Limits

This chapter summarizes the supported limits in ExtremeXOS 22.7.5.

The limits data is grouped by license level that contains the associated features:

For more information about licenses, see ExtremeXOS 22.7 Feature License Requirements .

The following tables summarize tested metrics for a variety of features, as measured in a per-system basis unless otherwise noted. These limits may change, but represent the current status. The contents of this table supersede any values mentioned in the ExtremeXOS books.

The scaling and performance information shown in the following tables is provided for the purpose of assisting with network design. It is recommended that network architects and administrators design and manage networks with an appropriate level of network scaling “head room.” The scaling and performance figures provided have been verified using specific network topologies using limited switch configurations. There is no guarantee that the scaling and performance figures shown are applicable to all network topologies and switch configurations and are provided as a realistic estimation only. If you experience scaling and performance characteristics that you feel are sufficiently below what has been documented, contact Extreme Networks technical support for additional assistance.

The route limits shown in the following tables for IPv4 and IPv6 routing protocols are software limits only. The actual hardware limits may be higher or lower than the software limits, based on platform. The hardware limits for specific platforms are specified as "IPv4/IPv6 routes (LPM entries in hardware)" in the following tables.

In the Extended Edge Switching architecture, Layer-2, Layer-3, and multicast packet forwarding and filtering operations take place on the controlling bridge. The controlling bridge switch and attached BPEs (V400 Virtual Port Extenders) constitute a single, extended switch system. Therefore, the Extended Edge Switching system assumes the scale and limits from the specific controlling bridge model (for example, Summit X670-G2 or ExtremeSwitching X690 and X590 series switches) in use. For applicable limits, see the following tables for the controlling bridge you are using.

Supported Limits for Edge License

The following table shows supported limits for features in the Edge License.

Table 1. Supported Limits for Edge License
Metric Product Limit
AAA (local)—maximum number of admin and local user accounts. All platforms 16
Access lists (meters)—maximum number of meters. ExtremeSwitching X620, X440-G2 1,024 ingress

256 egress

Summit X770, X670-G2, X450-G2, X460-G2 1,024 ingress

512 egress

ExtremeSwitching X870, X690, X590 2,048 ingress

512 egress

Access lists (policies)—suggested maximum number of lines in a single policy file. All platforms 300,000
Access lists (policies)—maximum number of rules in a single policy file.a Summit X460-G2, X450-G2, X770, X670-G2 4,096 ingress

1,024 egress

ExtremeSwitching X620, X440-G2 2,048 ingress

512 egress

ExtremeSwitching X870 3,072 ingress

1,024 egress

ExtremeSwitching X690, X590 8,192 ingress

1,024 egress

Access lists (policies)—maximum number of rules in a single policy file in first stage (VFP). Summit X450-G2, X460-G2 2,048 ingress only
Summit X670-G2, X770, ExtremeSwitching X870, X690 1,024 ingress only

ExtremeSwitching X620, X440-G2

512 ingress only

ExtremeSwitching X590 2,048 ingress only
Access lists (slices)—number of ACL slices. Summit X460-G2, X450-G2 16 ingress

4 egress

Summit X770, X670-G2, ExtremeSwitching X690, X590 12 ingress

4 egress

ExtremeSwitching X440-G2, X620 8 ingress

4 egress

ExtremeSwitching X870 4 ingress

4 egress

Access lists (slices)—number of ACL slices in first stage (VFP). Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 4 ingress only
ACL Per Port Meters—number of meters supported per port. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 16
ACL port ranges Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 32
Meters Packets-Per-Second Capable Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 Yes
AVB (audio video bridging)—maximum number of active streams. Summit X450-G2, X460-G2, X770, and ExtremeSwitching X620, X440-G2 1,024
Summit X670-G2 4,096
ExtremeSwitching X590, X690, X870 N/A
BFD sessions (Software Mode)—maximum number of BFD sessions. Summit X460-G2, X670-G2, X450-G2, X770, ExtremeSwitching X440-G2, X620, X870, X690, X590 (default timers—1 sec) 512
Summit X460-G2, X670-G2, X450-G2, X770, ExtremeSwitching X440-G2, X620, X870, X690, X590 (minimal timers—100 msec) 10c
BFD IPv4 sessions (Hardware Assisted)—maximum number of IPv4 BFD sessions. Summit X460-G2, ExtremeSwitching X870, X690, X590 900 (PTP not enabled)

425 (PTP enabled)

256 (with 3 ms transmit interval)

BFD IPv6 sessions (Hardware Assisted)—maximum number of IPv6 BFD sessions. Summit X460-G2, ExtremeSwitching X870, X690, X590 425 (PTP not enabled)
BOOTP/DHCP relay—maximum number of BOOTP or DHCP servers per virtual router. Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 8
BOOTP/DHCP relay—maximum number of BOOTP or DHCP servers per VLAN. Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 8
BOOTP/DHCP relay—maximum number of DHCPv4/v6 relay agents Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 4,000
Connectivity fault management (CFM)—maximum number or CFM domains.
Note: With Advanced Edge license or higher.
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 8
CFM—maximum number of CFM associations.
Note: With Advanced Edge license or higher.
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 256
CFM—maximum number of CFM up end points.
Note: With Advanced Edge license or higher.
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 32
CFM—maximum number of CFM down end points.
Note: With Advanced Edge license or higher.
Summit X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 32
Summit X460-G2 256 (non-load shared ports)

32 (load shared ports)

CFM—maximum number of CFM remote end points per up/down end point.
Note: With Advanced Edge license or higher.
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 2,000
CFM—maximum number of dot1ag ports.
Note: With Advanced Edge license or higher.
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 128
CFM—maximum number of CFM segments.
Note: With Advanced Edge license or higher.
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 1,000
CFM—maximum number of MIPs.
Note: With Advanced Edge license or higher.
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X620, X440-G2, X870, X690, X590 256
CLEAR-Flow—total number of rules supported. The ACL rules plus CLEAR-Flow rules must be less than the total number of supported ACLs. Summit X460-G2, X770, X670-G2, X450-G2 4,094
ExtremeSwitching X440-G2, X620 1,024
ExtremeSwitching X870 3,072
ExtremeSwitching X690, X590 8,192
Data Center Bridging eXchange (DCBX) protocol Type Length Value (TLVs)—maximum number of DCBX application TLVs. Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 8
DHCPv6 Prefix Delegation Snooping—Maximum number of DHCPv6 prefix delegation snooped entries. Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X620, X440-G2, X870, X690, X590 256 (with Underlying Protocol Ripng)

128 (with Underlying protocol OSPFv3)

1,024 (with static routes)

DHCP snooping entries—maximum number of DHCP snooping entries. Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X620, X440-G2, X870, X690, X590 2,048
Dynamic ACLs—maximum number of ACLs processed per second.
Note: Limits are load-dependent.
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590
  • with 50 DACLs
  • with 500 DACLs
  • 10
  • 5
EAPS domains—maximum number of EAPS domains.
Note: An EAPS ring that is being spatially reused cannot have more than four configured EAPS domains.
Note: You can increase the number of domains by upgrading to the Advanced Edge license.
Summit X670-G2, X450-G2, X460-G2, X770,and ExtremeSwitching X440-G2, X620, X870, X690, X590 4
EAPSv1 protected VLANs—maximum number of protected VLANs. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2 1,000
ExtremeSwitching X870, X690, X590 2,000
ERPS domains—maximum number of ERPS domains with or without CFM configured.
Note: You can increase the number of domains by upgrading to the Advanced Edge license.
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 4
ERPSv1 protected VLANs—maximum number of protected VLANs. ExtremeSwitching X870, X690, X590 2,000
Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X620, X440-G2 1,000
ERPSv2 protected VLANs—maximum number of protected VLANs. Summit X450-G2, X460-G2, X670-G2, and ExtremeSwitching X870, X690, X590 2,000
Summit X770, ExtremeSwitching X620, X440-G2 500
ELSM (vlan-ports)—maximum number of VLAN ports.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X870, X690, X590

5,000
ExtremeSwitching X440-G2 4,000
Extended Edge Switching maximum BPEs—maximum number of attached bridge port extenders (BPEs). Summit X670-G2, ExtremeSwitching X690, X590 48
Extended Edge Switching maximum BPEs per ring—maximum number of attached bridge port extenders (BPEs) per ring. Summit X670-G2, ExtremeSwitching X690, X590 8
Extended Edge Switching maximum cascade ports—maximum number of upstream ports on bridge port extenders (BPEs). Summit X670-G2, ExtremeSwitching X690, X590

