Supported Accessories

The AP3000X comes with the AH-ACC-BKT-AX-TB mounting bracket that can be used to mount the access point on flat surfaces, such as Prelude ceilings (15/16 in. ceiling grid), Suprafine ceilings (flat bottomed 9/16 in. ceiling grid), and walls. The ceiling tile sides must be flat.

Note

An integral antenna is an antenna that's fixed to the AP and cannot be disconnected. An integral antenna is also called a fixed antenna or integrated antenna and can be an internal or external antenna.

Supported Antennas

Two important points:

The AP3000X has two integral or fixed antennas which cannot be removed.
The AP3000X comes with two AI-DS0305360-RPSMA antennas which you can attach to the AP and use to extend your coverage.

Note

Unlike with earlier APs, you do not need to order two AI-DS0305360-RPSMA antennas seperately. They are included with the AP.

You can extend or improve your wireless coverage by adding additional antennas to your access point. The following table shows the supported antennas.

Table 1. Supported antennas
Antenna	Technical Specifications
	2.4GHz			5.0GHz
	Port	Gain	Beam	Gain	Beam
ML-2452-HPAG4A6-01	1	4	360	7.3	360
ML-2452-PNA5-01R	1	4.5	120	5	120
ML-2452-APA2-01	1	3.04	360	4.96	360
ML-2452-APA2-02	1	3.04	360	4.96	360
ML-2452-HPA5-036	1	3.9	360	5.7	360
ML-2452-PTA2M2-036	2	4	360	5	360
ML-2452-SEC6M4-036	4	6.92	100	7.3	80
AI-DS0305360-RPSMA	1	3.23	360	5.22	360
AIO-DD75060-RPSMA	2	7.5	60	7.5	60
AIO-DD05120-RPSMA	2	5	120	5	120

Supported Mounting Options

Purchase one of the following accessories if you are installing the access point on a surface other than a standard flat surface.

Table 2. Supported brackets
Accessory	Description
AH-ACC-BKT-AX-TB	Mounting bracket that can be used to mount the access point on flat surfaces such as Prelude ceilings (15/16 in. ceiling grid), Suprafine ceilings (flat bottomed 9/16 in. ceiling grid), and walls. Note: AH-ACC-BKT-AX-TB is included with the access point.
AH-ACC-BKT-AX-IL	Mounting bracket for Interlude ceilings (9/16 in. wide T-bar with center protrusion).
AH-ACC-BKT-AX-SL	Mounting bracket for Silhouette ceilings (ceiling grid with 1/8 in. or 1/4 in. bottom opening).
AH-ACC-BKT-AX-WL	Mounting bracket for direct-to-wall installations when a 1.25 inches of space is desired between the wall and the access point.
ACC-BKT-TB-NF	Mounting bracket for 15/16 in. wide T-bars with sculpted ceiling tiles.
AH-ACC-BKT-916-KIT	Mounting bracket for 9/16 in. wide T-bars with sculpted ceiling tiles.
ACC-BKT-AX-TBW	Mounting bracket for 1.5 in. wide T-bars.
ACC-BKT-AX-BEAM	Mounting bracket for beam mounting.
ACC-BKT-AX-JB	Mounting bracket for junction box or wall mounting.

Supported Power Accessories

You can power the access point through the ETH0 RJ45 Ethernet port. But if you need to power the AP with an external power supply, you can purchase a 12V DC power supply.

There is no wall mount bracket for the 12VDC power supply.

Table 3. Power accessories
Part number	Description
37215	PWR 12 VDC, 2A (24W), 2.5 mm X 5.5 mm connector

Other Accessories

The following table shows the additional accessories available for your access point.

Table 4. Accessories
Part number	Description
ACC-WIFI-MICRO-USB	Extreme Networks micro USB cable. Note: When you connect to the device using the micro USB Console port, the management station from which you connect to the device must have a VT100 emulation program, such as TeraTerm Pro (a free terminal emulator) or Hilgraeve HyperTerminal. Set your baud rate to 115200.