AP560i Purchase Order Information

AP560i order information

The AP560i access point is sold by itself, and you need to order the mounting brackets and accessories separately for under seat, wall, or pole installations.

Part number Description
AP560i-FCC Cloud-ready, dual 5GHz, dual-band, sensor radio, dual radio 802.11ax/ac/abgn, 4x4:4 MIMO outdoor 11ax access point. Internal Antenna.

Domain: US and Columbia

EIO-04 under-seat enclosure order information

If you need to install the AP560i access point under a seat, you need to purchase the EIO-04 under-seat enclosure.
Note

Note

When you mount the AP on a riser with the metal "L" bracket only and not with a large metal sloping bracket, it is recommended that you add a 3mm stainless steel washer between the “L” brackets and the riser on all of the anchors. The washer provides proper drainage during storms.
Note

Note

Use the EIO-GASKET kit when you have concerns about dirt getting between the AP560i access point rear and the stadium riser.

You must order the EIO-GASKET silicone rubber kit separately.

The ordering details are described in the following table.
Part number Box contents
EIO-04
  • EIO-04 Quick Reference Guide
  • Metal sloping bracket
  • Metal "L" brackets
  • Plastic service panel base
  • Plastic service panel top with one captive screw
  • Conduit covers:
    • Two blank conduit covers for the metal sloping bracket
    • Two blank conduit covers for the service panel base
    • One ½ in. conduit cover each for the metal sloping bracket and the service panel base
    • One ¾ in. conduit cover each for the metal sloping bracket and the service panel base
  • A hardware bag containing the following parts:
    • Six 10 mm M6 screws with integral washer
    • Four 75 mm service panel shoulder screws
    • Four anchor posts
    • Four anchor sleeves
    • Four flat washers for anchors
    • Four lock washers for anchors
    • Anchor assembly instruction sheet
Table 1. EIO-GASKET box contents (ordered separately)
Part number Box contents
EIO-GASKET Two silicone rubber gaskets
Two shoulder screws (security torx, T20 bit-size)
One URL card

KT-147407-02 bracket order information

You can install the access point to a wall using the KT-147407-02 bracket parts (+/-15 degree, 1-axis) or the MBO-ART02 (20 degree increments +/-80 degrees, 10 inch extension).

You can install the access point to a pole using:
  • KT-147407-02 bracket parts (+/-15 degree, 1-axis), or
  • MBO-ART02 (20 degree increments +/-80 degree, 10 inch extension) with the WS-MBO-POLE01 (#30520) bracket
Note

Note

The MBO-ART02 wall mount bracket is End of Sale (EOS) as of January, 2023. It is replaced by the MBO-ART03 bracket.

You can attach the access point to a wall using the MBO-ART02 bracket if you have one. However, if you are using the MBO-ART02 bracket to attach the access point to a pole, you must use the WS-MBO-POLE01 bracket along with the MBO-ART02 bracket.

The WS-MBO-POLE01 bracket is End of Sale (EOS) as of January, 2023.

Note

Note

You cannot attach the access point directly to a pole using the WS-MBO-POLE01 bracket.

The ordering details are described in the following tables:

Part number Box contents
KT-147407-02 The KT-147407-02 bracket comes with three bracket parts:
  • Flat part with holes on the metal surface
  • 1-axis tilt part
  • Boxed pole part with step edges
Six hex-head M6 stainless-steel screws
Two hex-head M12 stainless-steel screws
Two hex-head M12 stainless-steel nuts
One URL card
The KT-147407-02 bracket kit can be used with KT-150173-01 extension arm for wall or pole installations.
Note

Note

You must purchase the KT-150173-01 extension arm separately.

KT-150173-01 extension arm order information

The contents of the KT-150173-01 extension arm are described in the following table.
Part number Box contents
KT-150173-01 One KT-150173-01 12 in. extension arm
Two hex-head M12 stainless-steel screws
Two hex-head M12 stainless-steel nuts
One URL card
Note

Note

You must provide the required M6 hex-head screws and nuts for flat surface installation.

MBO-ART03 bracket order information

Part number Box contents
MBO-ART03 ART03 mounting bracket with +/- 80-degree (in 10-degree increments) and a variable extension of 7.5 inch, 9 inch, or 10.5 inches.
Four stainless-steel M8 screws
Two M6 long hex head screws and hex nuts with lock washer.
One URL card

MBO-ART02 bracket order information

Part number Box contents
MBO-ART02

The MBO-ART02 wall mount bracket is End of Sale (EOS) as of January, 2023. It is replaced by the MBO-ART03 bracket.

ART02 10 in. 2-axis articulating mounting bracket
Four concrete anchors with washers and nuts
Two stainless-steel M6 screws
One hex-head screw
One URL card

WS-MBO-POLE01 bracket order information

Part number Box contents
WS-MBO-POLE01

The WS-MBO-POLE01 bracket is End of Sale (EOS) as of January, 2023.

One WS-MBO-POLE01 bracket
Four M3 screws with nuts and washers
One URL card
9036165-04 Rev AB