Configuring basic RSTP parameters

Enter global configuration mode.
```
device# configure terminal
```

Enable RSTP.

device(config)# protocol spanning-tree rstp

Designate the root device.

device(conf-rstp)# bridge-priority 28582

Enable the error disable timeout timer value.

device(conf-rstp)# error-disable-timeout enable

Configure the error-disable-timeout interval value.

 
device(conf-rstp)# error-disable-timeout interval 60

Enable edge port on switch ports.
1. Enter interface subtype configuration mode for the switchport.
```
device(conf-rstp)# interface ethernet 0/10 
```
2. Enable edge port.
```
device(conf-if-eth-0/10)# spanning-tree edge-port
```
3. Return to global configuration mode.
```
device(conf-if-eth-0/10)# exit
```
4. Repeat the above steps for all ports that connect to a workstation or PC.
Specify port priorities.
1. Enter interface subtype configuration mode.
```
device(config)# interface ethernet 0/11
```
2. Configure the port priority.
```
device(conf-if-eth-0/11)# spanning-tree priority 1
```
3. Return to global configuration mode.
```
device(conf-if-eth-0/11)# exit
```
Enable the guard root feature.
1. Enter interface configuration mode.
```
device(config)# interface ethernet 0/1
```
2. Configure the port priority.
```
device(conf-if-eth-0/1)# spanning-tree guard root
```
3. Return to privileged EXEC mode.
```
device(conf-if-eth-0/1)# exit
```

Verify the configuration.

 
device# show spanning-tree

Spanning-tree Mode: Rapid Spanning Tree Protocol

Root Id: 4096.01e0.5200.0180 (self)
Bridge Id: 4096.01e0.5200.0180
Root Bridge Forward Delay: 15; Hello Time: 2; Max Age: 20; Max-hops: 20
Configured Forward Delay: 15; Hello Time: 2; Max Age: 20; Max-hops: 20
Number of topology change(s): 0
Bpdu-guard errdisable timeout: disabled
Bpdu-guard errdisable timeout interval: 300 sec
switch# show spanning-tree brief
Spanning-tree Mode: Rapid Spanning Tree Protocol
Root ID Priority 4096
Address 768e.f805.5800
Hello Time 2, Max Age 20, Forward Delay 15
Bridge ID Priority 4096
Address 768e.f805.5800

Interface   Role     Sts     Cost     Prio     Link-type     Edge
---------------------------------------------------------------------
Eth 0/1     DES      FWD     2000     128      P2P           No
Eth 0/10    DES      FWD     2000     128      P2P           No
Eth 0/11    DES      FWD     2000     128      P2P           No

Observe that the settings comply with the formula set out in the STP parameters section, as follows:

(2 × (forward delay - 1)) ≥ maximum age ≥ (2 × (hello time + 1))

or in this case: 28 ≥ 20 ≥ 6.

Save the configuration.

device# copy running-config startup-config

Basic RSTP configuration example

device# configure terminal
device(config)# protocol spanning-tree rstp
device(conf-rstp)# bridge-priority 28582
device(conf-rstp)# error-disable-timeout enable
device(conf-rstp)# error-disable-timeout interval 60
device(conf-rstp)# interface etherne 0/10 
device(conf-if-eth-0/10)# spanning-tree edge-port
device(conf-if-eth-0/10)# exit
device(config)# interface ethernet 0/11
device(conf-if-eth-0/11)# spanning-tree priority 1
device(conf-if-eth-0/11)# exit
device(config)# interface ethernet 0/1
device(conf-if-eth-0/1)# spanning-tree guard root
device(conf-if-eth-0/1)# exit
device# show spanning-tree
device# copy running-config startup-config