1 routes in an L1/L2 router—recommended maximum number of IS-IS Level 1 routes in a Level 1/Level2 IS-IS router. The numbers documented are based on 50% IPv4 routes and 50% IPv6 routes. | Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 20,000 |
| Summit X450-G2 | N/A | |
| MSDP active peers—maximum number of active MSDP peers. | Summit X450-G2, X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 64 |
| MSDP SA cache entries—maximum number of entries in SA cache. | Summit X670-G2, X770, ExtremeSwitching X690, X590 | 14,000 |
| Summit X460-G2 | 10,000 | |
| ExtremeSwitching X870 | 11,000 | |
| Summit X450-G2 | 8,000 | |
| MSDP maximum mesh groups—maximum number of MSDP mesh groups. | Summit X450-G2, X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 16 |
| OSPFv2/v3 ECMP—maximum number of equal cost multipath OSPFv2 and OSPFv3. | Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 | 64 |
| OSPFv2 areas—as an ABR, how many OSPF areas are supported within the same switch. | Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 8 |
| OSPFv2 external routes—recommended maximum number of external routes contained in an OSPF LSDB. | ExtremeSwitching X870, X690, X590 | 10,000 |
| Summit X770, X670-G2, X460-G2 | 5,000 | |
| Summit X450-G2 | 4,000 | |
| OSPFv2 inter- or intra-area routes—recommended maximum number of inter- or intra-area routes contained in an OSPF LSDB with one ABR in OSPF domain. | ExtremeSwitching X870, X690, X590 | 4,000 |
| Summit X670-G2, X460-G2, X770 | 2,000 | |
| Summit X450-G2 | 1,600 | |
| OSPFv2 interfaces—recommended maximum number of OSPF interfaces on a switch (active interfaces only). | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 400 |
| Summit X450-G2 | 320 | |
| OSPFv2 links—maximum number of links in the router LSA. | Summit X460-G2, X670-G2, ExtremeSwitching X870, X690, X590 | 400 |
| Summit X770 | 419 | |
| Summit X450-G2 | 320 | |
| OSPFv2 neighbors—maximum number of supported OSPF adjacencies. | Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 128 |
| Summit X450-G2 | 96 | |
| OSPFv2 routers in a single area—recommended maximum number of routers in a single OSPF area. | ExtremeSwitching X870, X690, X590 | 100 |
| Summit X770, X670-G2, X460-G2 | 50 | |
| Summit X450-G2 | 40 | |
| OSPFv2 virtual links—maximum number of supported OSPF virtual links. | Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 | 32 |
| Summit X450-G2 | 25 | |
| OSPFv3 areas—as an ABR, the maximum number of supported OSPFv3 areas. | ExtremeSwitching X870, X690, X590 | 100 |
| Summit X460-G2, X670-G2, X770 | 16 | |
| Summit X450-G2 | 12 | |
| OSPFv3 external routes—recommended maximum number of external routes. | Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 10,000 |
| Summit X450-G2 | 7,500 | |
| OSPFv3 inter- or intra-area routes—recommended maximum number of inter- or intra-area routes. | ExtremeSwitching X870, X690, X590 | 4.000 |
| Summit X770, X670-G2, X460-G2 | 3,000 | |
| Summit X450-G2 | 500 | |
| OSPFv3 interfaces—maximum number of OSPFv3 interfaces. | Summit X770 | 128 |
| Summit X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 256 | |
| Summit X450-G2 | 192 | |
| OSPFv3 neighbors—maximum number of OSPFv3 neighbors. | Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 64 |
| Summit X450-G2 | 48 | |
| OSPFv3 virtual links—maximum number of OSPFv3 virtual links supported. | Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 | 16 |
| Summit X450-G2 | 12 | |
| PIM IPv4 (maximum interfaces)—maximum number of PIM active interfaces. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 256 |
| PIM IPv4 Limits—maximum number of multicast groups per dynamic rendezvous point. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 180 |
| PIM IPv4 Limits—maximum number of multicast groups per static rendezvous point. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 3,000 (depends on policy file limits) |
| PIM IPv4 Limits—maximum number of multicast sources per group. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 5,000 |
| PIM IPv4 Limits—maximum number of dynamic rendezvous points per multicast group. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 145 |
| PIM IPv4 Limits—static rendezvous points. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 32 |
| PIM IPv6 (maximum interfaces)—maximum number of PIM active interfaces. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 256 |
| PIM IPv6 Limits—maximum number of multicast sources per group. |
Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 |
2,500 |
| Summit X450-G2, | 1,500 | |
| PIM IPv6 Limits—maximum number of multicast groups per dynamic rendezvous point. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 |
70 |
| PIM IPv6 Limits—maximum number of multicast groups per static rendezvous point. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 |
3,000 (depends on policy file limits) |
| PIM IPv6 Limits—maximum number of dynamic rendezvous points per multicast group. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 64 |
| PIM IPv6 Limits—maximum number of secondary address per interface. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 70 |
| PIM IPv6 Limits—static rendezvous points. | Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 | 32 |