SSMD Messages

SSMD-1001

Message:Failed to allocate <Memory size> bytes of memory.

Message Type: DCE

Severity: ERROR

Probable Cause: Indicates that the specified function has failed to allocate memory.

Recommended Action: Check the memory usage on the switch using the show process memory command.

Reload or power cycle the switch.

SSMD-1002

Message: Failed to lock mutex.

Message Type: DCE

Severity: ERROR

Probable Cause: Indicates that System Services Manager (SSM) component has failed to lock the mutex.

Recommended Action: Reload or power cycle the switch.

SSMD-1003

Message: Failed to unlock mutex.

Message Type: DCE

Severity: ERROR

Probable Cause: Indicates that System Services Manager (SSM) component has failed to unlock the mutex.

Recommended Action: Reload or power cycle the switch.

SSMD-1004

Message: SSM startup failed.

Message Type: DCE

Severity: ERROR

Probable Cause: Indicates that the Data Center Ethernet (DCE) System Services Manager (SSM) has encountered an unexpected severe error during basic startup and initialization.

Recommended Action: Reload or power cycle the switch.

If the problem persists, download a new firmware version using the firmware download command.

SSMD-1005

Message: <message>

Note

Note

The message indicates that some packets are permitted/denied by ACL.

Message Type: DCE

Severity: INFO

Probable Cause: Acl logged packets

Recommended Action:ACL log feature enabled.

SSMD-1136

Message: Ethertype Based VLAN Classifier Table is full on Chip <Slot Number>/<Slot Chip Number>:<Chip Core Number>.

Message Type: DCE

Severity: ERROR

Probable Cause: Indicates that Ethertype-based VLAN classifier table is full.

Recommended Action: Clean up the unused Ethertype-based VLAN classifiers to add new ones.

SSMD-1236

Message: MAC Based VLAN Classifier Table is full on Chip <Slot Number>/<Slot Chip Number>:<Chip Core Number>.

Message Type: DCE

Severity: WARNING

Probable Cause:Indicates that MAC-based VLAN classifier table is full.

Recommended Action: Clean up the unused MAC-based VLAN classifiers to add new ones.

SSMD-1400

Message: <ACL Type> access list <ACL Name> is created.

Message Type: DCE

Severity: INFO

Probable Cause: Indicates that the specified access list has been created.

Recommended Action: No action is required.

SSMD-1402

Message: <ACL Type> access list <ACL Name> is deleted.

Message Type: DCE

Severity: INFO

Probable Cause: Indicates that the specified access list has been deleted.

Recommended Action: No action is required.

SSMD-1404

Message: <ACL Type> access list <ACL Name> rule sequence number <rule_sq_no> is <action>.

Message Type: DCE

Severity: INFO

Probable Cause: Indicates that the access list rules are added to or removed from an existing policy.

Recommended Action: No action is required.

SSMD-1405

Message: <ACL Type> access list <ACL Name> configured on interface <Interface Name> at <Direction> by <Configuration source>.

Message Type: DCE

Severity: INFO

Probable Cause: Indicates that the specified access list has been configured on the interface.

Recommended Action: No action is required.

SSMD-1406

Message: <ACL Type> access list <ACL Name> is removed from interface <Interface Name> at <Direction> by <Configuration source>.

Message Type: DCE

Severity: INFO

Probable Cause: Indicates that the specified access list has been removed from the interface.

Recommended Action: No action is required.

SSMD-1407

Message: <ACL Type> access list <ACL Name> active on interface <Interface Name> at <Direction>.

Message Type: DCE

Severity: INFO

Probable Cause: Indicates that the specified access list has been configured on the interface.

Recommended Action: No action is required.

SSMD-1408

Message: <Number of ACL Rules> rules added to <ACL Type> access list <ACL Name>.

Message Type: DCE

Severity:INFO

Probable Cause:Indicates that the specified rules are added to the access control list (ACL).

Recommended Action: No action is required.

SSMD-1409

Message: Inbound ACL mirroring is active on interface <Source mirroring interface>

Message Type: DCE

Severity:INFO

Probable Cause:Indicates that the access list mirroring is enabled.

Recommended Action: No action is required.

SSMD-1410

Message: Inbound ACL mirroring is inactive on interface <Source mirroring interface>

Message Type: DCE

Severity:INFO

Probable Cause:Indicates that the access list mirroring is disabled.

Recommended Action: No action is required.

SSMD-1411

Message: <ACL Type> access list <ACL Name> configured on interface <InterfaceName> shall use interface associated vlan instead of vlan-id provided in rule config.

Message Type: DCE

Severity:INFO

Probable Cause:Indicates that the interface will use interface associated vlan instead of vlan-id provided in rule config.

Recommended Action: No action is required.

SSMD-1412

Message: MAC access list <ACL Name> configured on <VLAN Name> shall use vlan <VLAN Id> instead of vlan-id provided in rule config.

Message Type: DCE

Severity:INFO

Probable Cause:Indicates that the interface will use vlan instead of vlan-id provided in rule config.

Recommended Action: No action is required.

SSMD-1413

Message: <ACL Type> access list <ACL Name> resequence <action>.