2 on V400-24 models

4 on V400-48 models

Extended Edge Switching maximum tiers—maximum number of cascade levels (tiers) of bridge port extenders (BPEs). Summit X670-G2, ExtremeSwitching X690, X590 4
Extended Edge Switching VLAN+ port memberships—maximum number of VLAN+ (extended) port memberships. Summit X670-G2, ExtremeSwitching X690, X590

12,000 in hash mode (default)

131,000 in port-group mode

Forwarding rate—maximum L3 software forwarding rate. ExtremeSwitching X690, X590 30,000 pps
ExtremeSwitching X870 32,000 pps
Summit X450-G2 16,000 pps
Summit X460-G2 17,000 pps
ExtremeSwitching X620 10,000 pps
Summit X670-G2 15,000 pps
Summit X770 6,500 pps
ExtremeSwitching X440-G2 9,000 pps
FDB (unicast blackhole entries)—maximum number of unicast blackhole FDB entries. Summit X460-G2 49,152f
Summit X770, X670-G2 294,912f
Summit X450-G2 34,816f
ExtremeSwitching X620, X440-G2 16,384f
ExtremeSwitching X870 139,264f
ExtremeSwitching X690, X590 278,528f
FDB (multicast blackhole entries)—maximum number of multicast blackhole FDB entries. Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2, X620 1,024
Summit X770, X670-G2, ExtremeSwitching X870, X690, X590 4,096
FDB (maximum L2 entries)—maximum number of MAC addresses. Summit X460-G2 98,300g
Summit X770, X670-G2 294,912g
Summit X450-G2 68,000g
ExtremeSwitching X620, X440-G2 16,384
ExtremeSwitching X870 139,264g
ExtremeSwitching X690, X590 278,528g
FDB (Maximum L2 entries)—maximum number of multicast FDB entries. Summit X770, X670-G2, ExtremeSwitching X870, X690, X590 4,096
Summit X450-G2, X460-G2, and ExtremeSwitching X620, X440-G2 1,024
Identity management—maximum number of Blacklist entries. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 512
Identity management—maximum number of Whitelist entries. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 512
Identity management—maximum number of roles that can be created. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 64
Identity management—maximum role hierarchy depth allowed. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 5
Identity management—maximum number of attribute value pairs in a role match criteria. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 16
Identity management—maximum of child roles for a role. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 8
Identity management—maximum number of policies/dynamic ACLs that can be configured per role. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 8
Identity management—maximum number of LDAP servers that can be configured. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 8
Identity management—maximum number of Kerberos servers that can be configured. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 20
Identity management—maximum database memory-size. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 512
Identity management—recommended number of identities per switch.
Note: Number of identities per switch is for a default identity management database size (512 Kbytes) across all platforms.
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 100
Identity management—recommended number of ACL entries per identity.
Note: Number of ACLs per identity, based on system ACL limitation.
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 20
Identity management—maximum number of dynamic ACL entries configured as an individual dynamic rule, or as an ACL entry in a policy file. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 500
IGMP snooping per VLAN filters—maximum number of VLANs supported in per-VLAN IGMP snooping mode. Summit X460-G2, ExtremeSwitching X870 1,500
Summit X450-G2 2,048
Summit X770, X670-G2 2,000
ExtremeSwitching X620, X440-G2 1,000
ExtremeSwitching X690, X590 4,000
IGMPv1/v2 SSM-map entries—maximum number of IGMPv1/v2 SSM mapping entries. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 500
IGMPv1/v2 SSM-map entries—maximum number of sources per group in IGMPv1/v2 SSM mapping entries. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 50
IGMPv2 subscriber—maximum number of IGMPv2 subscribers per port.n Summit X770, X670-G2, X460-G2, X450-G2 4,000
ExtremeSwitching X440-G2, X620 3,500
ExtremeSwitching X870, X690, X590 4,000
IGMPv2 subscriber—maximum number of IGMPv2 subscribers per switch.n Summit X770, X670-G2 30,000
Summit X460-G2, X450-G2 20,000
ExtremeSwitching X620, X440-G2 17,500
ExtremeSwitching X870, X690, X590 45,000
IGMPv3 maximum source per group—maximum number of source addresses per group. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 250
IGMPv3 subscriber—maximum number of IGMPv3 subscribers per port.n Summit X770, X670-G2, X460-G2, X450-G2 4,000
ExtremeSwitching X440-G2, X620 3,500
ExtremeSwitching X870, X690, X590 4,000
IGMPv3 subscriber—maximum number of IGMPv3 subscribers per switch.n Summit X460-G2, X450-G2 20,000
Summit X770, X670-G2 30,000
ExtremeSwitching X620, X440-G2 17,500
ExtremeSwitching X870, X690, X590 45,000
IP ARP entries in software—maximum number of IP ARP entries in software.
Note: Might be limited by hardware capacity of FDB (maximum L2 entries).
Summit X670-G2, X770 131,072 (up to)h
Summit X460-G2 57,344 (up to)h
Summit X450-G2 47,000 (up to)h
ExtremeSwitching X440-G2, X620 20,480
ExtremeSwitching X870 94,206 (up to)h
ExtremeSwitching X690, X590 157,694 (up to) h
IPv4 ARP entries in hardware with minimum LPM routes—maximum recommended number of IPv4 ARP entries in hardware, with minimum LPM routes present. Assumes number of IP route reserved entries is 100 or less. ExtremeSwitching X870 74,000 (up to)h
Summit X460-G2 50,000 (up to)h
Summit X770, X670-G2 108,000 (up to)h
Summit X450-G2 39,000 (up to)h
ExtremeSwitching X620 1,500
ExtremeSwitching X440-G2 1,000
ExtremeSwitching X690, X590 119,000 (up to) h
IPv4 ARP entries in hardware with maximum LPM routes—maximum recommended number of IPv4 ARP entries in hardware, with maximum LPM routes present. Assumes number of IP route reserved entries is “maximum.” ExtremeSwitching X870 64,000 (up to)h
Summit X460-G2 43,000 (up to)h
Summit X770, X670-G2 98,000 (up to)h
Summit X450-G2 29,000 (up to)h
ExtremeSwitching X620 1,500
ExtremeSwitching X440-G2 1,000
ExtremeSwitching X690, X590 109,000 (up to) h
IP flow information export (IPFIX)—number of simultaneous flows. Summit X460-G2 2,048 ingress

2,048 egress

Summit X450-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 N/A
IPv4 remote hosts in hardware with zero LPM routes—maximum recommended number of IPv4 remote hosts (hosts reachable through a gateway) in hardware when LPM routing is not used. Assumes number of IP route reserved entries is 0, and number of IPv4 ARP entries present is 100 or less. ExtremeSwitching X870 120,000 (up to)h
Summit X460-G2 73,000h
Summit X770, X670-G2 176,000 (up to)h
Summit X450-G2 61,000 (up to)h
ExtremeSwitching X440-G2, X620 3,500
ExtremeSwitching X690, X590 216,000 (up to) h
IPv4 routes—maximum number of IPv4 routes in software (combination of unicast and multicast routes), including static and from all routing protocols. Summit X460-G2, X450-G2, X440-G2, X620 25,000
Summit X670-G2, ExtremeSwitching X690, X870, X590 131,000
Summit X770 100,000
IPv4 routes (LPM entries in hardware)— number of IPv4 routes in hardware. Summit X460-G2 12,000
Summit X450-G2 16,000
Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 131,000 q
ExtremeSwitching X620, X440-G2 480
IPv6 6in4 tunnel—maximum number of IPv6 6in4 tunnels. Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 255
ExtremeSwitching X440-G2, X620 N/A
IPv6 6to4 tunnel—maximum number of IPv6 6to4 tunnels. Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 1 (per virtual router)
ExtremeSwitching X440-G2, X620 N/A
IPv6 addresses on an interface—maximum number of IPv6 addresses on an interface. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 255
IPv6 addresses on a switch—maximum number of IPv6 addresses on a switch. Summit X770, X670-G2, X460-G2, X450-G2, ExtremeSwitching X870, X690, X590 2,048
ExtremeSwitching X620, X440-G2 510
IPv6 host entries in hardware—maximum number of IPv6 neighbor entries in hardware. Summit X770, X670-G2 36,750 h
Summit X460-G2 22,000h
Summit X450-G2 12,000h
ExtremeSwitching X440-G2 1,000
ExtremeSwitching X620 1,500
ExtremeSwitching X690, X590 24,500h
ExtremeSwitching X870 22,000h
IPv6 routes in software—maximum number of IPv6 routes in software, including static routes and routes from all routing protocols. Summit X450-G2, X460-G2, and ExtremeSwitching X620, X440-G2 25,000
Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 65,000 q
IPv6 routes (LPM entries in hardware)—maximum number of IPv6 routes in hardware. Summit X460-G2 6,000
Summit X450-G2 8,000
Summit X670-G2, X770, ExtremeSwitching X690, X870, X590

