The following example displays the configuration and state information of the PW client on the MCT cluster.
device# show cluster Cluster c1 ================ Cluster State: Active Bringup Delay: 90 seconds Configured Member Vlan Range: All Active Member Vlan Range: 1 Configured Member BD Range: All Active Member BD Range: 501 No. of Clients: 2 Peer Info: ========== Peer IP: 4.1.1.10, State: Up Peer Interface: Ethernet 0/4, Source IP: 4.1.1.11 Keep-Alive: ========== IP: 10.24.8.220, State: Up Interface: Management 0 (mgmt-vrf), Source IP: 10.24.8.221 Client-Isolation Role: Primary Client Info: ============ Interface Id Description Local/Remote State Exceptions --------- -- ----------- ------------------ ---------- Port-channel 10 1010 Up / Up PW 34816 Up / Up
device# show cluster client-pw Client Info: ============ Interface: PW, client-id: 34816, Deployed, State: Up Description: Local Vlans: Local Bridge Domains : 501 Remote Vlans : Remote Bridge Domains : 501 Number of DF Vlans : 0 Elected DF for vlans : Number of DF Bridge Domains : 1 Elected DF for Bridge Domains : 501
device# show cluster member bridge-domain BD-ID VNI-ID Forwarding state ------- ------ ------------------- 501 4597 Up
device# show bridge-domain 501 Bridge-domain 501 ------------------------------- Bridge-domain Type: MP, VC-ID: 501 MCT Enabled: TRUE Description: Number of configured end-points: 3, Number of Active end-points: 3 VE id: N/A, if-indx: N/A, Local switching: TRUE, bpdu-drop-enable: TRUE PW-profile: default, mac-limit: 0 VLAN: 501 Tagged ports: 1(1 up), Un-tagged ports: 0 (0 up) Tagged ports: po10.501 Un-tagged ports: VNI: 4597 Tunnels: 1(1 up) Tunnels: tu32769.4597 Total VPLS peers: 1 (1 Operational): VC id: 501, Peer address: 9.9.9.9, State: Operational, uptime: 12 min 44 sec Load-balance: False, Cos Enabled: False, Tunnel cnt: 1 rsvp to_a9 (cos_enable:False cos_value:0) Assigned LSPs count:0 Assigned LSPs: Local VC lbl: 800769, Remote VC lbl: 866325, Local VC MTU: 1500, Remote VC MTU: 1500, Local VC-Type: 5, Remote VC-Type: 5 Local PW preferential Status: Active, Remote PW preferential Status: Active Local Flow Label Tx: Disabled, Local Flow Label Rx: Disabled Remote Flow Label Tx: Disabled, Remote Flow Label Rx: Disabled Local Control Word: Disabled, Remote Control Word: Disabled
The following example displays the MAC address table for bridge domain of an MCT cluster.
device# show mac-address-table bridge-domain
Type Code - CCL:Cluster Client Local MAC
CCR:Cluster Client Remote MAC
CR:Cluster Remote MAC
VlanId/BDId Mac-address Type State Ports/LIF/PW/T
501 (B) 0000.0500.0200 Dynamic Active 9.9.9.9
501 (B) 0000.0500.0500 Dynamic-CCL Active Po 10.501
Total MAC addresses : 2
The following example displays all the MAC addresses learned from other VPLS PE nodes over MCT bridge domains.
device# show mac-address-table bridge-domain
Type Code - CCL:Cluster Client Local MAC
CCR:Cluster Client Remote MAC
CR:Cluster Remote MAC
BDId Mac-address Type State Ports/LIF/PW/T
501 (B) 0000.0500.0200 CR Active Tu 32769 (4.1.1.11)
501 (B) 0000.0500.0500 CCR Active Po 10.501
Total MAC addresses : 2