Wireless Controller, Service Platform and Access Point

Creates a MAC ACL deny and/or permit rule, applicable only to the EX3500 switch

Each deny or permit rule consists of a set of match criteria and an associated action, which is deny access for the deny rule and allow access for the permit rule. When applied to layer 2 traffic (between a EX35XX switch and the managed service platform or a VM interface) every packet is matched against the configured match criteria and in case of a match the packet is dropped or forwarded depending on the rule type.

EX35XX devices ( and EX3548) are layer 2 Gigabit Ethernet switches with either 24 or 48 10/100/1000-BASE-T ports, and four SFP transceiver slots for fiber connectivity. Each 10/100/1000 Mbps port supports both the IEEE 802.3af and IEEE 802.3at-2009 PoE standards. An EX35XX switch has an SNMP-based management agent that provides both in-band and out-of-band management access. The EX35XX switch utilizes an embedded HTTP Web agent and CLI, which in spite of being different from that of the operating system provides controllers PoE and port management resources.

Note

To implement the EX3500 MAC ACL rule, apply the MAC ACL directly to a EX35XXwi device, or to an EX35XX profile. For more information, see access-group.

Supported in the following platforms:

Access Points — AP7502, AP7522, AP7532, AP7562, AP7602, AP7612, AP7622, AP7632, AP7662, AP8163, AP8432, AP8533
Wireless Controller — RFS4010
Service Platforms — NX5500, NX7500, NX9500, NX9600, VX9000

Syntax

ex3500 [deny|permit] [all|tagged-eth2|untagged-eth2]

ex3500 [deny|permit] [all|tagged-eth2|untagged-eth2] [any |host <SOURCE-MAC>|
network <SOURCE-MAC> <SOURCE-MAC-MASK>] [any|host <DEST-MAC>|network <DEST-MAC> 
<DEST-MAC-MASK>] [ethertype <0-65535|ethertype-mask <0-65535>|ex3500-time-range 
<TIME-RANGE-NAME>|rule-precedence <1-128>|vlan <1-4094>|vlan-mask <1-4095>]

Parameters

ex3500 [deny|permit] [all|tagged-eth2|untagged-eth2] [any |host <SOURCE-MAC>|
network <SOURCE-MAC> <SOURCE-MAC-MASK>] [any|host <DEST-MAC>|network <DEST-MAC> 
<DEST-MAC-MASK>] [ethertype <0-65535|ethertype-mask <0-65535>|ex3500-time-range 
<TIME-RANGE-NAME>|rule-precedence <1-128>|vlan <1-4094>|vlan-mask <1-4095>]

[deny\|permit]	Creates a deny or permit MAC ACL rule and configures the rule parameters Every EX3500 MAC ACL rule provides a set of match criteria against which incoming and outgoing packets (to and from an EX35XX device) are matched. In case of a match, the packet is dropped or forwarded depending on the rule type. The packet is dropped in case of a deny rule, and forwarded for an permit rule.
[all\|tagged-eth2\| untagged-eth2]	Specifies the packet type all – Applies this deny/permit rule to all packets tagged-eth2 – Applies this deny/permit rule only to tagged Ethernet-2 packets untagged-eth2 – Applies this deny/permit rule only to untagged Ethernet-2 packets After specifying the packet type, configure the source and/or EX3500 MAC addresses to match.
[any\| host <SOURCE-MAC>\| network <SOURCE-MAC> <SOURCE-MAC-MASK>]	Enter the Source MAC addresses any – Identifies all EX3500 devices as a source to match host <SOURCE-MAC> – Identifies a specific EX3500 host as the source to match <SOURCE-MAC> – Specify the source host‘s exact MAC address network <SOURCE-MAC> <SOURCE-MAC-MASK> – Configures a range of MAC addresses as the source to match. Packets received from any of these MAC addresses are dropped. <SOURCE-MAC> – Specify the source MAC address to match. <SOURCE-MAC-MASK> – Specify the source MAC bit mask. For a deny rule, packets received from EX3500 device(s) matching the specified MAC address(es) are dropped. For a permit rule, packets received from EX3500 device(s) matching the specified MAC address(es) are forwarded.
[any\|host <DEST-MAC>\| network <DEST-MAC> <DEST-MAC-MASK>]	Enter the Destination MAC addresses any – Identifies all EX3500 devices as a destination to match host <SOURCE-MAC> – Identifies a specific EX3500 host as the destination to match <SOURCE-MAC> – Specify the destination host‘s exact MAC address network <SOURCE-MAC> <SOURCE-MAC-MASK> – Configures a range of MAC addresses as the destination to match. Packets addressed to any of these MAC addresses are dropped. <SOURCE-MAC> – Specify the destination MAC address to match. <SOURCE-MAC-MASK> – Specify the destination MAC bit mask. For a deny rule, packets addressed to EX3500 device(s) matching the specified MAC address(es) are dropped. For a permit rule, packets addressed to EX3500 device(s) matching the specified MAC address(es) are forwarded.
ether-type <0-65535>	Configures the Ethertype protocol number. The ether type is a two-octet field within an Ethernet frame. It indicates the protocol encapsulated in the payload of an Ethernet frame. <0-65535> – Specify the value from 0 - 65535. The default value is 1.
ethertype-mask <0-65535>	Configures the Ethertype mask <0-65535> – Specify the value from 0 - 65535. The default value is 1.
ex3500-time-range <TIME-RANGE-NAME>	Applies a specified EX3500 time range (should be existing and configured). The deny or permit rule is applied during the time period specified in the EX3500 time range. <TIME-RANGE-NAME> – Specify the time range name. An EX3500 time range list consists of a set of periodic and absolute time range rules. Periodic time ranges recur periodically at specified time periods, such as daily, weekly, weekends, weekdays, and on specific week days, for example on every successive Mondays. Absolute time ranges are not periodic and do not recur. They consist of a range of days during a particular time period (the starting and ending days and time are fixed). Note: For information on configuring EX3500 time-range, see ex3500.
vlan <1-4094>	Configures a VLAN ID representative of the shared SSID each user employs to interoperate within the network (once authenticated by the local RADIUS server) <1-4094> – Specify the VLAN ID from 1 - 4094.
vlan-mask <1-4095>	Configures the VLAN ID bit mask value <1-4095> – Specify the VLAN bit mask from 1 - 4095.
rule-precedence <1-128>	Configures a precedence for this EX3500 MAC ACL <1 - 128> – Specify a value from 1 - 128. ACLs with lower precedence are applied first to packets.

Examples

nx9500-6C8809(config-mac-acl-ex3500MacACL)#ex3500 deny tagged-eth2 any any vlan
20 rule-precedence 1

nx9500-6C8809(config-mac-acl-ex3500MacACL)#show context
mac access-list ex3500MacACL
 ex3500 deny tagged-eth2 any any vlan 20 rule-precedence 1
nx9500-6C8809(config-mac-acl-ex3500MacACL)#

Related Commands

no (mac-acl)

Removes this EX3500 deny/permit rule from the MAC ACL

ex3500 (mac-acl-config-commands)

Supported in the following platforms:

Syntax

Parameters

Examples

Related Commands