Message Type: DCE

Severity:INFO

Probable Cause:Indicates that the access list rules resequence command is success or failure

Recommended Action: No action is required.

SSMD-1436

Message: <ACL Type> access list <ACL Name> partially active on interface <Interface Name> at <Direction>.

Message Type: DCE

Severity:WARNING

Probable Cause:Indicates that the specified access control list (ACL) was not fully instantiated into the ternary content addressable memory (TCAM).

Recommended Action:Remove the specified ACL and other unused ACLs that are applied using the no ip access-groupname[in|out] command, and then instantiate ACL into TCAM again.

SSMD-1437

Message: <ACL Type> access list <ACL Name> inactive on interface <Interface Name> at <Direction>.

Message Type: DCE

Severity:WARNING

Probable Cause: Indicates the specified access control list (ACL) was not instantiated into the ternary content addressable memory (TCAM).

Recommended Action:Remove the specified ACL and other unused ACLs that are applied using the no ip access-groupname[in|out] command, and then instantiate ACL into TCAM again.

SSMD-1438

Message: <ACL Type> access list <ACL Name> configured on interface <Interface Name> at <Direction> has rule(s) which are not supported on this platform.

Message Type: DCE

Severity: WARNING

Probable Cause:Indicates that the specified access control list (ACL) has rules which are not supported on this platform.

Recommended Action: Remove unsupported rules using the no seq 0-4294967290 command in the ACL context.

SSMD-1439

Message: Rule with sequence number <ACL Rule Sequence number> of <ACL Type> access list <ACL Name> configured on interface <Interface Name> at <Direction> is not supported on this platform.

Message Type: DCE

Severity:WARNING

Probable Cause:Indicates that the specified access control list (ACL) has rules which are not supported on this platform.

Recommended Action: Remove unsupported rules using the no seq 0-4294967290 command in the ACL context.

SSMD-1440

Message: <Warning string>

Message Type: DCE

Severity:WARNING

Probable Cause:Indicates that the specified access control list (ACL) has rules which are not supported on this Tcam profile.

Recommended Action: Remove unsupported rules using the no seq 0-4294967290 command in the ACL context.

SSMD-1498

Message: ACL rules with <Feature Name> attributes are now <Feature Status>.

Message Type: DCE

Severity:INFO

Probable Cause:Indicates that the duplicate/conflicting rules are now accepted/rejected by system.

Recommended Action:No action is required.

SSMD-1499

Message: <Featurew Name> is now <Feature Status>.

Message Type: DCE

Severity:INFO

Probable Cause:Indicates that acl-cam-sharing is enabled/disabled in the system.

Recommended Action:No action is required.

SSMD-1536

Message: <Table Mode> <Feature Name> Table is full at <Table Type> on Chip <Slot Number>/<Slot Chip Number>:<Chip Core Number>.

Message Type: DCE

Severity: WARNING

Probable Cause: Indicates that MAC-based VLAN classifier table is full.

Recommended Action: Clean up the unused MAC-based VLAN classifiers to add new ones.

SSMD-1571

Message: Error <Error code> Creating region Feature:<Logical Device ID> Region:<Region ID> Chip:0x<Chip Index>.

Message Type: DCE

Severity: ERROR

Probable Cause: Indicates that the application-specific integrated circuit (ASIC) driver has returned an error.

Recommended Action: Execute the copy support command and contact your switch service provider.

SSMD-1600

Message: App telemetry ACLs are configured successfully using policy file <Policy file Name>.

Message Type: DCE

Severity: INFO

Probable Cause: Indicates that App telemetry ACLs are applied on system.

Recommended Action: No action is required.

SSMD-1601

Message: App telemetry ACLs configured with policy file <Policy file Name> are removed successfully.

Message Type: DCE

Severity: INFO

Probable Cause: Indicates that App telemetry ACLs are removed from system.

Recommended Action: No action is required.

SSMD-1602

Message: App telemetry policy file parsing failed at line number <Line number>.

Message Type: DCE

Severity: ERROR

Probable Cause: Indicates that policy file parsing failed for App telemetry.

Recommended Action: No action is required.

SSMD-1900

Message: Security sub-profile is created for port-profile <Profile name>.

Message Type: DCE

Severity: INFO

Probable Cause: Indicates that a security sub-profile has been created for the specified port-profile.

Recommended Action: No action is required.

SSMD-1901

Message: ACL <ACL name> is configured successfully for security sub-profile of port-profile <Profile name>.

Message Type: DCE

Severity: INFO

Probable Cause: Indicates that the specified access control list (ACL) has been configured for the security sub-profile.

Recommended Action: No action is required.

SSMD-1902

Message: ACL <ACL name> is removed successfully for security sub-profile of port-profile <Profile name>.

Message Type: DCE

Severity: INFO

Probable Cause: Indicates that the specified access control list (ACL) has been removed for the security sub-profile.

Recommended Action: No action is required.

SSMD-1915

Message: Security sub-profile is deleted for port-profile <Profile name>.

Message Type: DCE

Severity: INFO

Probable Cause: Indicates that the security sub-profile has been deleted.

Recommended Action: No action is required.