vx9000
Configures a
Virtual WLAN Controller
(V-WLC) in a
virtual machine (VM) environment. V-WLC can be deployed on a shared,
third-party server hardware, thereby reducing overhead costs of procuring and maintaining
dedicated appliances. The external, third-party hardware needs to have installed hypervisors,
such as VmWare, Xen, VirtualBox, KVM, Amazon EC2 or Hyper-V, enabling it to communicate with
V-WLC software.
The V-WLC controls and manages access points and other controllers (at NOC
or as a site-controller) in the network. The traffic between the access points and the V-WLC
is over the layer-3 MINT protocol.
V-WLC is a licensed feature, and the
WiNG software provides the following two new
licenses:
- VX – When installed, this license
activates VM controller instance, and enables the V-WLC to trigger adoption process
allowing access points to adopt to the V-WLC. The adoption capacity of the V-WLC is
determined by the number of licenses installed on it.
- VX – When installed, this license
activates VM controller instance, and enables the V-WLC to trigger adoption process
allowing access points to adopt to the V-WLC. The adoption capacity of the V-WLC is
determined by the number of licenses installed on it.
To install the VX or VX-DEMO license on an existing V-WLC instance, use the
license command. For more information, see the examples provided in this
section.
Supported in the following platforms:
Parameters
vx9000 <MAC>
| vx9000 <MAC> |
Configures a V-WLC and enters its configuration mode.
The V-WLC configuration is the same as that of a normal controller. |
|
Examples
nx9500-6C8809(config)#vx9000 11-22-33-44-55-66
nx9500-6C8809(config-device-11-22-33-44-55-66)#?
Device Mode commands:
adopter-auto-provisioning-policy-lookup Use centralized auto-provisioning
policy when adopted by another
controller
adoption Adoption configuration
adoption-site Set system's adoption site
adoption-mode Configure the adoption mode for the
access-points in this RF-Domain
alias Alias
application-policy Application Poicy configuration
area Set name of area where the system
is located
arp Address Resolution Protocol (ARP)
auto-learn Auto learning
autogen-uniqueid Autogenerate a unique id
autoinstall Autoinstall settings
bluetooth-detection Detect Bluetooth devices using the
Bluetooth USB module - there will
be interference on 2.4 Ghz radio in
wlan mode
bridge Ethernet bridge
captive-portal Captive portal
cdp Cisco Discovery Protocol
channel-list Configure channel list to be
advertised to wireless clients
cluster Cluster configuration
configuration-persistence Enable persistence of configuration
across reloads (startup configfile)
contact Configure the contact
controller WLAN controller configuration
country-code Configure the country of operation
critical-resource Critical Resource
crypto Encryption related commands
database Database command
device-upgrade Device firmware upgrade
dot1x 802.1X
dpi Enable Deep-Packet-Inspection
(Application Assurance)
dscp-mapping Configure IP DSCP to 802.1p
priority mapping for untagged
frames
email-notification Email notification configuration
enforce-version Check the firmware versions of
devices before interoperating
environmental-sensor Environmental Sensors Configuration
events System event messages
export Export a file
file-sync File sync between controller and
adoptees
floor Set the floor within a area where
the system is located
geo-coordinates Configure geo coordinates for this
device
gre GRE protocol
hostname Set system's network name
http-analyze Specify HTTP-Analysis configuration
interface Select an interface to configure
ip Internet Protocol (IP)
ipv6 Internet Protocol version 6 (IPv6)
l2tpv3 L2tpv3 protocol
l3e-lite-table L3e lite Table
layout-coordinates Configure layout coordinates for
this device
led Turn LEDs on/off on the device
led-timeout Configure the time for the led to
turn off after the last radio state
change
legacy-auto-downgrade Enable device firmware to auto
downgrade when other legacy devices
are detected
legacy-auto-update Auto upgrade of legacy devices
license License management command
lldp Link Layer Discovery Protocol
load-balancing Configure load balancing parameter
location Configure the location
logging Modify message logging facilities
mac-address-table MAC Address Table
mac-auth 802.1X
mac-name Configure MAC address to name
mappings
management-server Configure management server address
memory-profile Memory profile to be used on the
device
meshpoint-device Configure meshpoint device
parameters
meshpoint-monitor-interval Configure meshpoint monitoring
interval
min-misconfiguration-recovery-time Check controller connectivity after
configuration is received
mint MiNT protocol
mirror Mirroring
misconfiguration-recovery-time Check controller connectivity after
configuration is received
mpact-server MPACT server configuration
neighbor-inactivity-timeout Configure neighbor inactivity
timeout
neighbor-info-interval Configure neighbor information
exchange interval
no Negate a command or set its
defaults
noc Configure the noc related setting
nsight NSight
ntp Ntp server WORD
offline-duration Set duration for which a device
remains unadopted before it
generates offline event
override Override a command
override-wlan Configure RF Domain level overrides
for wlan
power-config Configure power mode
preferred-controller-group Controller group this system will
prefer for adoption
preferred-tunnel-controller Tunnel Controller Name this system
will prefer for tunneling extended
vlan traffic
radius Configure device-level radius
authentication parameters
raid RAID
remove-override Remove configuration item override
from the device (so profile value
takes effect)
rf-domain-manager RF Domain Manager
router Dynamic routing
rsa-key Assign a RSA key to a service
sensor-server AirDefense sensor server
configuration
slot PCI expansion Slot
spanning-tree Spanning tree
timezone Configure the timezone
traffic-class-mapping Configure IPv6 traffic class to
802.1p priority mapping for
untagged frames
trustpoint Assign a trustpoint to a service
tunnel-controller Tunnel Controller group this
controller belongs to
use Set setting to use
vrrp VRRP configuration
vrrp-state-check Publish interface via OSPF/BGP only
if the interface VRRP state is not
BACKUP
wep-shared-key-auth Enable support for 802.11 WEP
shared key authentication
clrscr Clears the display screen
commit Commit all changes made in this
session
do Run commands from Exec mode
end End current mode and change to EXEC
mode
exit End current mode and down to
previous mode
help Description of the interactive help
system
revert Revert changes
service Service Commands
show Show running system information
write Write running configuration to
memory or terminal
nx9500-6C8809(config-device-11-22-33-44-55-66)#
Print
this page
Email this topic
Feedback
View PDF
Download EPUB