Message:Failed to allocate <Memory size> bytes of memory.
Message Type: DCE
Severity: ERROR
Probable Cause: Indicates that the specified function has failed to allocate memory.
Recommended Action: Check the memory usage on the switch using the show process memory command.
Reload or power cycle the switch.
Message: Failed to lock mutex.
Message Type: DCE
Severity: ERROR
Probable Cause: Indicates that System Services Manager (SSM) component has failed to lock the mutex.
Recommended Action: Reload or power cycle the switch.
Message: Failed to unlock mutex.
Message Type: DCE
Severity: ERROR
Probable Cause: Indicates that System Services Manager (SSM) component has failed to unlock the mutex.
Recommended Action: Reload or power cycle the switch.
Message: SSM startup failed.
Message Type: DCE
Severity: ERROR
Probable Cause: Indicates that the Data Center Ethernet (DCE) System Services Manager (SSM) has encountered an unexpected severe error during basic startup and initialization.
Recommended Action: Reload or power cycle the switch.
If the problem persists, download a new firmware version using the firmware download command.
Message: <message>
Note
The message indicates that some packets are permitted/denied by ACL.
Message Type: DCE
Severity: INFO
Probable Cause: Acl logged packets
Recommended Action:ACL log feature enabled.
Message: Ethertype Based VLAN Classifier Table is full on Chip <Slot Number>/<Slot Chip Number>:<Chip Core Number>.
Message Type: DCE
Severity: ERROR
Probable Cause: Indicates that Ethertype-based VLAN classifier table is full.
Recommended Action: Clean up the unused Ethertype-based VLAN classifiers to add new ones.
Message: MAC Based VLAN Classifier Table is full on Chip <Slot Number>/<Slot Chip Number>:<Chip Core Number>.
Message Type: DCE
Severity: WARNING
Probable Cause:Indicates that MAC-based VLAN classifier table is full.
Recommended Action: Clean up the unused MAC-based VLAN classifiers to add new ones.
Message: <ACL Type> access list <ACL Name> is created.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that the specified access list has been created.
Recommended Action: No action is required.
Message: <ACL Type> access list <ACL Name> is deleted.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that the specified access list has been deleted.
Recommended Action: No action is required.
Message: <ACL Type> access list <ACL Name> rule sequence number <rule_sq_no> is <action>.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that the access list rules are added to or removed from an existing policy.
Recommended Action: No action is required.
Message: <ACL Type> access list <ACL Name> configured on interface <Interface Name> at <Direction> by <Configuration source>.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that the specified access list has been configured on the interface.
Recommended Action: No action is required.
Message: <ACL Type> access list <ACL Name> is removed from interface <Interface Name> at <Direction> by <Configuration source>.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that the specified access list has been removed from the interface.
Recommended Action: No action is required.
Message: <ACL Type> access list <ACL Name> active on interface <Interface Name> at <Direction>.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that the specified access list has been configured on the interface.
Recommended Action: No action is required.
Message: <Number of ACL Rules> rules added to <ACL Type> access list <ACL Name>.
Message Type: DCE
Severity:INFO
Probable Cause:Indicates that the specified rules are added to the access control list (ACL).
Recommended Action: No action is required.
Message: Inbound ACL mirroring is active on interface <Source mirroring interface>
Message Type: DCE
Severity:INFO
Probable Cause:Indicates that the access list mirroring is enabled.
Recommended Action: No action is required.
Message: Inbound ACL mirroring is inactive on interface <Source mirroring interface>
Message Type: DCE
Severity:INFO
Probable Cause:Indicates that the access list mirroring is disabled.
Recommended Action: No action is required.
Message: <ACL Type> access list <ACL Name> configured on interface <InterfaceName> shall use interface associated vlan instead of vlan-id provided in rule config.
Message Type: DCE
Severity:INFO
Probable Cause:Indicates that the interface will use interface associated vlan instead of vlan-id provided in rule config.
Recommended Action: No action is required.
Message: MAC access list <ACL Name> configured on <VLAN Name> shall use vlan <VLAN Id> instead of vlan-id provided in rule config.
Message Type: DCE
Severity:INFO
Probable Cause:Indicates that the interface will use vlan instead of vlan-id provided in rule config.
Recommended Action: No action is required.
Message: <ACL Type> access list <ACL Name> resequence <action>.
Message Type: DCE
Severity:INFO
Probable Cause:Indicates that the access list rules resequence command is success or failure
Recommended Action: No action is required.
