Install the Access Point on a Pole Using KT-147407-02 Bracket Parts and KT-150173-01 Extension Arm

Before you begin

The following hardware is required for pole installation using KT-147407-02 bracket parts and KT-150173-01 extension arm:

  • Flat part of the KT-147407-02 bracket
  • 1-axis tilt part of the KT-147407-02 bracket
  • Pole part of the KT-147407-02 bracket
  • KT-150173-01 extension arm
  • Six M6 screws
  • Four hex-head M12 stainless-steel screws
  • Four hex-head M12 stainless-steel nuts
  • Two 0.5" wide stainless-steel cable clamps
  • One access point

About this task

Install the access point on a pole with all three KT-147407-02 bracket parts and KT-150173-01 extension arm

Procedure

  1. Attach the flat part and the 1-axis tilt part of the KT-147407-02 bracket to the access point.
    For instructions on how to attach the bracket parts, see Attach the flat part and the 1-axis tilt part of the KT-147407-02 bracket to the access point.
  2. Align the circular holes on one end of the KT-150173-01 extension arm against the large holes on the 1-axis tilt bracket.
  3. Attach the KT-150173-01 extension arm to the 1-axis tilt bracket by using two hex-head M12 stainless-steel screws and two hex-head M12 stainless-steel nuts.
  4. Attach the KT-147407-02 pole part to the other end of the KT-150173-01 extension arm using two M12 screws and M12 hex-nuts.
  5. Insert 0.5 in. stainless-steel cable clamps through the KT-147407-02 pole part long slots.
  6. Position the cable clamps around a pole and attach the pole bracket to a pole.
  7. Insert the ends of the cable clamps around the pole and tighten the clamp screws to a torque of 11 in-lbs.

Mount the Access Point to a Pole using the Pole Part of the KT-147407-02 Bracket

Before you begin

The following hardware is required for pole installation using KT-147407-02 pole bracket part to the access point:
  • Pole part of the KT-147407-02 bracket
  • Four M6 screws
  • Two 0.5 in. wide stainless-steel cable clamps
  • One access point

About this task

The pole part of the KT-147407-02 bracket is attached to the access point for pole installation. To mount the access point to a pole using the KT-147407-02 pole bracket part:

Procedure

  1. Attach the pole part of the KT-147407-02 bracket to the access point using four M6 screws.
    Align the four hinges of the pole part of the KT-147407-02 bracket against the holes on the access point to attach the M6 screws.
  2. Attach the pole bracket to a pole by following steps 5, 6, and 7.

Mount the Access Point to a Pole using the Pole Part of the KT-147407-02 Bracket and the KT-150173-01 Extension Arm

Before you begin

The following hardware is required for pole installation using KT-147407-02 pole bracket part and the KT-150173-01 extension arm:
  • Pole part of the KT-147407-02 bracket
  • KT-150173-01 extension arm
  • Four M6 screws
  • Two hex-head M12 stainless-steel screws
  • Two hex-head M12 stainless-steel nuts
  • Two 0.5 in. wide stainless-steel cable clamps
  • One access point

About this task

The extension arm is used with the pole part of the KT-147407-02 bracket on the access point for pole installation. To mount the access point to a pole using the KT-147407-02 pole bracket part and the KT-150173-01 extension arm:

Procedure

  1. Attach the KT-150173-01 extension arm to the access point using two M6 screws.
  2. Attach the pole bracket part of the KT-147407-02 bracket to the other end of the KT-150173-01 bracket using two hex-head M12 stainless-steel screws and two hex-head M12 stainless-steel nuts.
  3. Attach the pole bracket to a pole by following steps 5, 6, and 7.
9036166-04 Rev AB