65,000q

ExtremeSwitching X620, X440-G2, 240
IPv6 routes with a mask greater than 64 bits in hardware—maximum number of such IPv6 LPM routes in hardware. Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 8,192 r
ExtremeSwitching X440-G2, X620 1,024
Summit X450-G2, X460-G2 2,048
IPv6 route sharing in hardware—route mask lengths for which ECMP is supported in hardware. Summit X460-G2, X450-G2, and ExtremeSwitching X620

0–64

>64 single path only

Summit X670-G2, X770, and ExtremeSwitching X690, X870, X590 0–128r
ExtremeSwitching X440-G2 Not supported
IP router interfaces—maximum number of VLANs performing IPv4 and/or IPv6 routing. Excludes sub-VLANs. Summit X460-G2, X770, X670-G2, X450-G2, ExtremeSwitching X870, X690, X590 2,048
ExtremeSwitching X620, X440-G2 510
IP multicast static routes—maximum number of permanent multicast IP routes. Summit X460-G2, X670-G2, X450-G2, X770, ExtremeSwitching X870, X690, X590 1,024
IP unicast static routes—maximum number of permanent IP unicast routes. Summit X460-G2, X670-G2, X450-G2, X770, ExtremeSwitching X870, X690, X590 1,024
ExtremeSwitching X620, X440-G2 480
IP route sharing (maximum gateways)—Configurable maximum number of gateways used by equal cost multipath OSPF, BGP, IS-IS, static routes, or L2VPNs. Static routes, OSPF, and BGP are limited to 64 ECMP gateways per destination, while IS-IS is limited to 8. L2VPNs are limited to 16 LSPs per pseudowire on platforms that support 32 gateways, and 64 LSPs per pseudowire on platforms that support 64 gateways. Summit X460-G2, X670-G2, X450-G2, X770, and ExtremeSwitching X620, X870, X690, X590 2, 4, 8, 16, 32, or 64
ExtremeSwitching X440-G2 N/A
IP route sharing (total combinations of gateway sets)—maximum number of combinations of sets of adjacent gateways used by multipath OSPF, BGP, IS-IS, or static routes. Summit X670-G2, X770
  • if maximum gateways is 2
  • if maximum gateways is 4
  • if maximum gateways is 8
  • if maximum gateways is 16 (default)
  • if maximum gateways is 32
  • if maximum gateways is 64
  • 1,022
  • 1,022
  • 1,022
  • 1,022
  • 510
  • 254
Summit X460-G2, X450-G2
  • if maximum gateways is 2
  • if maximum gateways is 4
  • if maximum gateways is 8
  • if maximum gateways is 16 (default)
  • if maximum gateways is 32
  • if maximum gateways is 64
  • 1,022
  • 1,022
  • 510
  • 254
  • 126
  • 62
ExtremeSwitching X620
  • if maximum gateways is 2
  • if maximum gateways is 4
  • if maximum gateways is 8
  • if maximum gateways is 16 (default)
  • if maximum gateways is 32
  • if maximum gateways is 64
  • 126
  • 126
  • 126
  • 126
  • 62
  • 30
ExtremeSwitching X690, X590
  • if maximum gateways is 2
  • if maximum gateways is 4
  • if maximum gateways is 8
  • if maximum gateways is 16 (default)
  • if maximum gateways is 32
  • if maximum gateways is 64
Note: The values here represent the maximum attainable ECMP groups of which, due to the RIOT feature, half are reserved for overlay and half for underlay routing. For more information about RIOT, see the ExtremeXOS 22.7 User Guide .
  • 4,094
  • 4,094
  • 2,046
  • 1,022
  • 510
  • 254
ExtremeSwitching X870
  • if maximum gateways is 2
  • if maximum gateways is 4
  • if maximum gateways is 8
  • if maximum gateways is 16 (default)
  • if maximum gateways is 32
  • if maximum gateways is 64
  • 2,046
  • 2,046
  • 2,046
  • 1,022
  • 510
  • 254
ExtremeSwitching X440-G2 N/A
IP multinetting (secondary IP addresses)—maximum number of secondary IP addresses per VLAN. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 255
Jumbo frames—maximum size supported for jumbo frames, including the CRC. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 9,216
L2 VPN: VCCV (pseudowire Virtual Circuit Connectivity Verification) VPNs per switch—maximum number of VCCV enabled VPLS VPNs. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 16
Summit X450-G2, and ExtremeSwitching X620, X440-G2 N/A
L2 VPN: VPLS MAC addresses—maximum number of MAC addresses learned by a switch. Summit X770 128,000
Summit X670-G2, ExtremeSwitching X690, X590 140,000
Summit X460-G2 55,000
ExtremeSwitching X870 65,000
Summit X450-G2, and ExtremeSwitching X620, X440-G2 N/A
L2 VPN: VPLS VPNs—maximum number of VPLS virtual private networks per switch. Summit X460-G2, X770, X670-G2, ExtremeSwitching X870, X690, X590 1,023
Summit X450-G2, and ExtremeSwitching X620, X440-G2 N/A
L2 VPN: VPLS peers—maximum number of VPLS peers per VPLS instance. Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 64
Summit X450-G2, and ExtremeSwitching X620, X440-G2 N/A
L2 VPN: LDP pseudowires—maximum number of pseudowires per switch. Summit X770, X670-G2, X460-G2, and ExtremeSwitching X870, X690, X590 7,000
Summit X450-G2, and ExtremeSwitching X620, X440-G2 N/A
L2 VPN: static pseudowires—maximum number of static pseudowires per switch. Summit X670-G2, X460-G2, X770, ExtremeSwitching X870, X690, X590 7,000
Summit X450-G2, and ExtremeSwitching X620, X440-G2 N/A
L2 VPN: Virtual Private Wire Service (VPWS) VPNs—maximum number of virtual private networks per switch. Summit X670-G2, ExtremeSwitching X870, X690, X590 4,090
Summit X460-G2 1,023
Summit X770 4,000
Summit X450-G2, and ExtremeSwitching X620, X440-G2 N/A
Layer-2 IPMC forwarding caches—(IGMP/MLD/PIM snooping) in mac-vlan mode.
Note:
  • The internal lookup table configuration used is "l2-and-l3”.
  • IPv6 and IPv4 L2 IPMC scaling is the same for this mode.
  • Layer-2 IPMC forwarding cache limits—(IGMP/MLD/PIM snooping) in mixed-mode are the same.
Summit X770, X670-G2 73,000
Summit X460-G2 24,000
Summit X450-G2 14,000
ExtremeSwitching X620, X440-G2 5,000
ExtremeSwitching X870 36,000
ExtremeSwitching X690, X590 67,000
Layer-3 IPv4 Multicast—maximum number of <S,G,V> entries installed in the hardware (IP multicast compression enabled).
Note:
  • Limit value is the same for MVR senders, PIM Snooping entries. PIM SSM cache, IGMP senders, PIM cache.
  • The internal lookup table configuration used is "more l3-and-ipmc”.
  • Assumes source-group-vlan mode as look up key.
  • Layer 3 IPMC cache limit in mixed mode also has the same value.
Summit X460-G2 26,000
Summit X450-G2 21,000
Summit X770, X670-G2 77,500
ExtremeSwitching X620, X440-G2 1,500
ExtremeSwitching X870 52,000
ExtremeSwitching X690, X590 93,000
Layer-3 IPv6 Multicast—maximum number of <S,G,V> entries installed in the hardware (IP multicast compression enabled).
Note:
  • Limit value is the same for MLD sender per switch, PIM IPv6 cache.
  • The internal lookup table configuration used is "more l3-and-ipmc”.
  • Assumes source-group-vlan mode as lookup key.
Summit X770, X670-G2 30,000
Summit X460-G2 14,000
Summit X450-G2 10,000
ExtremeSwitching X620, X440-G2 700
ExtremeSwitching X870 18,000
ExtremeSwitching X690, X590 48,000
Load sharing—maximum number of load sharing groups.
Note: The actual number of load-sharing groups that can be configured is limited by the number of physical ports present in the switch or SummitStack.
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 128
Load sharing—maximum number of ports per load-sharing group. For standalone and stacked: ExtremeSwitching X620, X440-G2 8
For standalone: Summit X770, X670-G2, X460-G2, X450-G2, ExtremeSwitching X870, X690, X590 32
For stacked: Summit X770, X670-G2, X460-G2, X450-G2, X670-G2, and ExtremeSwitching X870, X690, X590 64
Logged messages—maximum number of messages logged locally on the system. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 20,000
MAC-based security—maximum number of MAC-based security policies. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 1,024
MAC Locking—Maximum number of MAC locking stations that can be learned on a port. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

