Use the enable rollback and no enable rollback commands to enable or disable rollback, respectively.
device(config)# rollback enable device(config)#no rollback enable %%WARN: All checkpoints and rollback logs will be cleared! Do you want to continue? [y/n]:
Use the rollback checkpoint command to create a default configuration checkpoint.
device# rollback checkpoint default_config_checkpoint description "Default Config" Checkpoint default_config_checkpoint creation request by user: admin Checkpoint default_config_checkpoint creation completed successfully.
Use the show rollback checkpoint command to view checkpoint details. The summary option is used here.
device# show rollback checkpoint summary User checkpoint summary ------------------------------- 1) default_config: Created by "admin" Created at Tue Jun 12 14:19:49 2018 Size is 4880 bytes Description: "Default Config" 2) vlan_config: Created by "admin" Created at Tue Jun 13 14:19:49 2018 Size is 4872 bytes Description: "Vlan Config"
Depending on the requirements, the running configuration can be modified as needed, as shown in the vlan configuration below.
device# conf t Entering configuration mode terminal device(config)# vlan 100 device(config-vlan-100)# name "VLAN 100" device(config-vlan-100)# exit device(config)# vlan 200 device(config-vlan-200)# name "VLAN 200" device(config-vlan-200)# exit device(config)# no snmp-server enable trap device(config)# end
Use the show rollback diff checkpoint command to view a diff between a checkpoint and a running configuration. Entries removed are indicated by "-" and entries added are indicated by "+".
device# show rollback diff checkpoint default_config_checkpoint ! -snmp-server enable trap +! +vlan 100 + name VLAN 100 +! +vlan 200 + name VLAN 200
The following shows a diff between two checkpoints.
device# show rollback diff checkpoint default checkpoint switchport interface Ethernet 1/10 - switchport port-security shutdown-time 10 - switchport trunk native-vlan 2 + switchport port-security max 100
Use the show rollback patch checkpoint command to view a patch between a checkpoint and the running configuration.
device# show rollback patch checkpoint default_config_checkpoint ! no vlan 200 no vlan 100 ! snmp-server enable trap !
Use the rollback apply checkpoint command to execute a rollback. To rollback the configuration to a specific, saved checkpoint, the rollback configuration name for that checkpoint must be used. Please note that any changes made to the configuration after the checkpoint was taken will be removed when the rollback is performed.
device# rollback apply checkpoint default_config_checkpoint This operation will modify the running configuration of the system. Do you want to continue? [Y/N]y % Warning: Configuration Rollback is in-progress. Please do not abort an ongoing session as it can leave the system with an inconsistent configuration. ...... Rollback completed successfully.
Use the show rollback diff checkpoint command to verify that the diff is empty.
device# show rollback diff checkpoint default_config_checkpoint device#
Use the show rollback status command to view rollback status.
device# show rollback status Operation : Rollback To Checkpoint Checkpoint Name : default_config_checkpoint Rollback done By : admin Rollback Mode : Best Effort Start Time : Tue Jun 12 14:27:04 2018 End Time : Thu Jan 12 14:27:31 2018 Time Taken : 27 seconds Status : Success device#
Use the show rollback log command to view the rollback log.
device# show rollback log vlan 6 no description no suppress-arp no ipv6 mld snooping startup-query-interval no ip igmp snooping startup-query-interval no suppress-nd no router-interface Ve ! exit vlan 3 no description no suppress-arp no ipv6 mld snooping startup-query-interval no ip igmp snooping startup-query-interval no suppress-nd no router-interface Ve ! exit vlan 2 no description no suppress-arp no ipv6 mld snooping startup-query-interval no ip igmp snooping startup-query-interval no suppress-nd no router-interface Ve ! exit vlan 1 no ipv6 mld snooping startup-query-interval no ip igmp snooping startup-query-interval ! exit no ip access-list standard acl1 no ip mtu no ipv6 mtu no mtu no vrf CFD1722809 event-handler ev1 action python-script show_interface.py Error: flash://show_interface.py script for event handler ev1 could not be found or read. router bgp neighbor 1.1.1.1 remote-as 13 Warning: Reset the neighbor session
Use the show rollback log errors command to view log errors.
device# show rollback log errors no bridge-domain 1 p2mp %Error: One or more specified vlan(s) has a VE configured. port 50055 % Error: Cannot update/delete port and transport configurations once the Telemetry server is activated.
Use the show rollback status current command to view current status.
device# show rollback status current Operation : Rollback To Checkpoint Checkpoint Name : vlan-config Rollback done By : admin Rollback Mode : best-effort Start Time : Thu Apr 5 09:32:24 2018 Status : In-Progress
Use the show rollback status history command to view status history.
device# show rollback status history Operation : Rollback To Checkpoint Checkpoint Name : vlan-config Rollback done By : admin Rollback Mode : best-effort Start Time : Thu Apr 5 09:32:24 2018 End Time : Thu Apr 5 09:32:57 2018 Time Taken For Rollback : 33 seconds Status : Success Operation : Rollback To Checkpoint Checkpoint Name : bgp-config Rollback done By : admin Rollback Mode : best-effort Start Time : Thu Apr 5 07:32:24 2018 End Time : Thu Apr 5 07:32:57 2018 Time Taken For Rollback : 38 seconds Status : Success