Configure ICL Port Mirroring in a Multi-Tenant Architecture

You can configure an ICL port mirroring in a multi-tenant architecture.

About this task

Follow this procedure to configure an ICL port mirroring.

Procedure

  1. Run the following commands to configure access control list applications on Ethernet or Port channel and VLAN or Virtual Ethernet: 
    efa tenant epg create --name <epg-name> --tenant <tenant-name>

    --type port-profile
    --po <mirror-source-po-list>
        
    --pp-ipv6-acl-in <acl-name>
    --pp-ip-acl-in <acl-name> --pp-ip-acl-out <acl-name>
  2. Run the following commands to configure a mirror session: 
    efa tenant service mirror session create –name <session-name> --tenant <tenant-name>
    --source {<device-ip>,<eth | po | vlan>,<if-name>}
    --type {<source-device-ip>,<eth | po | vlan>,<source-if-name>:<port-based | flow-based>}

    --destination-type {<source-device-ip>,< eth | po | vlan>,<source-if-name>:<span>}
    --destination {<source-device-ip>,<eth | po | vlan>,<source-if-name> : 
			<destination-device-ip>,<eth | po | vlan>,<destination-if-name}
    --direction {<source-device-ip>,< eth | po | vlan>,<source-if-name> : <tx | rx | both>}


(efa:root)root@node-2:~# efa tenant show
+-------+------+------+------+------+------+-------+----------------------------+-------------------+
|Name   | Type | VLAN | L2VNI|L3VNI | VRF  |Enable |           Ports            |  Mirroring Ports  |
|       |      | Range| Range|Range | Count|BD     |                            |                   |
+-------+------+------+------+------+------+-------+----------------------------+-------------------+
|shared |Shared|      |      |      |   0  |false  |10.20.246.15[0/46-47]       |10.20.246.15[0/31] |
|Tenant |      |      |      |      |      |       |10.20.246.16[0/46-47]       |10.20.246.16[0/31] |
|       |      |      |      |      |      |       |10.20.246.21[0/9-10,0/46-48]|10.20.246.21[0/31] |
|       |      |      |      |      |      |       |10.20.246.22[0/9-10,0/46-48]|10.20.246.22[0/31] |
|       |      |      |      |      |      |       |                            |10.20.246.25[0/31] |
|       |      |      |      |      |      |       |                            |10.20.246.26[0/31] |
+-------+------+------+------+------+------+-------+----------------------------+-------------------+


(efa:root)root@node 2:~# efa tenant po show
+-------+------+--+------+---+-----------+--------+-------+----------------+-----------+------------+-----------+
|  Name |Tenant|ID|Speed |MTU|Negotiation|Min Link| Lacp  |     Ports      |   State   | Dev State  | App State |
|       |      |  |      |   |           |Count   |Timeout|                |           |            |           |
+-------+------+--+------+---+-----------+--------+-------+----------------+-----------+------------+-----------+
|ten1po1|ten1  |64|10Gbps|   |   active  |   1    |  long |10.20.246.15    |po-created |provisioned |cfg-in-sync|
|       |      |  |      |   |           |        |       |[0/46-47]       |           |            |           |
|       |      |  |      |   |           |        |       |10.20.246.16    |           |            |           |
|       |      |  |      |   |           |        |       |[0/46-47]       |           |            |           |
+-------+------+--+------+---+-----------+--------+-------+----------------+-----------+------------+-----------+
|ten2po1|ten2  |64|10Gbps|   |   active  |   1    |  long |10.20.246.21    |po-created |provisioned |cfg-in-sync|
|       |      |  |      |   |           |        |       |0/9-10,0/46-48] |           |            |           |
|       |      |  |      |   |           |        |       |10.20.246.22|   |           |            |           |
|       |      |  |      |   |           |        |       |[0/9-10,0/46-48]|           |            |           |
+-------+------+--+------+---+-----------+--------+-------+----------------+-----------+------------+-----------+
    Example
    efa tenant epg create –name ten1epg1 –tenant ten1 --type port-profile
  --po ten1po1
  --pp-ipv6-acl-in ext-ipv6-permit-any-mirror-acl
    efa tenant service mirror session create –name mirrorsession1 --tenant ten1
  --source 10.20.246.15,po,ten1po1
  --type 10.20.246.15,po,ten1po1:port-based
  --destination 10.20.246.15,po,ten1po1:10.20.246.15,eth,0/31
  --destination-type 10.20.246.15,po,ten1po1:span
  --direction 10.20.246.15,po,ten1po1:tx
    efa tenant service mirror session create –name mirrorsession2 --tenant ten1
  --source 10.20.246.15,po,ten1po1
  --type 10.20.246.15,po,ten1po1:flow-based
  --destination 10.20.246.15,po,ten1po1:10.20.246.15,eth,0/31
  --destination-type 10.20.246.15,po,ten1po1:span
  --direction 10.20.246.15,po,ten1po1:rx
    		 
