show ports rate-limit flood

show ports { port_list | port_group | tag tag} rate-limit flood {out-actions | out-of-profile {disabled-ports}} {no-refresh | refresh}

Description

Displays rate-limit discard statistics.

Syntax Description

port_list Specifies one or more ports or slots and ports.
port_group Port group name.
tag Display ports in VMAN/VLANs with this IEEE 802.1Q or 802.1ad tag
tag Tag ID between 1 and 4095.
rate-limit Displays rate-limit discard statistics.
flood Flood traffic.
out-actions Display out-of-profile actions.
out-of-profile Display rate-limit out-of-profile status.
disabled-ports Display ports that have been disabled due to out-of-profile status.
no-refresh Specifies a static snapshot of data.
refresh Specifies a continous refresh of output.

Default

N/A.

Usage Guidelines

This command displays the per port ingress rate-limit flood traffic counter as well as information about received packets that have not been discarded due to rate-limiting.

It is used to show the results of the configure ports port_list rate-limit flood [broadcast | multicast | unknown-destmac] [no-limit | pps] command.

Note

Note

As part of the system health check, the system polls the Rate-limit Flood Counters every 5 minutes and looks for non-zero counters on a port. A HAL.RateLimit.Info log message is logged when this is first detected on a port to alert the user that something in the network has triggered the rate limiting to occur. The message is not be logged again unless the counters are cleared.

Example

Following is sample out put from this command:

* switch # show ports rate-limit flood
Port Rate-Limit Discard Monitor                         Wed Oct  8 13:15:00 2008
Port    Link      Rx Pkt      Rx Byte       Rx Pkt     Rx Pkt   Flood Rate
State   Count     Count        Bcast        Mcast     Exceeded
================================================================================
1         A       0            0            0            0            0
2         A       0            0            0            0            0
3         R       0            0            0            0            0
4         R       0            0            0            0            0
5         R       0            0            0            0            0
6         R       0            0            0            0            0
7         R       0            0            0            0            0
8         R       0            0            0            0            0
9         R       0            0            0            0            0
10        R       0            0            0            0            0
11        R       0            0            0            0            0
12        R       0            0            0            0            0
13        R       0            0            0            0            0
14        R       0            0            0            0            0
15        R       0            0            0            0            0
16        R       0            0            0            0            0
================================================================================
> indicates Port Display Name truncated past 8 characters
Link State: A-Active, R-Ready, NP-Port Not Present, L-Loopback
0->Clear Counters  U->page up  D->page down ESC->exit

The following command displays information without a screen refresh on a switch:

show ports rate-limit flood no-refresh

Following is sample out put from this command:

* switch # show ports rate-limit flood no-refresh
Port Rate-Limit Discard Monitor
Port    Link      Rx Pkt      Rx Byte       Rx Pkt    Rx Pkt   Flood Rate
State   Count     Count        Bcast        Mcast     Exceeded
=========================================================================
1       A         0            0            0            0            0
2       A         0            0            0            0            0
3       R         0            0            0            0            0
4       R         0            0            0            0            0
5       R         0            0            0            0            0
6       R         0            0            0            0            0
7       R         0            0            0            0            0
8       R         0            0            0            0            0
9       R         0            0            0            0            0
10      R         0            0            0            0            0
11      R         0            0            0            0            0
12      R         0            0            0            0            0
13      R         0            0            0            0            0
14      R         0            0            0            0            0
15      R         0            0            0            0            0
16      R         0            0            0            0            0
17      R         0            0            0            0            0
18      R         0            0            0            0            0
19      A         0            0            0            0            0
20      A         0            0            0            0            0
21      R         0            0            0            0            0
22      R         0            0            0            0            0
23      R         0            0            0            0            0
24      R         0            0            0            0            0
25      R         0            0            0            0            0
26      R         0            0            0            0            0
27      R         0            0            0            0            0
28      R         0            0            0            0            0
================================================================================
> indicates Port Display Name truncated past 8 characters
Link State: A-Active, R-Ready, NP-Port Not Present L-Loopback
The following examples use the out-actions and out-of-profile keywords:
# show ports rate-limit flood out-actions             
                                 
                                 Out-actions
Port     Flood Type          Log  Trap  Disable
                                           Port
-------  ----------------    ---  ----  -------
1        Unknown Dest MAC    On   On    Off
1        Broadcast           On   On    Off 
1        Multicast           On   On    Off
2        Unknown Dest MAC    On   Off   On
2        Broadcast           On   Off   On 
2        Multicast           On   Off   On
. . .  

# show ports rate-limit flood out-of-profile 

Port     Flood Type        Status             Counter
-------  ----------------  --------------  ----------
1        Unknown Dest MAC  Out of profile  1234567890
1        Broadcast         Ok                       0
1        Multicast         Ok                       0
2        Unknown Dest MAC  Ok                       0
2        Broadcast         Out of profile       12345      
. . .  

# show ports rate-limit flood out-of-profile disabled-ports 
Disabled
Port      Flood Type        Status             Counter
--------  ----------------  --------------  ----------
2         Broadcast         Out of profile       12345      
. . .

History

This command was first available in ExtremeXOS 12.2.

The port-group, out-actions, out-of-profile, disabled-ports, and refresh options were added in ExtremeXOS 16.1.

Platform Availability

This command is available on the ExtremeSwitching X435, X440-G2, X450-G2, X460-G2, X465, X590, X620, X670-G2, X690, X695, and X870 series switches.