Configure Fabric Extend Logical Interfaces

Configure a Fabric Extend (FE) logical interface using the procedure that applies to your deployment.

Configure Fabric Extend Logical Interfaces for Native Support

Use this procedure to configure the Fabric Extend logical interface on a Fabric Engine switch.

Configuring Fabric Extend (FE) consists of two primary tasks: configuring the tunnel source address and configuring the logical interface. These tasks must be completed on both ends of the tunnel.

Before you begin

Configure the Fabric Extend tunnel with a tunnel source IP address. See Configure Fabric Extend Tunnels.

About this task

VRF is an optional parameter. If you do not configure a VRF, then FE uses the GRT.

For a logical IS-IS interface, Layer 2 and Layer 3 refer to the following use cases:

  • Layer 2 — Fabric Extend VID (FE-VID)

  • Layer 3 — Fabric Extend IP (FE-IP)

Procedure

  1. In the navigation pane, expand Configuration > Fabric.
  2. Select IS-IS.
  3. Select the Logical Interfaces tab.
  4. Select Insert.
  5. For Id, type the index number that uniquely identifies this logical interface.
  6. For Name, type the name of this logical interface.
  7. For Type, select the type of core network that the tunnel will traverse:
    Note

    Note

    Different fields are available depending on the type of core network you select.

    • If it is a Layer 2 Core, select layer2.
    • If it is a Layer 3 Core, select ip.
  8. Optional: For BFDEnable, select enable to enable BFD.
  9. For a Layer 2 Core, configure the following fields:
    1. For DestIfIndex, select the physical port that the logical interface connects to or enter the name of the MLT.
    2. For Vids, type the list of VLANs for this logical interface.
    3. For PrimaryVid, type the primary tunnel VLAN ID.
      Note

      Note

      The primary VLAN ID must be one of the VIDs listed in the Vids field.

  10. For a Layer 3 Core, complete the following field:
    1. For DestIPAddr, type the destination IP address for the logical interface.
    2. For ISIS Mtu, enter the Maximum Transmission Unit value, in bytes.
      Note

      Note

      Fabric Extend Tunnel IS-IS MTU configuration is added to the document in advance of Fabric Extend Integration with ExtremeCloud SD-WAN support. Feature support is planned for 8.10.1.

  11. Select Insert.

What to do next

Configure Fabric Extend on the switch at the other end of the tunnel. Use the procedures that apply to that model of switch.

Logical Interfaces Field Descriptions

Use the data in the following table to use the Logical Interfaces tab and the Insert Logical Interfaces dialog. The available fields in the dialog differ depending on the type of core you select: layer 2 or ip.

Name

Description

Id

Specifies the index number that uniquely identifies this logical interface.

This field displays on the Insert Logical Interfaces dialog only.

IfIndex

Specifies the index number that uniquely identifies this logical interface. This field is read-only.

This field displays on the Logical Interfaces tab only.

Name

Specifies the administratively assigned name of this logical interface, which can be up to 64 characters.

Type

Specifies the type of logical interface to create:

  • Specify layer 2 for a Layer 2 core network that the tunnel will traverse.

  • Specify ip for a Layer 3 core network that the tunnel will traverse.

DestIPAddr

Specifies the destination IP address for the IP-type logical interface.

DestIfIndex

Specifies the physical port or MultiLink Trunking (MLT) that the Layer 2 logical interface is connected to.

Vids

Specifies the list of VLANs that are associated with this logical interface.

PrimaryVid

Specifies the primary tunnel VLAN ID associated with this Layer 2 Intermediate-System-to-Intermediate-System (IS-IS) logical interface.

ISIS MTU

Note:

Fabric Extend Tunnel IS-IS MTU configuration is added to the document in advance of Fabric Extend Integration with ExtremeCloud SD-WAN support. Feature support is planned for 8.10.1.

Specifies the Maximum Transmission Unit (MTU) size in bytes for IS-IS packets that use this logical interface. The default value is 1600.

CircIndex

Identifies the IS-IS circuit created under the logical interface.

This field displays on the Logical Interfaces tab only.

NextHopVrf

Displays the next-hop VRF name to reach the logical tunnel destination IP.

This field displays on the Logical Interfaces tab only.

BfdEnable

Enables or disables BFD on an IS-IS Logical Interface.

Origin

Specifies the origin of the IS-IS logical interface configuration, either through Zero Touch Fabric Configuration (ZTF) or manual configuration (config) through CLI or EDM.