switchport

Sets switching mode characteristics for the selected interface

Supported in the following platforms:

Access Points — AP7502, AP7522, AP7532, AP7562, AP7602, AP7612, AP7622, AP7632, AP7662, AP8163, AP8432, AP8533
Wireless Controller — RFS4010
Service Platforms — NX5500, NX7500, NX9500, NX9600, VX9000

Syntax

switchport [access|mode|trunk]

switchport access vlan [<1-4094>|<VLAN-ALIAS-NAME>]

switchport mode [access|trunk]

switchport trunk [allowed|fabric-attach|native]

switchport trunk allowed vlan [<VLAN-ID>|add <VLAN-ID>|none|remove <VLAN-ID>]

swithcport trunk fabric-attach vlan [<1-4094>|<VLAN-ALIAS-NAME>] isid <1-16777214>

switchport trunk native [tagged|vlan [<1-4094>|<VLAN-ALIAS-NAME>]]

Parameters

switchport access vlan [<1-4094>|<VLAN-ALIAS-NAME>]

access vlan [<1-4094>| <VLAN-ALIAS-NAME>]

Sets the VLAN when interface is in the access mode. You can either directly specify the native VLAN ID or use a VLAN alias to identify the native VLAN.

<1-4094> – Specify the SVI VLAN ID from 1 - 4094.
<VLAN-ALIAS-NAME> – Specify the VLAN alias name (should be existing and configured).

An Ethernet port in the access mode accepts packets only from the native VLAN. Frames are forwarded out the port untagged with no 802.1Q header. All frames received on the port are expected as untagged and are mapped to the native VLAN.

switchport mode [access|trunk]

mode [access|trunk]

Sets the interface‘s switching mode to access or trunk (can only be used on physical - layer 2 - interfaces)

access – If access mode is selected, the access VLAN is automatically set to VLAN1. In this mode, only untagged packets in the access VLAN (vlan1) are accepted on this port. All tagged packets are discarded.
trunk – If trunk mode is selected, tagged VLAN packets are accepted. The native VLAN is automatically set to VLAN1. Untagged packets are placed in the native VLAN by the wireless controller or service platform. Outgoing packets in the native VLAN are sent untagged. The default mode for both ports is trunk.

switchport trunk allowed vlan [<VLAN-ID>|add <VLAN-ID>|none|remove <VLAN-ID>]

trunk allowed

Sets trunking mode, allowed VLANs characteristics of the port. Use this option to add VLANs that exclusively send packets over the listed port.

vlan [<VLAN-ID>| add <VLAN-ID>| none| remove <VLAN-ID>

Sets allowed VLAN options. The options are:

<VLAN-ID> – Allows a group of VLAN IDs. Specify the VLAN IDs, can be either a range (55-60) or a comma-separated list (35, 41, etc.)
none – Allows no VLANs to transmit or receive through the layer 2 interface
add <VLAN-ID> – Adds VLANs to the current list
- <VLAN-ID> – Specify the VLAN IDs. Can be either a range of VLAN (55-60) or a list of comma separated IDs (35, 41, etc.)
remove <VLAN-ID> – Removes VLANs from the current list
- <VLAN-ID> – Specify the VLAN IDs. Can be either a range of VLAN (55-60) or a list of comma separated IDs (35, 41, etc.)

Allowed VLANs are configured only when the switching mode is set to “trunk”.

switchport trunk fabric-attach vlan [<1-4094>|<VLAN-ALIAS-NAME>] isid <1-16777214>

trunk	Sets trunking mode characteristics of this Ethernet port
fabric-attach	Enables Fabric Attach (FA) client operation on this Ethernet port. Use this option to enable non-SPB WiNG devices (access points and controllers) as FA Clients. FA enabled switches, in the FC network, send out LLDP messages with TLV extensions of Organization-specific TLV with OUI, to discover FA clients and advertise capabilities. The FA-enabled client associates with the FA Server (FAS), and obtains provisioning information (management VLAN interface details, and whether the interface is tagged or not) that allows the client to be configured with parameters that allow traffic to flow through the Fabric to the WLAN controller. This initial FA Client to WLC communication uses the Fabric‘s default VLAN to I-SID mapping. Use this command to configure the I-SID (Individual Service Identifier) to VLAN mapping that the FA Client uses to negotiate with the FAS. Note: You can configure FA Client capability on a device‘s profile as well as device contexts. Note: This option is enabled only when the switching mode is set to trunk.
vlan [<1-4094>\|<VLAN-ALIAS-NAME>]	Configures the VLAN through which traffic from this device is routed to the FA switch <1-4094> – Specify the VLAN from 1 - 4094. <VLAN-ALIAS-NAME> – Use a VLAN alias to specify the VLAN. If using a VLAN alias, ensure that the alias is existing and configured. The FA Client requests acceptance of the I-SID to VLAN mapping from the FAS within the Fabric Connect (FC) network. Once acceptance is achieved, the FC edge switch applies the I-SID to the VLAN traffic from the device (AP or controller), and uses this I-SID inside the Fabric. Note: Both the FA Client and FA switch (at the edge of the FC network) use LLDP Element and Assignment Type-Length-Values (TLVs) to advertise their identity and FA capabilities.
isid <1-16777214>	Configures the I-SID to be associated with the VLAN interface specified above. isid <1-16777214> – Specify the I-SID from 1 - 16777214. The IEEE Auto-Attach standard requires that the I-SID and VLAN ID be unique per port per switch, so that the device does not enforce duplicate I-SID and VLAN ID for each mapping. Note: A maximum of 94 pairs of I-SID to VLAN mappings can be configured per Ethernet port.