    efa tenant epg create –name ten1epg2 –tenant ten1 --type port-profile
  --po ten1po2
  --pp-ipv6-acl-in ext-ipv6-permit-any-mirror-acl
    efa tenant service mirror session create –name mirrorsession3 --tenant ten1
  --source 10.20.246.21,po,ten1po2
  --type 10.20.246.21,po,ten1po2:port-based 
  --destination 10.20.246.21,po,ten1po2:10.20.246.21,eth,0/31
  --destination-type 10.20.246.21,po,ten1po2:span
  --direction 10.20.246.21,po,ten1po2:tx
    efa tenant service mirror session create –name mirrorsession4 --tenant ten1
  --source 10.20.246.21,po,ten1po2
  --type 10.20.246.21,po,ten1po2:flow-based
  --destination 10.20.246.21,po,ten1po2:10.20.246.21,eth,0/31
  --destination-type 10.20.246.21,po,ten1po2:span
  --direction 10.20.246.21,po,ten1po2:rx
  3. Verify the switch configuration on the SLX device.
    10.20.246.15
    SLX# show running-config ipv6 access-list
ipv6 access-list extended ext-ipv6-permit-any-mirror-acl
 seq 10 permit ipv6 any any mirror
!
SLX#

SLX# show running-config int po 64
interface Port-channel 64
 mtu 9216
 description MCTPeerInterface
 ip address 10.20.20.3/31
 ipv6 access-group ext-ipv6-permit-any-mirror-acl in
 no shutdown
!
SLX#
    		 10.20.246.16
    SLX# show running-config ipv6 access-list
ipv6 access-list extended ext-ipv6-permit-any-mirror-acl
 seq 10 permit ipv6 any any mirror
!
SLX#

SLX# show running-config int po 64
interface Port-channel 64
 mtu 9216
 description MCTPeerInterface
 ip address 10.20.20.2/31
 ipv6 access-group ext-ipv6-permit-any-mirror-acl in
 no shutdown
!
SLX#
    10.20.246.21
    SLX# show running-config ipv6 access-list
ipv6 access-list extended ext-ipv6-permit-any-mirror-acl
 seq 10 permit ipv6 any any mirror
!
SLX#

SLX# show running-config int po 64
interface Port-channel 64
 mtu 9216
 description MCTPeerInterface
 ip address 10.20.20.3/31
 ipv6 access-group ext-ipv6-permit-any-mirror-acl in
 no shutdown
!
SLX#
    		 10.20.246.22
    SLX# show running-config ipv6 access-list
ipv6 access-list extended ext-ipv6-permit-any-mirror-acl
 seq 10 permit ipv6 any any mirror
!
SLX#

SLX# show running-config int po 64
interface Port-channel 64
 mtu 9216
 description MCTPeerInterface
 ip address 10.20.20.2/31
 ipv6 access-group ext-ipv6-permit-any-mirror-acl in
 no shutdown
!
SLX#
    10.20.246.15
    SLX# show running-config monitor session
monitor session 1
 source port-channel 64 destination ethernet 0/31 direction tx
!
monitor session 2
 source port-channel 64 destination ethernet 0/31 direction rx flow-based
!
SLX# show monitor session 1
Session                : 1
Type                   : SPAN
Description            : [None]
State                  : Enabled
Source Interface       : Po 64 (Up)
Destination Interface  : Eth 0/31 (Down)
Direction              : Tx
Type                   : port-based

SLX# show monitor session 2
Session                : 2
Type                   : SPAN
Description            : [None]
State                  : Enabled
Source Interface       : Po 64 (Up)
Destination Interface  : Eth 0/31 (Down)
Direction              : Rx
Type                   : flow-based
    		 10.20.246.21
    SLX# show running-config monitor session
monitor session 1
 source port-channel 64 destination ethernet 0/31 direction tx
!
monitor session 2
 source port-channel 64 destination ethernet 0/31 direction rx flow-based
!
SLX# show monitor session 1
Session                : 1
Type                   : SPAN
Description            : [None]
State                  : Enabled
Source Interface       : Po 64 (Up)
Destination Interface  : Eth 0/31 (Down)
Direction              : Tx
Type                   : port-based

SLX# show monitor session 2
Session                : 2
Type                   : SPAN
Description            : [None]
State                  : Enabled
Source Interface       : Po 64 (Up)
Destination Interface  : Eth 0/31 (Down)
Direction              : Rx
Type                   : flow-based
9037725-01 RevAA