Wireless Controller, Service Platform and Access Point

Specifies the 802.11 rates supported on a WLAN

Supported in the following platforms:

Access Points — AP7502, AP7522, AP7532, AP7562, AP7602, AP7612, AP7622, AP7632, AP7662, AP8163, AP8432, AP8533
Wireless Controller — RFS4010
Service Platforms — NX5500, NX7500, NX9500, NX9600, VX9000

Syntax

data-rates [2.4GHz|5GHz]

data-rates 2.4GHz [b-only|bg|bgn|custom|default|g-only|gn]

data-rates 2.4GHz custom [1|11|12|18|2|24|36|48|5.5|54|6|9|basic-1|basic-11|
basic-12|basic-18|basic-2|basic-24|basic-36|basic-48|basic-5.5|basic-54|basic-6|basic-9|
basic-mcs-1s|mcs-1s|mcs-2s|mcs-3s]

data-rates 5GHz [a-only|an|custom|default]

data-rates 5GHz custom [12|18|24|36|48|54|6|9|basic-1|basic-11|basic-12|
basic-18|basic-2|basic-24|basic-36|basic-48|basic-5.5|basic-54|basic-6|basic-9|
basic-mcs-1s|mcs-1s|mcs2s|mcs3s]

Parameters

data-rates 2.4GHz [b-only|bg|bgn|default|g-only|gn]

data-rates	Specifies the 802.11 rates supported when mapped to a 2.4 GHz radio
b-only	Uses rates that support only 11b clients
bg	Uses rates that support both 11b and 11g clients
bgn	Uses rates that support 11b, 11g and 11n clients
default	Uses the default rates configured for a 2.4 GHz radio
g-only	Uses rates that support operation in 11g only
gn	Uses rates that support 11g and 11n clients

data-rates 5GHz [a-only|an|default]

data-rates	Specifies the 802.11 rates supported when mapped to a 5.0 GHz radio
a-only	Uses rates that support operation in 11a only
an	Uses rates that support 11a and 11n clients
default	Uses default rates configured for a 5.0 GHz

data-rates [2.4GHz|5GHz] custom [1|11|12|18|2|24|36|48|5.5|54|6|9|basic-1|basic-11|
basic-12|basic-18|basic-2|basic-24|basic-36|basic-48|basic-5.5|basic-54|basic-6|basic-9|
basic-mcs0-7|mcs0-15|mcs0-7|mcs8-15]

data-rates [2.4GHz\|5GHz]	Specifies the 802.11 rates supported when mapped to a 2.4 GHz or 5.0 GHz radio
custom	Configures a data rates list by specifying each rate individually. Use 'basic-' prefix before a rate to indicate it is used as a basic rate (For example, 'data-rates custom basic-1 basic-2 5.5 11'). The data-rates for 2.4 GHz and 5.0 GHz channels are the same with a few exceptions. The 2.4 GHz channel has a few extra data rates: 1, 11, 2, and 5.5.
1,11,2,5.5	The following data rates are specific to the 2.4 GHz channel: 1 – 1-Mbps 11 – 11-Mbps 2 – 2-Mbps 5.5 – 5.5-Mbps
12,18,24,36,48,54,6,9, basic-1,basic-11, basic-12,basic-18, basic-2, basic-36,basic-48, basic-5.5, basic-54,basic-6, basic-9, basic-mcs0-7,mcs0-15, mcs0-7,mcs8-15	The following data rates are common to both the 2.4 GHz and 5.0 GHz channels: 12 – 12 Mbps 18 – 18-Mbps 24 – 24 Mbps 36 – 36-Mbps 48 – 48-Mbps 54 – 54-Mbps 6 – 6-Mbps 9 – 9-Mbps basic-1 – basic 1-Mbps basic-11 – basic 11-Mbps basic-12 – basic 12-Mbps basic-18 – basic 18-Mbps basic-2 – basic 2-Mbps basic-36 – basic 36-Mbps basic-48 – basic 48-Mbps basic-5.5 – basic 5.5-Mbps basic-54 – basic 54-Mbps basic-6 – basic 6-Mbps basic-9 – basic 9-Mbps basic-mcs-1s – Modulation and coding scheme data rates for 1 Spatial Stream mcs-1s – Applicable to 1-spatial stream data rates mcs-2s – Applicable to 2-spatial stream data rates mcs-3s – Applicable to 3-spatial stream data rates

Examples

nx9500-6C8809(config-wlan-test)#data-rates 2.4GHz gn

nx9500-6C8809(config-wlan-test)#show context
wlan test
 ssid test
 bridging-mode local
 encryption-type none
 authentication-type eap
 accounting syslog host 172.16.10.4 port 2
 data-rates 2.4GHz gn
 client-load-balancing probe-req-intvl 5ghz 5
 client-load-balancing band-discovery-intvl 2
 captive-portal-enforcement fall-back
 acl exceed-rate wireless-client-denied-traffic 20 disassociate
 broadcast-dhcp validate-offer
nx9500-6C8809(config-wlan-test)#

Related Commands

no (wlan-config-mode)

Resets the 802.11 data rates supported on a WLAN for the 2.4 GHz or 5.0 GHz radios