64 (static MAC locking stations)

600 (first arrival MAC locking stations)

Meters—maximum number of meters supported. Summit X460-G2, X450-G2, X670-G2, X770, ExtremeSwitching X440-G2, X620, X870, X690, X590 2,048
Maximum mirroring instances Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590
TableOtherOnly two or four mirroring instances will be active at a time, depending on the mirroring filter added to it. There are four hardware resource slots. Each single instance uses one such slot, while each ingress plus egress instance uses two slots. You can use a total of four slots, while there are no more than two egress instances. The maximum possible combination for mirroring instances:
  1. 4 ingress
  2. 3 ingress + 1 egress
  3. 2 ingress + 2 egress
  4. 2 (ingress + egress)
  5. 1 (ingress + egress) + 2 ingress
  6. 1 (ingress + egress) + 1 egress + 1 ingress
16 (including default mirroring instance)
ExtremeSwitching X620, X440-G2
Note: For stacks containing X620 or X440-G2, maximum supported egress mirror instances is 1.
1 (egress)
Mirroring (filters)—maximum number of mirroring filters.
Note: This is the number of filters across all the active mirroring instances.
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 128
Mirroring, one-to-many (filters)—maximum number of one-to-many mirroring filters.
Note: This is the number of filters across all the active mirroring instances.
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 128
Mirroring, one-to-many (monitor port)—maximum number of one-to-many monitor ports. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 16
MLAG ports—maximum number of MLAG ports allowed. Summit X670-G2, ExtremeSwitching X690 71
ExtremeSwitching X440-G2, Summit X450-G2 51
Summit X460-G2 53
Summit X770 103
ExtremeSwitching X620 15
ExtremeSwitching X870 127
ExtremeSwitching X590 35
MLAG peers—maximum number of MLAG peers allowed. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 2
MPLS RSVP-TE interfaces—maximum number of interfaces. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690 32
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS RSVP-TE ingress LSPs—maximum number of ingress LSPs. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690 2,000
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS RSVP-TE egress LSPs—maximum number of egress LSPs. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690 2,000
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS RSVP-TE transit LSPs—maximum number of transit LSPs. Summit X460-G2, X670-G2, X770 2,000
ExtremeSwitching X870, X690 4,000
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS RSVP-TE paths—maximum number of paths. Summit X460-G2, X770 1,000
Summit X670-G2, ExtremeSwitching X870, X690 2,000
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS RSVP-TE profiles—maximum number of profiles. Summit X460-G2, X770 1,000
Summit X670-G2, ExtremeSwitching X870, X690 2,000
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS RSVP-TE EROs—maximum number of EROs per path. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690 64
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS LDP peers—maximum number of MPLS LDP peers per switch. Summit X770 64
Summit X670-G2, X460-G2, ExtremeSwitching X870, X690 128
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS LDP adjacencies—maximum number of MPLS LDP adjacencies per switch. Summit X460-G2 50
Summit X770, X670-G2, ExtremeSwitching X870, X690 64
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS LDP ingress LSPs—maximum number of MPLS LSPs that can originate from a switch. Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690 2,048
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS LDP-enabled interfaces—maximum number of MPLS LDP configured interfaces per switch. Summit X770 64
Summit X670-G2, X460-G2, ExtremeSwitching X870, X690 128
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS LDP transit LSPs—maximum number of MPLS transit LSPs per switch. Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690 4,000
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS LDP egress LSPs—maximum number of MPLS egress LSPs that can terminate on a switch. Summit X670-G2, X460-G2, X770, ExtremeSwitching X870, X690 4,000
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS static egress LSPs—maximum number of static egress LSPs. Summit X460-G2 7,116
Summit X770, ExtremeSwitching X870, X690 8,000
Summit X670-G2 15,308
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS static ingress LSPs—maximum number of static ingress LSPs. Summit X460-G2, ExtremeSwitching X870, X690 4,000
Summit X770, X670-G2 2,048
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
MPLS static transit LSPs—maximum number of static transit LSPs Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690 4,000
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
Multicast listener discovery (MLD) snooping per-VLAN filters—maximum number of VLANs supported in per-VLAN MLD snooping mode. Summit X460-G2, X770, X670-G2, ExtremeSwitching X870 1,200
Summit X450-G2 512
ExtremeSwitching X620, X440-G2 600
ExtremeSwitching X690, X590 1,500
Multicast listener discovery (MLD)v1 subscribers—maximum number of MLDv1 subscribers per port.n Summit X770, X670-G2, X450-G2, X460-G2 4,000
ExtremeSwitching X620, X440-G2 3,500
ExtremeSwitching X870, X690, X590 4,000
Multicast listener discovery (MLD)v1 subscribers—maximum number of MLDv1 subscribers per switch.n Summit X460-G2, X450-G2, ExtremeSwitching X620, X440-G2 10,000
Summit X770, X670-G2 30,000
ExtremeSwitching X870, X690, X590 45,000
Multicast listener discovery (MLD)v2 subscribers—maximum number of MLDv2 subscribers per port.n Summit X770, X670-G2, X460-G2, X450-G2 4,000
ExtremeSwitching X620, X440-G2 3,500
ExtremeSwitching X870, X690, X590 4,000
Multicast listener discovery (MLD)v2 subscribers—maximum number of MLDv2 subscribers per switch.n Summit X770, X670-G2 30,000
Summit X460-G2, X450-G2, ExtremeSwitching X620, X440-G2 10,000
ExtremeSwitching X870, X690, X590 45,000
Multicast listener discovery (MLD)v2 maximum source per group—maximum number of source addresses per group. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 200
Multicast listener discovery (MLD) SSM-map entries—maximum number of MLD SSM mapping entries. Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 500
ExtremeSwitching X440-G2, X620 50
Multicast listener discovery (MLD) SSM-MAP entries—maximum number of sources per group in MLD SSM mapping entries. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 50
Network Login—maximum number of clients being authenticated on MAC-based VLAN enabled ports. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 1,024
Network Login—maximum number of clients being authenticated with policy mode enabled with TCI overwrite enabled. Summit X450-G2, X460-G2, ExtremeSwitching X590 1,024
Summit X670-G2, X770, ExtremeSwitching X870, X690 512
ExtremeSwitching X620, X440-G2 256
Network Login—maximum number of dynamic VLANs. Summit X460-G2, X450-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 2,000
ExtremeSwitching X440-G2, X620 1,024
Network Login VLAN VSAs—maximum number of VLANs a client can be authenticated on at any given time. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 10
Network Service Identifiers (NSI)/VLAN mappings—maximum number of VLANs to NSI mappings. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 94
Node Alias—maximum number of entries per slot. Summit X450-G2, X460-G2, X670-G2, X770 and ExtremeSwitching X620, X440-G2, X870, X690, X590 8,192
ONEPolicy Roles/Profiles—maximum number of policy roles/profiles. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 63
ONEPolicy Rules per Role/Profile—maximum number of rules per role/policy. Summit X450-G2, X460-G2 IPv6 rules: 256

IPv4 rules: 256

L2 Rules: 184

MAC Rules: 256

Summit X670-G2, X770, ExtremeSwitching X870 IPv6 Rules: 256

L2 Rules: 184

MAC Rules: 256

IPv4 Rules: 256

ExtremeSwitching X620, X440-G2 IPv6 and Mac Rules: 0

Ipv4 Rules: 256 (per switch)

L2 Rules: 184 (per switch)

