Mount the Device

The 5320 Series provides multiple options for mounting or installing the switch.

Mount Options

You can mount or install the device in the following ways:

Mount the Device on a Table

5320 Series switches provide four self-adhesive rubber pads for mounting on tables or other flat surfaces. The pads keep the switch from scratching the supporting surface and help ensure adequate airflow around the switches when they are mounted on top of one another. You can safely place up to four switches on top of one another.

Caution

Caution

Do not place other equipment on top of table-mounted switches.

To mount a switch on a table - or any firm, flat surface - follow these steps.

  1. Carefully separate the four rubber pads that are provided
  2. Apply the pads to the underside of the switch by placing a pad at each corner, ensuring that all corners are aligned. Table Mount: 5320 Series shows the locations for attaching the rubber mounting feet on the switch.
Click to expand in new window
Table Mount: 5320 Series
Attaching the mounting feet to the 5320 series for a table-mount

Install the Device in a Rack

This procedure uses a two-post mounting kit, which accommodates rack posts 3 inches or 6 inches wide.

The two-post rack mount kit XN-2P-RMKIT-006 is required for models 5320- 48T-8XE, 5320-48P-8XE, 5320-24T-8XE, and 5320-24P-8XE. The two-post rack mount kit XN-2P-RMKIT-007 is available for models 5320-16P-4XE and 5320-16P-4XE-DC. The 1U two-post rack mount kit XN-2P-RMKIT-011 is also available for models 5320-16P-4XE and 5320-16P-4XE-DC. The two-post rack mount kit XN-2P-RMKIT-008 is required for models 5320-24T-24S-4XE-XT and 5320-24T-4X-XT. The two-post rack mount kits can also be installed in a four-post rack, using just the two front posts or the two back posts.

The rack mount kit contains an instruction sheet, along with the following components:
  • Mounting ears (2 count)
  • Mounting ear screws (8 count)
Rack mounting ears can support two configurations: flush- and mid-mount.

Take care to load the rack so that it is not top-heavy. Start installing equipment at the bottom and work up.

To attach a switch to a two-post rack, follow these steps.

  1. Attach a mounting bracket to each side of the switch, using the screws provided. Align each mounting bracket so that the flange (ear) faces the front of the switch to flush-mount, or faces the rear of the switch to mid-mount.
    The following figures illustrate how to attach the mounting ears for two common mounting options.
    Note

    Note

    Do not block the air vent on the top of the unit. Leaving a space between units ensures adequate airflow.
    Note

    Note

    Do not overlap rack mounting ears when using the longer mounting ears. Leaving a space between units ensures adequate airflow.
    Click to expand in new window
    Flush-Mount: Attaching 1U mounting ears to 5320-16P models
    Flush-Mount: Attaching 1U mounting ears to 5320-16P models
    Click to expand in new window
    Flush-Mount: Attaching larger mounting ears to 5320-16P models
    Attaching larger mounting ears to 5320-16P models for a flush-mount
    Click to expand in new window
    Flush-Mount: Attaching short mounting ears to models 5320-48P/T and 5320-24P/T
    Attaching short ears to models 5320-48P/T and 5320-24P/T for a flush-mount
    Click to expand in new window
    Flush-Mount: Attaching mounting ears to 5320-24T-4X-XT and 5320-24T-24S-4XE-XT models
    Attaching mounting ears to 5320-24T-4X-XT and 5320-24T-24S-4XE-XT models for a flush mount
    Click to expand in new window
    Mid-Mount: Attaching 1U mounting ears to 5320-16P models
    Mid-Mount: Attaching 1U mounting ears to 5320-16P models
    Click to expand in new window
    Mid-Mount: Attaching larger mounting ears to 5320-16P models
    Attaching longer mounting ears to 5320-16P models for a mid-mount
    Click to expand in new window
    Mid-Mount: Attaching short mounting ears to models 5320-48P/T and 5320-24P/T
    Attaching short ears to models 5320-48P/T and 5320-24P/T for a mid-mount
    Click to expand in new window
    Mid-Mount: Attaching mounting ears to 5320-24T-4X-XT and 5320-24T-24S-4XE-XT models
    Attaching mounting ears to 5320-24T-4X-XT and 5320-24T-24S-4XE-XT models for a mid-mount
  2. With the mounting brackets attached, position the switch between the vertical rack rails of the 19-inch rack.
  3. Fasten the switch securely to the rack rails using four customer-supplied rack screws. Ensure that the threaded length of the screws is within 4 to 5 cm.
    Click to expand in new window
    Flush-Mount: Mounting in a Two- or Four-Post Rack for models 5320-16P-4XE and 5320-16P-4XE-DC
    Flush-Mount: Mounting in a Two- or Four-Post Rack for models 5320-16P-4XE and 5320-16P-4XE-DC
    Click to expand in new window
    Flush-Mount: Mounting in a Two- or Four-Post Rack for models 5320-24T-8XE and 5320-24P-8XE
    Flush-Mount: Mounting in a Two- or Four-Post Rack for models 5320-24T-8XE and 5320-24P-8XE
    Click to expand in new window
    Flush-Mount: Mounting in a Two- or Four-Post Rack for models 5320-48T-8XE and 5320-48P-8XE
    Flush-Mount: Mounting in a Two- or Four-Post Rack for models 5320-48T-8XE and 5320-48P-8XE
    Click to expand in new window
    Flush-Mount: Mounting in a Two- or Four-Post Rack for models 5320-24T-24S-4XE-XT and 5320-24T-4X-XT
    Flush-Mount: Mounting in a Two- or Four-Post Rack for models 5320-24T-24S-4XE-XT and 5320-24T-4X-XT
    Click to expand in new window
    Mid-Mount: Mounting in a Two- or Four-Post Rack for models 5320-24T-24S-4XE-XT and 5320-24T-4X-XT
    Mid-Mount: Mounting in a Two- or Four-Post Rack for models 5320-24T-24S-4XE-XT and 5320-24T-4X-XT