Message: <ACL Type> access list <ACL Name> partially active on interface <Interface Name> at <Direction>.
Message Type: DCE
Severity:WARNING
Probable Cause:Indicates that the specified access control list (ACL) was not fully instantiated into the ternary content addressable memory (TCAM).
Recommended Action:Remove the specified ACL and other unused ACLs that are applied using the no ip access-groupname[in|out] command, and then instantiate ACL into TCAM again.
Message: <ACL Type> access list <ACL Name> inactive on interface <Interface Name> at <Direction>.
Message Type: DCE
Severity:WARNING
Probable Cause: Indicates the specified access control list (ACL) was not instantiated into the ternary content addressable memory (TCAM).
Recommended Action:Remove the specified ACL and other unused ACLs that are applied using the no ip access-groupname[in|out] command, and then instantiate ACL into TCAM again.
Message: <ACL Type> access list <ACL Name> configured on interface <Interface Name> at <Direction> has rule(s) which are not supported on this platform.
Message Type: DCE
Severity: WARNING
Probable Cause:Indicates that the specified access control list (ACL) has rules which are not supported on this platform.
Recommended Action: Remove unsupported rules using the no seq 0-4294967290 command in the ACL context.
Message: Rule with sequence number <ACL Rule Sequence number> of <ACL Type> access list <ACL Name> configured on interface <Interface Name> at <Direction> is not supported on this platform.
Message Type: DCE
Severity:WARNING
Probable Cause:Indicates that the specified access control list (ACL) has rules which are not supported on this platform.
Recommended Action: Remove unsupported rules using the no seq 0-4294967290 command in the ACL context.
Message: <Warning string>
Message Type: DCE
Severity:WARNING
Probable Cause:Indicates that the specified access control list (ACL) has rules which are not supported on this Tcam profile.
Recommended Action: Remove unsupported rules using the no seq 0-4294967290 command in the ACL context.
Message: ACL rules with <Feature Name> attributes are now <Feature Status>.
Message Type: DCE
Severity:INFO
Probable Cause:Indicates that the duplicate/conflicting rules are now accepted/rejected by system.
Recommended Action:No action is required.
Message: <Featurew Name> is now <Feature Status>.
Message Type: DCE
Severity:INFO
Probable Cause:Indicates that acl-cam-sharing is enabled/disabled in the system.
Recommended Action:No action is required.
Message: <Table Mode> <Feature Name> Table is full at <Table Type> on Chip <Slot Number>/<Slot Chip Number>:<Chip Core Number>.
Message Type: DCE
Severity: WARNING
Probable Cause: Indicates that MAC-based VLAN classifier table is full.
Recommended Action: Clean up the unused MAC-based VLAN classifiers to add new ones.
Message: Error <Error code> Creating region Feature:<Logical Device ID> Region:<Region ID> Chip:0x<Chip Index>.
Message Type: DCE
Severity: ERROR
Probable Cause: Indicates that the application-specific integrated circuit (ASIC) driver has returned an error.
Recommended Action: Execute the copy support command and contact your switch service provider.
Message: App telemetry ACLs are configured successfully using policy file <Policy file Name>.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that App telemetry ACLs are applied on system.
Recommended Action: No action is required.
Message: App telemetry ACLs configured with policy file <Policy file Name> are removed successfully.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that App telemetry ACLs are removed from system.
Recommended Action: No action is required.
Message: App telemetry policy file parsing failed at line number <Line number>.
Message Type: DCE
Severity: ERROR
Probable Cause: Indicates that policy file parsing failed for App telemetry.
Recommended Action: No action is required.
Message: Security sub-profile is created for port-profile <Profile name>.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that a security sub-profile has been created for the specified port-profile.
Recommended Action: No action is required.
Message: ACL <ACL name> is configured successfully for security sub-profile of port-profile <Profile name>.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that the specified access control list (ACL) has been configured for the security sub-profile.
Recommended Action: No action is required.
Message: ACL <ACL name> is removed successfully for security sub-profile of port-profile <Profile name>.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that the specified access control list (ACL) has been removed for the security sub-profile.
Recommended Action: No action is required.
Message: Security sub-profile is deleted for port-profile <Profile name>.
Message Type: DCE
Severity: INFO
Probable Cause: Indicates that the security sub-profile has been deleted.
Recommended Action: No action is required.