Configure the Insight Interface SLX Endpoint

The Insight Interface is configured on both the SLX endpoint and the TPVM endpoint. Use the following procedure to configure the SLX endpoint of the Insight Interface. Note that steps 1 through 4 are specific to the SLX 9540 and SLX 9640.

Procedure

  1. Enter global configuration mode.
    device# configure terminal
  2. Enter the hardware command to enter hardware configuration mode. (This is required for the SLX 9540/9640 only.)
    device(config)# hardware
  3. Enter the connector command to specify a slot and port.
    device(config-hardware)# connector 0/48
  4. Enter the insight mode command to enable the insight interface on a port-channel, and exit to global configuration mode.
    device(connector-0/48)# insight mode
    

For the SLX 9640 use Eth 0/24. The command will toggle the physical port, and will display as port 0/125 in any show commands.

  1. Exit to global configuration mode.
    device(connector-0/48)# exit
  2. In global configuration mode, specify a port-channel. You can create a new port-channel or use an existing unconfigured port-channel. The Insight Interface can only be configured on one port-channel
    device(config)# interface port-channel 22
    
  3. In interface subtype configuration mode, enter the insight enable command.
    device(config-Port-channel-22)# insight enable
    
  4. Set the port ip-address.
    device(config-Port-channel-20)# ip address 10.0.0.1/24
  5. Enable the interface.
    device(config-Port-channel-22)# no shutdown
    
  6. Use the show interface port-channel and the show port-channel commands to confirm the configuration, as in the following example.
    device# show interface port-channel 22
    Port-channel 22 is up, line protocol is up
    Hardware is AGGREGATE, address is 609c.9f5a.4558
        Current address is 609c.9f5a.4558
    Interface index (ifindex) is 671088673
    Minimum number of links to bring Port-channel up is 1
    MTU 1548 bytes
    LineSpeed Actual     : 10000 Mbit
    Allowed Member Speed : 10000 Mbit
    Priority Tag disable
    Forward LACP PDU: Disable
    Route Only: Disabled
    Last clearing of show interface counters: 1d23h53m
    Queueing strategy: fifo
    Receive Statistics:
        0 packets, 0 bytes
        Unicasts: 0, Multicasts: 0, Broadcasts: 0
        64-byte pkts: 0, Over 64-byte pkts: 0, Over 127-byte pkts: 0
        Over 255-byte pkts: 0, Over 511-byte pkts: 0, Over 1023-byte pkts: 0
        Over 1518-byte pkts(Jumbo): 0
        Runts: 0, Jabbers: 0, CRC: 0, Overruns: 0
        Errors: 0, Discards: 0
    Transmit Statistics:
        5 packets, 380 bytes
        Unicasts: 0, Multicasts: 5, Broadcasts: 0
        Underruns: 0
        Errors: 0, Discards: 0
    Rate info:
        Input 0.000000 Mbits/sec, 0 packets/sec, 0.00% of line-rate
        Output 0.000000 Mbits/sec, 0 packets/sec, 0.00% of line-rate
    Route-Only Packets Dropped: 0
    Time since last interface status change: 00:00:21
    
    device# show port-channel 22
    Static Aggregator: Po 22 
     Aggregator type: Standard
     Number of Ports: 1
     Member ports:
       Eth 0/125   *