switchport trunk native [tagged|vlan [<1-4094>|<VLAN-ALIAS-NAME>]]

trunk

Sets trunking mode characteristics of the switchport

native [tagged|vlan [<1-4094>| <VLAN-ALIAS-NAME>]]

Configures the native VLAN ID for the trunk-mode port

The native VLAN allows an Ethernet device to associate untagged frames to a VLAN when no 802.1Q frame is included in the frame. Additionally, the native VLAN is the VLAN untagged traffic is directed over when using a port in trunk mode.

tagged – Tags the native VLAN. When a frame is tagged, the 12 bit frame VLAN ID is added to the 802.1Q header enabling upstream Ethernet devices to know which VLAN ID the frame belongs to. The device reads the 12 bit VLAN ID and forwards the frame to the appropriate VLAN. When a frame is received with no 802.1Q header, the upstream device classifies the frame using the default or native VLAN assigned to the Trunk port. A native VLAN allows an Ethernet device to associate untagged frames to a VLAN when no 802.1Q frame is included in the frame.
vlan [<1-4094>|<VLAN-ALIAS-NAME>] – Sets the native VLAN for classifying untagged traffic when the interface is in trunking mode.
- <1-4094> – Specify a value from 1 - 4094.
- <VLAN-ALIAS-NAME> – Specify the VLAN alias name used to identify the VLANs. The VLAN alias should be existing and configured.

Usage Guidelines

Interfaces ge1 - ge4 can be configured as trunk or in access mode. An interface configured as “trunk” allows packets (from the given list of VLANs) to be added to the trunk. An interface configured as “access” allows packets only from native VLANs.

Use the [no] switchport (access|mode|trunk) to undo switchport configurations.

Example

nx9500-6C8809(config-profile-default-rfs4000-if-ge1)#switchport trunk native 
tagged

nx9500-6C8809(config-profile-default-rfs4000-if-ge1)#switchport access vlan 1

nx9500-6C8809(config-profile-default-rfs4000-if-ge1)#show context
 interface ge1
  description "This is GigabitEthernet interface for Royal King"
  speed 10
  duplex full
  switchport mode access
  switchport access vlan 1
  spanning-tree bpduguard enable
  spanning-tree bpdufilter disable
  --More--
nx9500-6C8809(config-profile-default-rfs4000-if-ge1)#

The following is the basic configuration required to enable a device as a FA Client, with tagged native VLAN traffic:

ap8432-070235(config-device-74-67-F7-07-02-35-if-ge1)#switchport mode trunk

ap8432-070235(config-device-74-67-F7-07-02-35-if-ge1)#switchport trunk 
fabric-attach vlan 1 isid 1

ap8432-070235(config-device-74-67-F7-07-02-35-if-ge1)#switchport trunk 
fabric-attach vlan 2 isid 200

ap8432-070235(config-device-74-67-F7-07-02-35-if-ge1)#switchport trunk 
fabric-attach vlan 100 isid 1000

ap8432-070235(config-device-74-67-F7-07-02-35-if-ge1)#switchport trunk 
allowed vlan 1-2,100

ap8432-070235(config-device-74-67-F7-07-02-35-if-ge1)#switchport trunk 
native tagged

ap8432-070235(config-device-74-67-F7-07-02-35-if-ge1)#show context
 interface ge1
  switchport mode trunk
  switchport trunk fabric-attach vlan 1 isid 1
  switchport trunk fabric-attach vlan 2 isid 200
  switchport trunk fabric-attach vlan 100 isid 1000
  switchport trunk native vlan 1
  no switchport trunk native tagged
  switchport trunk allowed vlan 1-2,100
ap8432-070235(config-device-74-67-F7-07-02-35-if-ge1)#

Related Commands

no	Disables or reverts interface settings to their default

Published June 2019prev | next

Email this topic

Print this page Print this page

Leave feedback Feedback