ExtremeSwitching X690, X590

IPv4 Rules: 512

IPv6 Rules: 512

MAC Rules: 512

L2 Rules: 440

ONEPolicy Authenticated Users per Switch—maximum number of authenticated users per port only with TCI-Overwrite enabled. Summit X450-G2, X460-G2, and ExtremeSwitching X590 1,024
Summit X670-G2, X770, ExtremeSwitching X690, X870 512
ExtremeSwitching X620, X440-G2 256
Stacking Depends on the stack nodes.
ONEPolicy Authenticated Users per Switch—maximum number of authenticated users per switch with TCI-Overwrite disabled.
Note: The maximum values assume 75% utilization of VLAN-XLATE hash table.
ExtremeSwitching X690, X590 24,576
Summit X670-G2, X460-G2, ExtremeSwitching X870 12,288
Summit X770, X450-G2 6,144
ExtremeSwitching X620, X440-G2 1,536
Stacking 1,536–65,534
ONEPolicy Authenticated Users per Port per Switch— maximum number of authenticated users per port per switch with TCI overwrite disabled.
Note: The maximum values assume 75% utilization of VLAN-XLATE hash table.
Summit X450-G2, X770 6,144
Summit 460-G2, X670-G2, and ExtremeSwitching X870 12,288
ExtremeSwtiching X690, X590 24,576
ExtemeSwtiching X440-G2, X620 1,536
ONEPolicy Authenticated Users per Port per Switch— maximum number of authenticated users per port with only with TCI-Overwrite enabled. Summit X450-G2, X460-G2, ExtremeSwitching X590 1,024
Summit X670-G2, X770, ExtremeSwitching X870, X690 512
ExtremeSwitching X620, X440-G2 256
ONEPolicy Permit/Deny Traffic Classification Rules Types—total maximum number of unique permit/deny traffic classification rules types (system/stack). Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870 952
ExtremeSwitching X620, X440-G2 440
ExtremeSwitching X690, X590 1,976
ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique MAC permit/deny traffic classification rules types (macsource/macdest). Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870 256
ExtremeSwitching X620, X440-G2 N/A
ExtremeSwitching X690, X590 512
ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique IPv6 permit/deny traffic classification rules types (ipv6dest). Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870 256
ExtremeSwitching X620, X440-G2 N/A
ExtremeSwitching X690, X590 512
ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique IPv4 permit/deny traffic classification rules (typesipsource / ipdest / ipfrag / udpsourceportIP / udpdestportIP / tcpsourceportIP / tcpdestportIP / ipttl / iptos / iptype). Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X620, X440-G2, X870 256
ExtremeSwitching X690, X590 512
ONEPolicy Permit/Deny Traffic Classification Rules Types—maximum number of unique Layer 2 permit/deny traffic classification rules (ethertype/port). Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870 184
ExtremeSwitching X620, X440-G2 184
ExtremeSwitching X690, X590 440
Policy-based routing (PBR) redundancy—maximum number of flow-redirects.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

256 o
Policy-based routing (PBR) redundancy—maximum number of next hops per each flow-direct.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

32o
Private VLANs—maximum number of subscribers. Assumes a minimum of one port per network and subscriber VLAN. Summit X770 103
Summit X670-G2 63
Summit X460-G2 53
Summit X450-G2 51
ExtremeSwitching X440-G2 47
ExtremeSwitching X620 15
ExtremeSwitching X870 127
ExtremeSwitching X690 71
ExtremeSwitching X590 31
Private VLANs—maximum number of private VLANs with an IP address on the network VLAN.
Note: This limit is dependent on the maximum number of private VLANs in an L2-only environment if the configuration has tagged and translated ports.
Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 1,024
Summit X450-G2 510
ExtremeSwitching X440-G2 255
ExtremeSwitching X620 510
Private VLANs—maximum number of private VLANs in an L2-only environment. Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 1,280
Summit X450-G2 597
ExtremeSwitching X440-G2, X620 255
PTP/1588v2 Clock Ports Summit X770, X460-G2, X670-G2 32 for boundary clock

1 for ordinary clock

 
ExtremeSwitching X440-G2, X620, X870, X690, X590 N/A
PTP/1588v2 Clock Instances Summit X770, X670-G2, X460-G2 2 combinations:
  • Transparent clock + ordinary clock
  • Transparent clock + boundary clock
ExtremeSwitching X440-G2, X620, X870, X690, X590 N/A
PTP/1588v2 Unicast Static Slaves Summit X770, X670-G2, X460-G2 40 entries per clock port
ExtremeSwitching X440-G2, X620, X870, X690, X590 N/A
PTP/1588v2 Unicast Static Masters Summit X770, X670-G2, X460-G2 10 entries per clock type
ExtremeSwitching X440-G2, X620, X870, X690, X590 N/A
Route policies—suggested maximum number of lines in a route policy file.

Summit X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

10,000
RIP Learned Routes—maximum number of RIP routes supported without aggregation.

Summit X770, X670-G2, X460-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590

10,000
RIP interfaces on a single router—recommended maximum number of RIP routed interfaces on a switch. Summit X670-G2, X460-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 256
ExtremeSwitching X440-G2, X620 128
RIPng learned routes—maximum number of RIPng routes. Summit X670-G2, X460-G2, X770, X450-G2, X870, X690, X590 3,000
ExtremeSwitching X440-G2, X620 N/A
Spanning Tree (maximum STPDs)—maximum number of Spanning Tree Domains on port mode EMISTP.
Note: STP limits are the same for all license levels.
Summit X450-G2, X770, X670-G2, X460-G2, and ExtremeSwitching X620, X870, X690, X590 64
ExtremeSwitching X440-G2 32
Spanning Tree PVST+—maximum number of port mode PVST domains.
Note: For all platforms, the maximum number of active ports per PVST domain depends on the maximum number of spanning tree ports supported on given platform. For example, ExtremeSwitching X670-G2 supports 256 PVST domains (maximum), and 4,096 STP ports (maximum), so the maximum number of active ports per PVST domain would be 16 ports (4,096 ÷ 256).
Summit X770, X670-G2, and ExtremeSwitching X620 256
Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2 128
ExtremeSwitching X870, X690, X590 384
Spanning Tree—maximum number of multiple spanning tree instances (MSTI) domains. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X870, X690, X590 64
ExtremeSwitching X440-G2 32
Spanning Tree—maximum number of VLANs per MSTI.
Note: Maximum number of 10 active ports per VLAN when all 500 VLANs are in one MSTI.
Summit X770, X670-G2 500
Summit X460-G2, X450-G2, ExtremeSwitching X620, X870, X690, X590 600
ExtremeSwitching X440-G2 256
Spanning Tree—maximum number of VLANs on all MSTP instances. Summit X770, X670-G2, X460-G2, X450-G2, ExtremeSwitching X620, X870, X690, X590 1,024
ExtremeSwitching X440-G2 512
Spanning Tree (802.1d domains)—maximum number of 802.1d domains per port.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

1
Spanning Tree (number of ports)—maximum number of ports including all Spanning Tree domains. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X870, X690, X590 4,096
ExtremeSwitching X440-G2 2,048
Spanning Tree (maximum VLANs)—maximum number of STP-protected VLANs (dot1d and dot1w). Summit X770, X670-G2, X460-G2, X450-G2, and ExtremeSwitching X620, X870, X690, X590 1,024
ExtremeSwitching X440-G2 600
SSH (number of sessions)—maximum number of simultaneous SSH sessions. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 8
Static MAC multicast FDB entries—maximum number of permanent multicast MAC entries configured into the FDB. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 1,024
Syslog servers—maximum number of simultaneous Syslog servers that are supported. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 16
Syslog targets—maximum number of configurable Syslog targets. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 16
Telnet (number of sessions)—maximum number of simultaneous Telnet sessions. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 8
Virtual routers—maximum number of user-created virtual routers that can be created on a switch. Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 63
ExtremeSwitching X440-G2, X620 16 (local-only VRs)
Virtual router forwarding (VRFs)—maximum number of VRFs that can be created on a switch.
Note: * Subject to other system limitations.
Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 960 * 
ExtremeSwitching X440-G2, X620 16 (local-only VRFs)
Virtual router protocols per VR—maximum number of routing protocols per VR. Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 8
ExtremeSwitching X440-G2, X620 N/A
Virtual router protocols per switch—maximum number of VR protocols per switch. Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 64 
ExtremeSwitching X440-G2, X620 N/A
VLAN aggregation—maximum number of port-VLAN combinations on any one superVLAN and all of its subVLANs. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 1,000
VLANs—includes all VLANs.
Note: ExtremeXOS supports only 4,092 user-configurable VLANs. (VLAN 1 is the default VLAN, and 4,095 is the management VLAN, and you may not configure them.)
Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 4,094
VLANs (Layer 2)—maximum number of Layer 2 VLANs. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 4,094
VLANs (Layer 3)—maximum number of VLANs performing IPv4 and/or IPv6 routing. Excludes sub-VLANs. Summit X460-G2, X770, X670-G2, X450-G2, ExtremeSwitching X870, X690, X590 2,048  
ExtremeSwitching X440-G2, X620 510
VLANs (maximum active port-based)—maximum active ports per VLAN when 4,094 VLANs are configured with default license. Summit X670-G2, ExtremeSwitching X870, X690, X590 32
ExtremeSwitching X440-G2 28
Summit X460-G2, X770 26
ExtremeSwitching X620 16
Summit X450-G2 29
Summit X460-G2 24
VLANs (maximum active protocol-sensitive filters)—number of simultaneously active protocol filters in the switch.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2. X870, X690, X590

