Configure Port-Based Mirroring in a Multi-Tenant Architecture

You can configure port-based mirroring in a multi-tenant architecture.

About this task

Follow this procedure to configure post-based mirroring.

Procedure

  1. Run the following commands to configure access control list applications on Ethernet or port channel and VLAN or virtual Ethernet: 
    efa tenant service mirror session create –-name <session-name> --tenant <tenant-name>
        
   --source {<device-ip>,<eth | po | vlan>,<if-name>}
   --type {<source-device-ip>,<eth | po | vlan>,<source-if-name>:<port-based | flow-based>}
        
   --destination {<source-device-ip>,<eth | po | vlan>,<source-if-name> : 
	            <destination-device-ip>,<eth | po | vlan>,<destination-if-name}
   --destination-type {<source-device-ip>,< eth | po | vlan>,<source-if-name>:<span>}
                	

   --direction {<source-device-ip>,< eth | po | vlan>,<source-if-name> : <tx | rx | both>}


(efa:root)root@node-2:~# efa tenant show
+------------+--------+------+-----+------+------+-------+----------------------+-------------------+
|    Name    |  Type  | VLAN |L2VNI| L3VNI| VRF  | Enable|         Ports        |   Mirroring Ports |
|            |        | Range|Range| Range| Count| BD    |                      |                   |
+------------+--------+------+-----+------+------+-------+----------------------+-------------------+
|sharedTenant| shared |      |     |      | 0    | false |                      | 10.20.246.15[0/31]|
|            |        |      |     |      |      |       |                      | 10.20.246.16[0/31]|
|            |        |      |     |      |      |       |                      | 10.20.246.21[0/31]|
|            |        |      |     |      |      |       |                      | 10.20.246.22[0/31]|
|            |        |      |     |      |      |       |                      | 10.20.246.25[0/31]|
|            |        |      |     |      |      |       |                      | 10.20.246.26[0/31]|
+------------+--------+------+-----+------+------+-------+----------------------+-------------------+
|    ten1    | private| 11-20|     |      | 10   | false | 10.20.246.15[0/1-10] |                   | 
|            |        |      |     |      |      |       | 10.20.246.16[0/1-10] |                   |
+------------+--------+------+-----+------+------+-------+----------------------+-------------------+
|    ten2    | private| 21-30|     |      | 10   | false | 10.20.246.15[0/11-20]|                   |
|            |        |      |     |      |      |       | 10.20.246.16[0/11-20]|                   |
+------------+--------+------+-----+------+------+-------+----------------------+-------------------+


(efa:root)root@node 2:~# efa tenant po show
+-------+-------+----+------+-----+------------+---------+--------+-------------------+-----------+-------------+------------+
|  Name | Tenant| ID |Speed | MTU |Negotiation |Min Link |  Lacp  |        Ports      |    State  |  Dev State  |  App State |
|       |       |    |      |     |            |  Count  | Timeout|                   |           |             |            |
+-------+-------+----+------+-----+------------+---------+--------+-------------------+-----------+-------------+------------+
|ten1po1| ten1  |  2 |10Gbps|     |   active   |   1     |   long | 10.20.246.15[0/1] | po-created| provisioned | cfg-in-sync|
|       |       |    |      |     |            |         |        | 10.20.246.16[0/1] |           |             |            |
+-------+-------+----+------+-----+------------+---------+--------+-------------------+-----------+-------------+------------+
|ten2po1| ten2  |  3 |10Gbps|     |   active   |   1     |   long | 10.20.246.15[0/11]| po-created| provisioned | cfg-in-sync|
|       |       |    |      |     |            |         |        | 10.20.246.16[0/11]|           |             |            |
+-------+-------+----+------+-----+------------+---------+--------+-------------------+-----------+-------------+------------+
    Example:
    10.20.246.15
    efa tenant service mirror session create --name ten1mirrorsession1 --tenant ten1
    --source 10.20.246.15,po,ten1po1
    --type 10.20.246.15,po,ten1po1:port-based
    
    --destination 10.20.246.15,po,ten1po1:10.20.246.15,eth,0/31
    --destination-type 10.20.246.15,po,ten1po1:span
    
    --direction 10.20.246.15,po,ten1po1:both
    		 10.20.246.16
    efa tenant service mirror session create –name ten1mirrorsession2 --tenant ten1
    --source 10.20.246.16,po,ten1po1
    --type 10.20.246.16,po,ten1po1:port-based

    --destination 10.20.246.16,po,ten1po1:10.20.246.16,eth,0/31
    --destination-type 10.20.246.16,po,ten1po1:span

    --direction 10.20.246.16,po,ten1po1:both
    10.20.246.15
    efa tenant service mirror session create –name ten2mirrorsession1 --tenant ten2
    --source 10.20.246.15,po,ten2po1
    --type 10.20.246.15,po,ten2po1:port-based

    --destination 10.20.246.15,po,ten2po1:10.20.246.15,eth,0/31
    --destination-type 10.20.246.15,po,ten2po1:span
                
    --direction 10.20.246.15,po,ten2po1:both
    		 10.20.246.16
    efa tenant service mirror session create –name ten2mirrorsession2 --tenant ten2
    --source 10.20.246.16,po,ten2po1
    --type 10.20.246.16,po,ten2po1:port-based

    --destination 10.20.246.16,po,ten2po1:10.20.246.16,eth,0/31
    --destination-type 10.20.246.16,po,ten2po1:span

     --direction 10.20.246.16,po,ten2po1:both
  2. Verify the switch configuration on the SLX device.
    10.20.246.15
    SLX# show running-config monitor session
monitor session 1
 source port-channel 2 destination ethernet 0/31 direction both
!monitor session 2
 source port-channel 3 destination ethernet 0/31 direction both
!
SLX# show monitor session 1
Session                 : 1
Type                    : SPAN
Description             : [None]
State                   : Enabled
Source Interface        : Po 2 (Down)
Destination Interface   : Eth 0/31 (Down)
Direction               : Both
Type                    : port-based

SLX# show monitor session 2
Session                 : 2
Type                    : SPAN
Description             : [None]
State                   : Enabled
Source Interface        : Po 3 (Down)
Destination Interface   : Eth 0/31 (Down)
Direction               : Both
Type                    : port-based
    		 10.20.246.16
    SLX# show running-config monitor session
monitor session 1
 source port-channel 2 destination ethernet 0/31 direction both
!monitor session 2
 source port-channel 3 destination ethernet 0/31 direction both
!
SLX# show monitor session 1
Session                 : 1
Type                    : SPAN
Description             : [None]
State                   : Enabled
Source Interface        : Po 2 (Down)
Destination Interface   : Eth 0/31 (Down)
Direction               : Both
Type                    : port-based

SLX# show monitor session 2
Session                 : 2
Type                    : SPAN
Description             : [None]
State                   : Enabled
Source Interface        : Po 3 (Down)
Destination Interface   : Eth 0/31 (Down)
Direction               : Both
Type                    : port-based
9037725-01 RevAA