Mount the Device on a Wall (5320-16P models)

The 5320-16P switch models are constructed so that they can be mounted on a wall. Ensure that the wall is strong enough to support the weight of the switch and the attached cables.

Note

Note

The front end of the switch must be facing down, and the power inlet must be facing up when mounting a switch to the wall.

To mount a switch to the wall, follow these steps.

  1. Using the two holes in each short mounting ear, mark the places on the wall to mount the switch. Each mounting ear has two mounting holes, so be sure to make four marks. Be sure to position the marks so that the switch is level when it is mounted.
  2. Drill a hole at each mark.
  3. Insert a provided anchor into each hole. Gently tap each anchor with a hammer, if necessary, to ensure that it is inserted tightly.
  4. Using rack mount screws, attach a wall-mounting ear to the left side of the switch, at the front end. Wall-Mount: Attaching larger mounting ears to 5320-16P models shows the attachment of the screws.
  5. Repeat step 4 for the right side of the switch.
  6. Mount the switch on the wall by screwing a provided wood screw through each hole in the wall-mounting ears into the anchors. Ensure that all screws are securely fastened and that the switch is firmly attached to the wall.
Click to expand in new window
Wall-Mount: Attaching 1U mounting ears to 5320-16P models
Wall-Mount: Attaching 1U mounting ears to 5320-16P models
Click to expand in new window
Wall-Mount: Attaching larger mounting ears to 5320-16P models
Attaching 5320-16P models to a wall for a wall-mount

There is a "cleaner" method of attaching the mounting ears to the switch so that they are tucked under the switch instead of pointing away from the switch. Alternate method of attaching larger mounting ears illustrates attaching the mounting ears so that they are underneath the switch.

Click to expand in new window
Alternate method of attaching 1U mounting ears
Alternate method of attaching 1U mounting ears
Click to expand in new window
Alternate method of attaching larger mounting ears
Alternate method of attaching mounting ears

Mount the 5320-16P models Under a Table

The 5320-16P switch models are constructed so that they can be mounted under a table. Ensure that the table is strong enough to support the weight of the switch and the attached cables.

To mount a switch under the table, follow these steps.

  1. Using the two holes in each short mounting ear, mark the places under the table to mount the switch. Each mounting ear has two mounting holes, so be sure to make four marks.
  2. Drill a hole at each mark.
  3. Insert a provided anchor into each hole, if an anchor is needed. Gently tap each anchor with a hammer, if necessary, to ensure that it is inserted tightly.
  4. Using rack mount screws, attach a mounting ear to the left side of the switch, at the front end. Under the Table Mount: Attaching larger mounting ears to 5320-16P models shows the attachment of the screws.
  5. Repeat step 4 for the right side of the switch.
  6. Mount the switch under the table by screwing a provided wood screw through each hole in the mounting ears into the anchors. Ensure that all screws are securely fastened and that the switch is firmly attached to under the table.
Click to expand in new window
Under the Table Mount: Attaching 1U mounting ears to 5320-16P models
Under the Table Mount: Attaching 1U mounting ears to 5320-16P models
Click to expand in new window
Under the Table Mount: Attaching larger mounting ears to 5320-16P models
Attaching 5320-16P models under a table for an under the table mount

There is a "cleaner" method of attaching the mounting ears to the switch so that they are tucked under the switch instead of pointing away from the switch. Alternate method of attaching larger mounting ears illustrates attaching the mounting ears so that they are underneath the switch.