16

VLAN translation—maximum number of translation VLANs. Assumes a minimum of one port per translation and member VLAN. Summit X770 103
Summit X670-G2 63
Summit X460-G2 53
Summit X450-G2 51
ExtremeSwitching X620 15
ExtremeSwitching X440-G2 47
ExtremeSwitching X870 127
ExtremeSwitching X690 71
ExtremeSwitching X590 31
VLAN translation—maximum number of translation VLAN pairs with an IP address on the translation VLAN.
Note: This limit is dependent on the maximum number of translation VLAN pairs in an L2-only environment if the configuration includes tagged and translated ports.
Summit X770, X670-G2, ExtremeSwitching X870, X690, X590 1,024
Summit X450-G2 512
ExtremeSwitching X620 510
ExtremeSwitching X440-G2 255
VLAN translation—maximum number of translation VLAN pairs in an L2-only environment. Summit X450-G2, X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 2,046
ExtremeSwitching X440-G2, X620 255
XML requests—maximum number of XML requests per second.
Note: Limits are dependent on load and type of XML request. These values are dynamic ACL data requests.
Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 10 with 100 DACLs
XNV authentication—maximum number of VMs that can be processed (combination of local and network VMs). Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 2,048
Summit X450-G2, and ExtremeSwitching X440-G2, X620 1,024
XNV database entries—maximum number of VM database entries (combination of local and network VMs). Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 16,000
XNV database entries—maximum number of VPP database entries (combination of local and network VPPs). Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 2,048
XNV dynamic VLAN—Maximum number of dynamic VLANs created (from VPPs /local VMs). Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 2,048
XNV local VPPs—maximum number of XNV local VPPs. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

2,048 ingress

512 egress

XNV policies/dynamic ACLs—maximum number of policies/dynamic ACLs that can be configured per VPP. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

8 ingress

4 egress

XNV network VPPs—maximum number of XNV network VPPs.p Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

2,048 ingress

512 egress

Supported Limits for Advanced Edge License

The following table shows supported limits for features in the Advanced Edge License.

Table 2. Supported Limits for Advanced Edge License
Metric Product Limit
BGP auto-peering—maximum number of auto-peering nodes and VTEPs. Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 64
BGP auto-peering attached IPv4 hosts— maximum number of attached IPv4 hosts. Summit X670-G2, X770 16,000
ExtremeSwitching X870, X690, X590 64,000
BGP auto-peering attached IPv6 hosts— maximum number of attached IPv6 hosts. Summit X670-G2, X770 254
ExtremeSwitching X870, X690, X590 8,000
BGP auto-peering ECMP—maximum number equal cost multipath for auto-peering.
Note: * Subject to the limitation imposed by the number of physical ports on a switch.
Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 16*
BGP auto-peering maximum IPv4 prefixes with ECMP—Maximum number of IPv4 Network prefixes with ECMP. Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 64,000
BGP auto-peering maximum IPv6 prefixes with ECMP—Maximum number of IPv6 Network prefixes with ECMP. Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 8,000
BGP auto-peering MLAG peers—maximum MLAG peers per AutoBGP node. Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 1
BGP auto-peering VRFs—maximum number of VRFs. Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 64
BGP auto-peering EVPN instances—maximum EVPN instances. Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 4,096
BGP auto-peering asymmetrical routing tenant VLANs—maximum number of tenant VLANs supporting asymmetric routing. Summit X670-G2, X770, ExtremeSwitching X690, X870, X590 1,024
EAPS domains—maximum number of EAPS domains.
Note: An EAPS ring that is being spatially reused cannot have more than four configured EAPS domains.
ExtremeSwitching X870, X690, X590 128
Summit X670-G2, X450-G2, X460-G2, X770 64
ExtremeSwitching X440-G2, X620 32
EAPSv2 protected VLANs—maximum number of protected VLANs. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X440-G2, X620 500
ExtremeSwitching X870, X690, X590 2,000
ERPS domains—maximum number of ERPS domains without CFM configured. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 32
ERPS domains—maximum number of ERPS domains with CFM configured. Summit X450-G2, X670-G2, X770, and ExtremeSwitching X620, X870, X690, X590 16
Summit X460-G2 32
ERPSv1 protected VLANs—maximum number of protected VLANs. Summit X450-G2, X460-G2, X670-G2, and ExtremeSwitching X870, X690, X590 2,000
Summit X770, ExtremeSwitching X620, X440-G2 1,000
ERPSv2 protected VLANs—maximum number of protected VLANs. Summit X450-G2, X460-G2, X670-G2, and ExtremeSwitching X870, X690, X590 2,000
Summit X770, ExtremeSwitching X620, X440-G2 500
ESRP groups—maximum number of ESRP groups Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X440-G2, X620, X870, X690, X590 32
ESRP domains—maximum number of ESRP domains. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 64
ESRP L2 VLANs—maximum number of ESRP VLANs without an IP address configured. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 1,000
ESRP L3 VLANs—maximum number of ESRP VLANs with an IP address configured. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 511
ESRP (maximum ping tracks)—maximum number of ping tracks per VLAN. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 8
ESRP (IP route tracks)—maximum IP route tracks per VLAN. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 8
ESRP (VLAN tracks)—maximum number of VLAN tracks per VLAN. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 1
OSPFv2/v3 ECMP—maximum number of equal cost multipath OSPFv2 and OSPFv3. Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 64
ExtremeSwitching X620 4
ExtremeSwitching X440-G2 N/A
OSPFv2 areas—as an ABR, how many OSPF areas are supported within the same switch. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 8
Summit X450-G2, ExtremeSwitching X440-G2, X620 4
OSPFv2 external routes—recommended maximum number of external routes contained in an OSPF LSDB. ExtremeSwitching X870, X690, X590 10,000
Summit X770, X670-G2, X460-G2 5,000
Summit X450-G2, ExtremeSwitching X440-G2, X620 2,400
OSPFv2 inter- or intra-area routes—recommended maximum number of inter- or intra-area routes contained in an OSPF LSDB with one ABR in OSPF domain. ExtremeSwitching X870, X690, X590 4,000
Summit X670-G2, X460-G2, X770 2,000
Summit X450-G2, and ExtremeSwitching X440-G2, X620 1,000
OSPFv2 interfaces—recommended maximum number of OSPF interfaces on a switch (active interfaces only). Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 4
OSPFv2 links—maximum number of links in the router LSA. Summit X460-G2, X670-G2, ExtremeSwitching X870, X690, X590 400
Summit X450-G2, and ExtremeSwitching X620, X440-G2 4
Summit X770 419
OSPFv2 neighbors—maximum number of supported OSPF adjacencies. Summit X450-G2, X770, X670-G2, X460-G2, and ExtremeSwitching X440-G2, X620, X870, X690, X590 4
OSPFv2 routers in a single area—recommended maximum number of routers in a single OSPF area. ExtremeSwitching X870, X690, X590 100
Summit X770, X670-G2, X460-G2 50
Summit X450-G2, ExtremeSwitching X440-G2, X620 4
OSPFv2 virtual links—maximum number of supported OSPF virtual links. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 32
Summit X450-G2, and ExtremeSwitching X440-G2, X620 4
OSPFv3 areas—as an ABR, the maximum number of supported OSPFv3 areas. ExtremeSwitching X870, X690, X590 100
Summit X460-G2, X670-G2, X770 16
Summit X450-G2, ExtremeSwitching X440-G2, X620 4
OSPFv3 external routes—recommended maximum number of external routes. Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 10,000
Summit X450-G2, ExtremeSwitching X440-G2, X620 1,200
OSPFv3 inter- or intra-area routes—recommended maximum number of inter- or intra-area routes. ExtremeSwitching X870, X690, X590 4.000
Summit X770, X670-G2, X460-G2 3,000
Summit X450-G2, ExtremeSwitching X440-G2, X620 500
OSPFv3 interfaces—maximum number of OSPFv3 interfaces. Summit X770, X670-G2, X460-G2, X450-G2, ExtremeSwitching X870, X690, X440-G2, X620, X590 4
OSPFv3 neighbors—maximum number of OSPFv3 neighbors. Summit X450-G2, X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X440-G2, X620, X590 4
OSPFv3 virtual links—maximum number of OSPFv3 virtual links supported. Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 16
Summit X450-G2, ExtremeSwitching X440-G2, X620 4
OVSDB Manager Connections—Maximum number of connections to managers that can be configured (either of TCP, PTCP, SSL, or PSSL). Summit X770, X670-G2, ExtremeSwitching X870, X690, X590 8
Smmit X450-G2 N/A
OVSDB Managed Switches—Maximum number of OVSDB-managed switches. Summit X770, X670-G2, ExtremeSwitching X870, X690, X590 1
Smmit X450-G2 N/A
PIM IPv4 (maximum interfaces)—maximum number of PIM active interfaces. Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X440-G2, X620, X690, X590 4
PIM IPv4 Limits—maximum number of multicast groups per dynamic rendezvous point.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

180
PIM IPv4 Limits—maximum number of multicast groups per static rendezvous point.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

3,000 (depends on policy file limits)
PIM IPv4 Limits—maximum number of multicast sources per group. Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 5,000
ExtremeSwitching X440-G2, X620 1,500
PIM IPv4 Limits—maximum number of dynamic rendezvous points per multicast group.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

145
PIM IPv4 Limits—static rendezvous points.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

32
PIM IPv6 (maximum interfaces)—maximum number of PIM active interfaces. Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X440-G2, X620, X690, X590 4
PIM IPv6 Limits—maximum number of multicast sources per group. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 1,750
Summit X450-G2 1,500
ExtremeSwitching X440-G2, X620 550
PIM IPv6 Limits—maximum number of multicast groups per dynamic rendezvous point.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

70

PIM IPv6 Limits—maximum number of multicast groups per static rendezvous point.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

3,000 (depends on policy file limits)

PIM IPv6 Limits—maximum number of dynamic rendezvous points per multicast group.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

64
PIM IPv6 Limits—maximum number of secondary address per interface.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

70
PIM IPv6 Limits—static rendezvous points.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

32
Port-specific VLAN tags—maximum number of port-specific VLAN tags. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 1,023
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
Port-specific VLAN tags—maximum number of port-specific VLAN tag ports. Summit X770, X670-G2 4,000
Summit X460-G2, ExtremeSwitching X870, X690, X590 4,000
Summit X450-G2, and ExtremeSwitching X440-G2, X620 N/A
VRRP (v2/v3-IPv4) (maximum instances)—maximum number of VRRP instances for a single switch, with Advanced Edge license or higher.
Note: These limits are applicable for Fabric Routing configuration also.
Note: Number of groups configured should not exceed the number of individual VRs supported (that is, in normal mode) for that platform type.

Normal Mode (as individual VRs):

Summit X770, X670-G2, X460-G2, X450-G2, and ExtremeSwitching X870, X690, X590 511
ExtremeSwitching X440-G2, X620 128

Scaled Mode (with groups):

Summit X770, X670-G2, X460-G2, X450-G2, and ExtremeSwitching X870, X690, X590

2,048

ExtremeSwitching X440-G2, X620 128
VRRP (v3-IPv6) (maximum instances)—maximum number of VRRP instances for a single switch, with Advanced Edge license or higher. (VRRP-VRRPv3-IPv6)
Note: These limits are applicable for Fabric Routing configuration also.
Note: Number of groups configured should not exceed the number of individual VRs supported (that is, in normal mode) for that platform type.

Normal Mode (as individual VRs):

Summit X770, X670-G2, X460-G2, X450-G2, and ExtremeSwitching X870, X690, X590 511
ExtremeSwitching X440-G2, X620 128

Scaled Mode (with groups):

Summit X770, X670-G2, X460-G2, X450-G2, and ExtremeSwitching X870, X690, X590

2,048

ExtremeSwitching X440-G2, X620 128
VRRP (v2/v3-IPv4/IPv6) (maximum VRID)—maximum number of unique VRID numbers per switch.

Summit X770, X670-G2, X460-G2, X450-G2 and ExtremeSwitching X440-G2, X620, X870, X690, X590

Note: With Advanced Edge license or higher.

255

VRRP (v2/v3-IPv4/IPv6) (maximum VRIDs per VLAN)—maximum number of VRIDs per VLAN.

Summit X770, X670-G2, X460-G2, X450-G2 and ExtremeSwitching X440-G2, X620, X870, X690, X590

Note: With Advanced Edge license or higher.

255

VRRP (v2/v3-IPv4/IPv6) (maximum ping tracks)—maximum number of ping tracks per VLAN.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

Note: With Advanced Edge license or higher.

8

VRRP (maximum ping tracks)—maximum number of ping tracks per VRRP Instance under 128 VRRP instances, with Advanced Edge license or higher.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

8 (20 centisecond or 1 second hello interval)
VRRP (v3-IPv6) (maximum ping tracks)—maximum number of ping tracks per VRRP Instance under 128 VRRP instances, with Advanced Edge license or higher.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

8 (20 centisecond or 1 second hello interval)
VRRP (v2/v3-IPv4/IPv6) (maximum iproute tracks)—maximum number of IP route tracks per VLAN.

Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590

8
VRRP (v2/v3-IPv4/IPv6)—maximum number of VLAN tracks per VLAN. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X620, X440-G2, X870, X690, X590 8
VXLAN—maximum virtual networks.
Note: Every VPLS instance/PSTag VLAN reduces this limit by 1.
Note: Assumption is all BUM (broadcast/unknown-unicast/multicast) FDB entries are pointing to the same set of RTEPs when all VNETs use explicit flooding. Depends on whether all VNETs use standard or explicit and the number of tenant VLAN ports.
Summit X670-G2, X770, and ExtremeSwiching X870, X690, X590 2,048–4,000
Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2, X620 N/A
VXLAN—maximum tenant VLANs plus port combinations
Note: Every (VPLS/PSTag VLAN) + port reduces the limit by 1.
Summit X670-G2, X770, and ExtremeSwiching X870, X690, X590 4,096
Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2, X620 N/A
VXLAN—maximum static MAC to IP bindings.
Note: Every FDB entry configured reduces this limit by 1.
Summit X670-G2, X770, and ExtremeSwiching X870, X690, X590 64,000
Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2, X620 N/A
VXLAN—maximum RTEP IP addresses Summit X670-G2, X770, and ExtremeSwitching X870, X690, X590 512
Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2, X620 N/A
VXLAN—maximum virtual networks with dynamic learning and OSPF extensions for VXLAN Summit X670-G2, X770, and ExtremeSwitching X870, X690, X590 4,000
Summit X460-G2, X450-G2, and ExtremeSwitching X440-G2, X620 N/A

Supported Limits for Core License

The following table shows supported limits for features in the Core License.

Table 3. Supported Limits for Core License
Metric Product Limit
BGP (aggregates)—maximum number of BGP aggregates. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 256
Summit X450-G2 204
BGP (networks)—maximum number of BGP networks. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 1,024
Summit X450-G2 820
BGP (peers)—maximum number of BGP peers.
Note: With default keepalive and hold timers.
Summit X460-G2, X670-G2, X770, ExtremeSwitching X870 128
ExtremeSwitching X690, X590 300
Summit X450-G2 100
BGP (peer groups)—maximum number of BGP peer groups. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 64
Summit X450-G2 50
BGP (policy entries)—maximum number of BGP policy entries per route policy. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 256
Summit X450-G2 204
BGP (policy statements)—maximum number of BGP policy statements per route policy. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 1,024
Summit X450-G2 820
BGP multicast address-family routes—maximum number of multicast address-family routes. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 25,000
Summit X450-G2 20,000
BGP (unicast address-family routes)—maximum number of unicast address-family routes. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 (at default) 25,000
ExtremeSwitching X870, X690, X590 (with ALPM enabled) 100,000
Summit X450-G2 20,000
BGP (non-unique routes)—maximum number of non-unique BGP routes. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 25,000
Summit X450-G2 20,000
BGP ECMP—maximum number of equal cost multipath for BGP and BGPv6. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 2, 4, 8, 16, 32, or 64
Summit X450-G2 64
BGPv6 (unicast address-family routes)—maximum number of unicast address family routes. Summit X460-G2 6,000
Summit X670-G2, X770 8,000
ExtremeSwitching X870, X690, X590 10,000
ExtremeSwitching X870, X690 (with ALPM enabled) 100,000
Summit X450-G2 4,800
BGPv6 (non-unique routes)—maximum number of non-unique BGP routes. Summit X460-G2 18,000
Summit X670-G2, X770, ExtremeSwitching X870, X690, X590 24,000
Summit X450-G2 14,000
GRE Tunnels—maximum number of GRE tunnels. Summit X460-G2, X670-G2, X770, X450-G2, and ExtremeSwitching X870, X690, X590 255
ExtremeSwitching X620, X440G2 N/A
IS-IS adjacencies—maximum number of supported IS-IS adjacencies. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 128
Summit X450-G2 N/A
IS-IS ECMP—maximum number of equal cost multipath for IS-IS. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 2, 4, or 8
Summit X450-G2 N/A
IS-IS interfaces—maximum number of interfaces that can support IS-IS. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 255
Summit X450-G2 N/A
IS-IS routers in an area—recommended maximum number of IS-IS routers in an area. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 256
Summit X450-G2 N/A
IS-IS route origination—recommended maximum number of routes that can be originated by an IS-IS node. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 20,000
Summit X450-G2 N/A
IS-IS IPv4 L1 routes in an L1 router—recommended maximum number of IS-IS Level 1 routes in a Level 1 IS-IS router. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 25,000
Summit X450-G2 N/A
IS-IS IPv4 L2 routes—recommended maximum number of IS-IS Level 2 routes. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 25,000
Summit X450-G2 N/A
IS-IS IPv4 L1 routes in an L1/L2 router—recommended maximum number of IS-IS Level 1 routes in an L1/L2 IS-IS router. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 20,000
Summit X450-G2 N/A
IS-IS IPv6 L1 routes in an L1 router—recommended maximum number of IS-IS Level 1 routes in a Level 1 IS-IS router. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 10,000
Summit X450-G2 N/A
IS-IS IPv6 L2 routes—recommended maximum number of IS-IS Level 2 routes. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 10,000
Summit X450-G2 N/A
IS-IS IPv6 L1 routes in an L1/L2 router—recommended maximum number of IS-IS Level 1 routes in a L1/l2 router. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 10,000
Summit X450-G2 N/A
IS-IS IPv4/IPv6 L1 routes in an L1 router—recommended maximum number of IS-IS Level 1 routes in a Level 1 IS-IS router. The numbers documented are based on 50% IPv4 routes and 50% IPv6 routes. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 20,000
Summit X450-G2 N/A
IS-IS IPv4/IPv6 L2 routes in an L2 router—recommended maximum number of IS-IS Level 2 routes in a Level 2 IS-IS router. The numbers documented are based on 50% IPv4 routes and 50% IPv6 routes. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 20,000
Summit X450-G2 N/A
IS-IS IPv4/IPv6 L1 routes in an L1/L2 router—recommended maximum number of IS-IS Level 1 routes in a Level 1/Level2 IS-IS router. The numbers documented are based on 50% IPv4 routes and 50% IPv6 routes. Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 20,000
Summit X450-G2 N/A
MSDP active peers—maximum number of active MSDP peers. Summit X450-G2, X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 64
MSDP SA cache entries—maximum number of entries in SA cache. Summit X670-G2, X770, ExtremeSwitching X690, X590 14,000
Summit X460-G2 10,000
ExtremeSwitching X870 11,000
Summit X450-G2 8,000
MSDP maximum mesh groups—maximum number of MSDP mesh groups. Summit X450-G2, X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 16
OSPFv2/v3 ECMP—maximum number of equal cost multipath OSPFv2 and OSPFv3. Summit X460-G2, X670-G2, X770, X450-G2, ExtremeSwitching X870, X690, X590 64
OSPFv2 areas—as an ABR, how many OSPF areas are supported within the same switch. Summit X450-G2, X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 8
OSPFv2 external routes—recommended maximum number of external routes contained in an OSPF LSDB. ExtremeSwitching X870, X690, X590 10,000
Summit X770, X670-G2, X460-G2 5,000
Summit X450-G2 4,000
OSPFv2 inter- or intra-area routes—recommended maximum number of inter- or intra-area routes contained in an OSPF LSDB with one ABR in OSPF domain. ExtremeSwitching X870, X690, X590 4,000
Summit X670-G2, X460-G2, X770 2,000
Summit X450-G2 1,600
OSPFv2 interfaces—recommended maximum number of OSPF interfaces on a switch (active interfaces only). Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 400
Summit X450-G2 320
OSPFv2 links—maximum number of links in the router LSA. Summit X460-G2, X670-G2, ExtremeSwitching X870, X690, X590 400
Summit X770 419
Summit X450-G2 320
OSPFv2 neighbors—maximum number of supported OSPF adjacencies. Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 128
Summit X450-G2 96
OSPFv2 routers in a single area—recommended maximum number of routers in a single OSPF area. ExtremeSwitching X870, X690, X590 100
Summit X770, X670-G2, X460-G2 50
Summit X450-G2 40
OSPFv2 virtual links—maximum number of supported OSPF virtual links. Summit X460-G2, X670-G2, X770, ExtremeSwitching X870, X690, X590 32
Summit X450-G2 25
OSPFv3 areas—as an ABR, the maximum number of supported OSPFv3 areas. ExtremeSwitching X870, X690, X590 100
Summit X460-G2, X670-G2, X770 16
Summit X450-G2 12
OSPFv3 external routes—recommended maximum number of external routes. Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 10,000
Summit X450-G2 7,500
OSPFv3 inter- or intra-area routes—recommended maximum number of inter- or intra-area routes. ExtremeSwitching X870, X690, X590 4.000
Summit X770, X670-G2, X460-G2 3,000
Summit X450-G2 500
OSPFv3 interfaces—maximum number of OSPFv3 interfaces. Summit X770 128
Summit X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 256
Summit X450-G2 192
OSPFv3 neighbors—maximum number of OSPFv3 neighbors. Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 64
Summit X450-G2 48
OSPFv3 virtual links—maximum number of OSPFv3 virtual links supported. Summit X770, X670-G2, X460-G2, ExtremeSwitching X870, X690, X590 16
Summit X450-G2 12
PIM IPv4 (maximum interfaces)—maximum number of PIM active interfaces. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 256
PIM IPv4 Limits—maximum number of multicast groups per dynamic rendezvous point. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 180
PIM IPv4 Limits—maximum number of multicast groups per static rendezvous point. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 3,000 (depends on policy file limits)
PIM IPv4 Limits—maximum number of multicast sources per group. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 5,000
PIM IPv4 Limits—maximum number of dynamic rendezvous points per multicast group. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 145
PIM IPv4 Limits—static rendezvous points. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 32
PIM IPv6 (maximum interfaces)—maximum number of PIM active interfaces. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 256
PIM IPv6 Limits—maximum number of multicast sources per group.

Summit X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590

2,500
Summit X450-G2, 1,500
PIM IPv6 Limits—maximum number of multicast groups per dynamic rendezvous point. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590

70

PIM IPv6 Limits—maximum number of multicast groups per static rendezvous point. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590

3,000 (depends on policy file limits)

PIM IPv6 Limits—maximum number of dynamic rendezvous points per multicast group. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 64
PIM IPv6 Limits—maximum number of secondary address per interface. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 70
PIM IPv6 Limits—static rendezvous points. Summit X450-G2, X460-G2, X670-G2, X770, and ExtremeSwitching X870, X690, X590 32


a The table shows the total available. When installing ACL rules bound to a set of ports, rules are replicated for each port if there are ACL counters and counter compression is not enabled or if the ports are Extended Edge Switching extended ports.
c When there are BFD sessions with minimal timer, sessions with default timer should not be used.
f Effective capacity varies based on actual MAC addresses and VLAN IDs used and hash algorithm selected.
g Based on "configure forwarding internal-tables more l2".
h Based on "configure forwarding internal-tables more l3-and-ipmc".
j The limit depends on setting configured with configure iproute reserved-entries.
m The IPv4 and IPv6 multicast entries share the same hardware tables, so the effective number of IPv6 multicast entries depends on the number of IPv4 multicast entries present and vice-versa.
n If IGMP and MLD are simultaneously configured on the switch, the number of effective subscribers supported would be appropriately lessened.
o The total of all PBR next hops on all flow redirects should not exceed 4,096.
p The number of XNV authentications supported based on system ACL limitations.
q Based on "configure forwarding internal-tables more routes".
r Based on configure forwarding internal-tables more routes ipv6-mask-length 128.